X10 POWERHORN PH508 Bedienungsanleitung

X10 Wireless Technology, Inc. Limited One Year Warranty

X10.com, a division of X10 Wireless Technology, Inc. (X10) warrants X10

products to be free from defective material and workmanship for a period of

one (1) year from the original date of purchase at retail. X10 agrees to repair

or replace, at its sole discretion, a defective X10 product if returned to X10

within the warranty period and with proof of purchase. If service is required

under this warranty:

Call 1-800-442-5065, visit www.x10.com, or e-mail [email protected].

For help or more information on setup, please visit:

http://www.x10.com/support

PH508-04/03

POWERHORN™Remote Siren, Model PH508

INSTALLATION AND OPERATING INSTRUCTIONS

1. Set theHousecodedialon thePOWERHORNtothe sameletterasyour

security system (Model DS7000, or DC8700).*

2. If you want to control the POWERHORN from other types of X10

controllers, set the Unit Code dial on thePOWERHORNto any unused

number between 1 & 16.*

3. Plug the POWERHORN into an AC outlet (not one that is controlled by

a wall switch, in case the switch accidentally gets turned off).

4. To test thePOWERHORN, trip your alarm system. ThePOWERHORN

willsoundforaslongasthealarminthesecuritysystemconsolesounds,

and then shut off a few seconds after you disarm the alarm.

WARNING:

The POWERHORN is extremely loud. To avoid permanent hearing

damage, do not stand too close to it when you trip the alarm.

5. To trip thePOWERHORNfrom anyX10controller (ifyou hear astrange

noise at night, for example): Press Unit Code-ON, then Unit Code-OFF,

then Unit Code-ON, repeatedly. The POWERHORN will sound for as

longasyoukeeppressingONandOFFandwillstopafewsecondsafter

you stop pressing buttons. Or press All Lights On, then All Units Off,

repeatedly. The POWERHORN will sound for as long as you keep

pressing All Lights On, followed by All Units Off and will stop a few

seconds after you stop pressing buttons.

* Note: If you have a DC8700 security system it might be set to flash lights

set to Unit Code 13. If that is the case set the POWERHORN to Unit Code

13.

Powerhorn™

1

9

513

15 3

711

•

•

•

••

•

•

A

I

EM

OC

GK

•

•

•

•

••

•

•

Set the Housecode to

the same letter as your

X10 Controllers and/

or Security System.

Set the Unit Code to

any unused number

(set to 13 if you have

a DC8700 Security

System).

Andere X10 Sicherheitssystem Handbücher

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung