Xerox CUSTOMER TIPS 7425/7428/7435 Bedienungsanleitung

Xerox Multifunction Devices

Customer Tips

PDL Reference Guide for the

WorkCentre 7425/7428/7435

dc09cc0453

June 10, 2009

…for the use

Accessing Extended Features

Overview

This document applies

to the This document enables you to access the extended features of the WorkCentre

7425/7428/7435 in environments that do not have a custom print driver.

stated Xerox

product. It is assumed

that your device is

equipped with the

appropriate option(s)

to support the

information within this

document.

Note: The commands and syntax used in this document requires familiarity with either

PostScript (PS) or Printer Command Language (PCL).

This document provides the Printer Description Language (PDL) commands and syntax

for each feature. The following items are also included:

•A PCL table that describes the PCL features the WorkCentre supports and the syntax

to use the feature.

•A PS table that describes the PS features the WorkCentre supports and the syntax to

use the feature.

This document is not intended to be a complete PS or PCL reference manual. It is a

guide for using the PS and PCL commands with the WorkCentre 7425/7428/7435. Refer

to these sources for additional PS and PCL information:

•PostScript Language Reference Manual, Third Edition, ISBN 0-201-38922-8,

•PCL5 Printer Language Technical Reference Manual

(http://h20000.www2.hp.com/bc/docs/support/SupportManual/bpl13210/bpl13210.pdf),

•Printer Job Language Technical Reference Manual

(http://h20000.www2.hp.com/bc/docs/support/SupportManual/bpl13208/bpl13208.pdf), a

Hewlett-Packard manual.

Using this Guide

Search the Feature Table to determine whether the feature you wish to use is

supported.

Verify that the feature is supported by the platform. For example, the WorkCentre

must have an optional finisher installed to use stapling commands.

Follow across the table to find the syntax listed for the PDL examples shown.

Reference the “Dependencies/Caveats” section when working with PS and/or PCL

commands.

dc09cc0453

Customer Support Page 1

PCL

This WorkCentre supports PCL5e and PCL XL emulations that enable the features listed in the following

table.

Feature Description

Job Name The value for Job Name is stored for printing on the banner page.

Custom Paper Size Customer designated paper size on which to print a job.

Media Size The size of media on which to print a job.

Media Source Specifies the tray to supply the job’s media.

Output Location Indicates the output bin where the completed print job is sent.

Stapling Indicates use and location of staple(s).

Punch Indicates use, location, and number of holes to be punched.

Booklet This command enables you to print documents as booklets. The pages are

reordered sequentially and are oriented so when folded, the paging is

correct.

Collation Collated creates a set that includes 1 copy of each page. Uncollated

creates a stack of multiple copies of the same page.

Resolution Resolution used to image a job.

Quantity Use this command to specify the number of collated sets of a document.

Simplex Delivers one-sided output.

Duplex Delivers two-sided output.

Orientation Delivers output in landscape or portrait orientation.

Force Short Edge

Feeding Rotates orientation of job.

Job Mode Specifies the Job Mode.

Job Type Specifies Confidential Print or Proof Print.

Interleaving Paper

(transparency

separator)

Insert blank media to separate sheets of transparent media.

Job Based

Accounting Allows entry of an accounting code and user ID. To enable this feature the

optional Network Accounting kit is required.

Auditron

Delayed Print Specify the time to print a job.

dc09cc0453

Customer Support Page 2

PCL/PJL Implementation

The following table contains the PCL feature commands and shows the syntax required to use the feature.

After the table are examples of how to use these commands and examples of a PCL file.

Feature Implementation Values

Job Name @PJL SET JOBNAME =

"jobname-string" Where jobname-string is a maximum of 32

characters

Custom

Paper Size –

available only

for PCL

You have to specify by PCL:

<ESC>&l101A

Width of Custom Paper is specified by

<ESC>&f#I

where # equals decipoints (89 mm – 320.0

mm).

Length of Custom Paper is specified by

<ESC>&f#J

where # equals decipoints (98 mm – 483

mm).

