Xerox DocuColor 250 Montageanleitung

Andere Handbücher für DocuColor 250

2

Dieses Handbuch passt für folgende Modelle

6

Inhaltsverzeichnis

Andere Xerox Kopierer Handbücher

Xerox

Xerox Document Centre 230 Bedienungsanleitung

Xerox

Xerox C123 Copycentre Stücklistenhandbuch

Xerox

Xerox XC811 Bedienungsanleitung

Xerox

Xerox DocuColor 3535 Bedienungsanleitung

Xerox

Xerox Copycentre C118 Bedienungsanleitung

Xerox

Xerox CopyCentre C35 Bedienungsanleitung

Xerox

Xerox Wide Format 6204 Bedienungsanleitung

Xerox

Xerox CopyCentre 232 Handbuch

Xerox

Xerox 2006NPC - DocuColor Color Laser Bedienungsanleitung

Xerox

Xerox DocuColor DocuColor 4 Montageanleitung

Xerox

Xerox Document Centre 470cx Technisches Handbuch

Xerox

Xerox Legacy 4590 Bedienungsanleitung

Xerox

Xerox C123 Copycentre Bedienungsanleitung

Xerox

Xerox D95 Bedienungsanleitung

Xerox

Xerox Document Centre 50 Bedienungsanleitung

Xerox

Xerox 4595 Bedienungsanleitung

Xerox

Xerox DocuColor 5750 Bedienungsanleitung

Xerox

Xerox 5760 Bedienungsanleitung

Xerox

Xerox DocuColor 40 Bedienungsanleitung

Xerox

Xerox WorkCentre Pro 65 Bedienungsanleitung

Xerox

Xerox Copycentre C118 Bedienungsanleitung

Xerox

Xerox DOCUCOLOR 12 Bedienungsanleitung

Xerox

Xerox DOCUCOLOR 12 Handbuch

Xerox

Xerox C123 Copycentre Bedienungsanleitung

Beliebte Kopierer Handbücher anderer Marken

Canon

Canon iR1210 Referenzhandbuch

Ricoh

Ricoh FW740 Bedienungsanleitung

Minolta

Minolta CF910 Bedienungsanleitung

Ricoh

Ricoh B003 Bedienungsanleitung

Oce

Oce 9800 Bedienungsanleitung

Olivetti

Olivetti d-Copia 1800 Bedienungsanleitung

Minolta

Minolta Di181 Bedienungsanleitung

Canon

Canon iR5000i Bedienungsanleitung

Telecrane

Telecrane F25 Bedienungsanleitung

Canon

Canon NP6317 Anleitung zur Verwendung

Sharp

Sharp AR-5015 N Bedienungsanleitung

Ricoh

Ricoh Di-C1 Bedienungsanleitung

Mita

Mita MIP-2400 Handbuch

Sharp

Sharp AL-2061 Bedienungsanleitung

Muratec

Muratec MFX-C2280 Bedienungsanleitung

Ricoh

Ricoh FT5034C Bedienungsanleitung

Minolta

Minolta EP4000 Bedienungsanleitung

Ricoh

Ricoh V-C3 Installationsanleitung

701P44280

September 2005

1

Dear Customer:

This document contains directions for printing tabs using the DocuSP controller with the DocuColor 250,

2045, 2060, 5252, 6060, 7000, 8000 printers.

 At the printer:

1. Place tabs in appropriate Tray 3 (DocuColor 2045, 2060, 5252) or any tray (DocuColor 250,

6060, 8000).

• Tabs are short edge feed.

• Tabs face the back of the printer.

• The last tab of the set must be on top if the job is programmed as N to 1.

• Size: 9 X 11 inch.

• Weight: program with the correct weight.

• If the tabs are precut, be sure to program the tab sequence number