For instance:

4.25-inch x 5.5-inch will give

<ESC>&f3060I3960J by

4.25-inch x 720 decipoints/inch = 3060

and

5.5-inch x 720 decipoints/inch = 3960

Media Size @PJL SET PAPER = value Where value is one of the following:

A3: A3 (297 x 420mm)

A4: A4 (210 x 297mm)

A5: A5 (148 x 210mm) *

JISB4: B4 (257 x 364mm)

JISB5: B5 (182 x 257mm)

STATEMENT: Statement (5.5 x 8.5”) *

EXECUTIVE: Executive (7.25 x 10.5”) *

LETTER: Letter (8.5 x 11”)

JISEXEC: 8.5 x 13”

LEGAL: Legal (8.5 x 14”)

LEDGER: Tabloid (11 x 17”)

ROC16K = 16K (194 x 267mm) *

ROC8K = 8K (267 x 388mm) *

16KAIGCO = 16K (195 x 270mm) *

8KAIGCO = 8K (270 x 390mm) *

* Whether each paper is available depends on

NV memory setting.

The following paper sizes are only available with

bi-pass tray.

A6: A6 (105 x 148mm)

JISB6: B6 (128 x 182mm)

8X10 = 8 x 10"

SPANISH = 215 x 315mm

11X15 = 11 x 15"

A4COVER = A4 Cover (223 x 297mm)

LETTERCOVER = 9 x 11"

12X18 = Oversized Tabloid (12 x 18")

SA3 = SRA3 (320 x 450mm)

dc09cc0453

Customer Support Page 3

Feature Implementation Values

JPOST = Postcard (100 x 148mm)

JPOSTD = Postcard (148 x 200mm)

POSTCARD = Postcard (4 x 6")

50X70 = 5 x 7"

TYOUKEI3 = Envelope (120 x 235mm)

COM10 = No. 10 Envelope (4.1 x 9.5”)

MONARCH = Monarch Envelope (3.9 x 7.5”)

DL = DL Envelope (110 x 220mm)

C5 = C5 Envelope (162 x 229mm)

<ESC>&l int A Where int is one of the following:

25 = A5 (148 x 210mm) *

26 = A4 (210 x 297mm)

27 = A3 (297 x 420mm)

45 = B5 (182 x 257mm)

46 = B4 (257 x 364mm)

41 = Statement (5.5 x 8.5") *

1= Executive (7.25 x 10.5") *

2= Letter (8.5 x 11")

18 = 8.5 x 13"

3= Legal (8.5 x 14")

6= Tabloid (11 x 17")

219 = 16K (194 x 267mm) *

220 = 8K (267 x 388mm) *

* Whether each paper is available depends

on NV memory setting.

The following paper sizes are only available with

bypass tray.

24 = A6 (105 x 148mm)

44 = B6 (128 x 182mm)

208 = 8 x 10"

43 = 215 x 315mm

217 = 11 x 15"

200 = A4 Cover (223 x 297mm)

201 = 9 x 11"

213 = Oversized Tabloid (12 x 18")

197 = SRA3 (320 x 450mm)

71 = Postcard (100 x 148mm)

72 = Postcard (148 x 200mm)

216 = Postcard (4 x 6")

204 = 5 x 7"

218 = Envelope (120 x 235mm)

81 = No. 10 Envelope (4.1 x 9.5”)

80 = Monarch Envelope (3.9 x 7.5”)

90 = DL Envelope (110 x 220mm)

91 = C5 Envelope (162 x 229mm)

dc09cc0453

Customer Support Page 4

Feature Implementation Values

Media

Source @PJL SET MEDIASOURCE

= value Where value is one of the following:

TRAY1: Feed from paper tray1

TRAY2: Tray2

TRAY3: Tray3

TRAY4: Tray4

TRAY5: Tray5 (Bypass)

<ESC>&l int H Where int is one of the following:

0: Feed paper from default tray

4: Tray1

1: Tray2

5: Tray3

8: Tray4

20 = Auto

2or 3= Tray5 (Bypass)

Output

Location @PJL SET OUTBIN = value Where value is one of the following:

UPPER: Center Tray

MAINTRAY: Center Tray

CENTERTRAY: Center Tray

MAINTRAY2: Center Tray - Upper

LOWER: Left Top Tray (Face Up)

SIDETRAY: Left Top Tray (Face Up)

MAINTRAY3: Right Top Tray (w/ B-Finisher

or C-Finisher)

OUTBIN101: Finisher Tray (w/ A-Finisher or

B-Finisher or C-Finisher)

BOOKLETTRAY: Right Bottom

Tray(Booklet Maker) (w/

C-Finisher and booklet

module)

<ESC>&l int G Where int is one of the following:

0: Automatic Selection

1: Center Tray

2: Left Top Tray (Face Up)

4: Center Tray - Upper

6: Finisher tray (w/ finisher)

Stapling @PJL SET STAPLE = value Where value is one of the following:

TOPDUAL

TOPLEFT

TOPRIGHT

BOTTOMDUAL

BOTTOMLEFT

BOTTOMRIGHT

LEFTDUAL

RIGHTDUAL

SADDLE

NONE

dc09cc0453

Customer Support Page 5

Feature Implementation Values

Punch @PJL SET PUNCH =

value1

@PJL SET JOBATTR =

”@PNHN = value2”

Where value1 is one of the following:

TOP

RIGHT

LEFT

BOTTOM

NONE

Where value2 is one of the following:

TWO: 2 holes

THREE: 3 holes

FOUR: 4 holes

Folding @PJL SET JOBATTR =

"@FOLD = value1" Where value1 is one of the following:

BIFOLDINSIDE ：Bi-Folding(single page)

BIFOLDMULTIOUTSIDE：Bi-Folding(multi

page)

The "Collated" feature needs to be enabled for

the booklet functions to work.

Booklet @PJL SET JOBATTR =

“@BKLT = value1”

@PJL SET JOBATTR =

“@BKSG = value2”

@PJL SET JOBATTR =

“@BKDN = int1”

@PJL SET JOBATTR =

“@BKDN = int2”

Where value1 is one of the following:

NONEDIVIDE: Compile a booklet as long

as the number of sheet does not exceed the

limit

AUTODIVIDE: Divide sheets into sets

automatically in case of exceeding the limit

number of sheets.

MANUALDIVIDE : Divide sheets based on

the specified limit manually

OFF : Do not compile a booklet

Where value2 is one of the following:

RIGHT = Right to left page order binding

LEFT = Left to right page order binding

Where int1 is:

1-9999 = Booklet dividing number for each

set

Where int2 is:

1 - 9999 = Booklet total pages of document

Collation @PJL SET QTY = int Where int is:

1 - 999

Resolution @PJL SET RESOLUTION =

value Where value is one of the following:

600

1200

Bits Per Pixel @PJL SET BITSPERPIXEL

= value Where value is one of the following:

1: 1 bit per pixel (per plane)

Quantity @PJL SET COPIES = int Where int is:

1-999

(This parameter used for uncollated mode.)

dc09cc0453

Customer Support Page 6

Feature Implementation Values

<ESC>&l int X Where int is:

1-999

@PJL SET DUPLEX =

value1 Where value1 is one of the following:

OFF: simplex

Simplex

<ESC>&l int s Where int is one of the following:

0: simplex

@PJL SET DUPLEX =

value1

@PJL SET BINDING =

value2

Where value1 is one of the following:

ON: duplex

Where value2 is one of the following:

LONGEDGE

SHORTEDGE

(value2 is used combined with value1 = ON)

Duplex

<ESC>&l int s Where int is one of the following:

1: Duplex Long Edge Binding

2: Duplex Short Edge Binding

@PJL SET ORIENTATION

= value Where value is one of the following:

PORTRAIT

LANDSCAPE

Orientation

<ESC>&l int O Where int is one of the following:

0: Portrait

1: Landscape

2: Reverse Portrait

3: Reverse Landscape

Force short

edge feeding @PJL SET

PAPERDIRECTION = value Where value is one of the following:

SEF: Short Edge Feed

LEF: Long Edge Feed

Job Mode @PJL JOB MODE = value Where value is one of the following:

PRINTER for Printer

Job Type @PJL SET HOLD = value1

(See Example 3)

@PJL SET HOLDKEY

="four-digit string"

(See Example 4)

Where value1 is one of the following:

PROOF: proof print

STORE: confidential print (secure print)

The HOLDKEY variable acts as a password

without encryption to protect a held job.

Four-digit string can be any four-digit value

from 0000 to 9999. The default value is "".

When "" (null) is specified, no password is

required.

Interleaving

Paper

(Transparency

Separator)

@PJL SET SLIPSHEET =

value Where value is one of the following:

OFF: no slipsheet

BLANK: blank slipsheet

COPY: imaged slipsheet

dc09cc0453

Customer Support Page 7

Feature Implementation Values

Job Based

Accounting

Auditron

@PJL SET JOBATTR =

"@JOAU = string1"

@PJL SET JOBATTR =

"@JOAP = string2"

@PJL SET JOBATTR =

"@DAID = string3"

Where string1 is a maximum of 32 characters

(ASCII characters in the range 20h - 7EH

only) as job owner (Capital character & small

character is distinguished)

Where string2 is a maximum of 12 characters

(ASCII characters in the range 20h - 7Eh only)

as password without encryption. It can be null

(zero length string)

Where string3 is a maximum of 32 characters

(ASCII characters in the range 20h - 7Eh only)

as account ID. It can be null (zero length

string)

Note: Auditron and JBA cannot be used at the

same time. So the same command works for

both modes.

Delay Print @PJL SET JOBATTR =

"@PRTM =

YYYY:MM:DD:hh:mm"

YYYY:MM:DD:hh:mm

YYYY: year (AD 2000 - 2099)

MM: month (1 - 12)

DD: day (1 - 31)

hh: hour (0 - 23)

mm: minute (0 - 59)

Banner Sheet @PJL SET JOBATTR=

"@BANR=value" Where value is one of the following:

START: start sheet

DEVICE: depend on device setting

OFF: no banner sheet

PJL Template

This section illustrates a standard PJL template that is used to access general print features as

well as WorkCentre Product specific features. This template lists each feature and the syntax,

both PCL commands and PJL, required to use these features. The next section of this document

contains other examples of how to use these commands.

Section 1 (Opening Command, Required for all files)

<ESC>%-12345X@PJL JOB MODE=PRINTER

Section 2 (PJL Set Commands)

@PJL SET RESOLUTION=600

@PJL SET COPIES=1

Section 3 (PCL Code used to invoke PCL Language)

@PJL ENTER LANGUAGE=PCL

Section 4 (PCL Data Stream or ASCII Document inserted here for Options such as

selection Different Fonts, Simplex, Duplex, etc.)

,,,,,,,,,,

Section 5 (Closing Command, Required at end of Document)

<ESC>%-12345X@PJL EOJ

dc09cc0453

Customer Support Page 8

Sample PJL Headers

This section contains examples of these commands in use.

Example 1 Simple Print

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL COMMENT Beginning PCL Job<CR><LF>

@PJL SET OUTBIN=MAINTRAY<CR><LF>

@PJL SET QTY=1<CR><LF>

@PJL SET RESOLUTION=600<CR><LF>

@PJL SET JOBATTR="@JOAU=John"<CR><LF>

Example 2 Finishing Options (Stapling)

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL SET OUTBIN=OUTBIN101<CR><LF>

@PJL SET FINISH=ON<CR><LF>

@PJL SET STAPLE=TOPLEFT<CR><LF>

Example 3 Finishing Options (Punch)

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL SET OUTBIN=OUTPIN101<CR><LF>

@PJL SET FINISH=ON<CR><LF>

@PJL SET PUNCH=LEFT<CR><LF>

@PJL SET JOBATTR="@PNHN=TWO"<CR><LF>

Example 4 Finishing Options (Saddle stapling and folding)

It is an example of division in every 5 sheets.

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL SET OUTBIN=BOOKLETTRAY<CR><LF>

@PJL SET FINISH=ON<CR><LF>

@PJL SET STAPLE=SADDLE<CR><LF>

@PJL SET JOBATTR="@FOLD=BIFOLDMULTIOUTSIDE"<CR><LF>

@PJL SET JOBATTR="@BKLT=MANUALDIVIDE"<CR><LF>

@PJL SET JOBATTR="@BKSG=LEFT"<CR><LF>

@PJL SET JOBATTR="@BKDN=5"<CR><LF>

Example 5 Finishing Options (Bi-Folding(multi page))

It is an example of division in every 5 sheets.

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL SET OUTBIN=BOOKLETTRAY<CR><LF>

@PJL SET FINISH=NONE<CR><LF>

@PJL SET STAPLE=NONE <CR><LF>

@PJL SET JOBATTR="@FOLD=BIFOLDMULTIOUTSIDE"<CR><LF>

@PJL SET JOBATTR="@BKLT=MANUALDIVIDE"<CR><LF>

@PJL SET JOBATTR="@BKSG=LEFT"<CR><LF>

@PJL SET JOBATTR="@BKDN=5"<CR><LF>

@PJL SET QTY=1<CR><LF>

dc09cc0453

Customer Support Page 9

Example 6 Finishing Options (Bi-Folding(single page))

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL SET OUTBIN=BOOKLETTRAY<CR><LF>

@PJL SET FINISH=NONE<CR><LF>

@PJL SET STAPLE=NONE <CR><LF>

@PJL SET JOBATTR="@FOLD=BIFOLDINSIDE"<CR><LF>

@PJL SET JOBATTR="@BKSG=LEFT"<CR><LF>

Example 7 Proof Print

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL SET HOLD=PROOF <CR><LF>

@PJL SET USERNAME="John" <CR><LF>

@PJL SET JOBNAME="Job1" <CR><LF>

Example 8 Confidential (Secure) Print without encryption

Password: 1234

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL SET HOLD=STORE <CR><LF>

@PJL SET HOLDKEY="1234"<CR><LF>

@PJL SET USERNAME="John" <CR><LF>

@PJL SET JOBNAME="Job1" <CR><LF>

Example 9 Banner Sheet

banner: start sheet

@PJL SET JOBATTR="@BANR=START"<CR><LF>

@PJL SET JOBATTR="@BCMT=Banner Comment String"<CR><LF>

Example 10 Job Based Accounting & Auditron

userID: Patricia, Password: none, accountID: none

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL SET JOBATTR="@JOAU=Patricia"<CR><LF>

@PJL SET JOBATTR="@JOAP="<CR><LF>

@PJL SET JOBATTR="@DAID="<CR><LF>

dc09cc0453

Customer Support Page 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Xerox Multifunktionsdrucker Handbücher

Xerox

Xerox 3210 - workcentre b/w laser Bedienungsanleitung

Xerox

Xerox DC230LP Gebrauchsanweisung

Xerox

Xerox WORKCENTRE 5135 Betriebsanleitung

Xerox

Xerox CopyCentre C75 Bedienungsanleitung

Xerox

Xerox WORKCENTRE C2424 Bedienungsanleitung

Xerox

Xerox WorkCentre 5845 Bedienungsanleitung

Xerox

Xerox WORKCENTRE 7775 Bedienungsanleitung

Xerox

Xerox WorkCentre 7300 Series Betriebsanleitung

Xerox

Xerox WorkCentre Pro 40 Bedienungsanleitung

Xerox

Xerox WorkCentre 7228 Bedienungsanleitung

Xerox

Xerox 700i Bedienungsanleitung

Xerox

Xerox Phaser 8510MFP Betriebsanleitung

Xerox

Xerox WorkCentre 7800 series Bedienungsanleitung

Xerox

Xerox VersaLink B605 Bedienungsanleitung

Xerox

Xerox VersaLink B71 Series Bedienerhandbuch

Xerox

Xerox Digital Color Press 700 Bedienungsanleitung

Xerox

Xerox WorkCentre Pro C2128 Bedienungsanleitung

Xerox

Xerox Phaser 6020 Bedienungsanleitung

Xerox

Xerox WorkCentre 5222 Betriebsanleitung

Xerox

Xerox WorkCentre 7232 Betriebsanleitung

Xerox

Xerox 3300MFP - Phaser B/W Laser Bedienungsanleitung

Xerox

Xerox Work Centre PE114e Bedienungsanleitung

Xerox

Xerox Phaser 3320 Bedienungsanleitung

Xerox

Xerox WorkCentre 6027 Betriebsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung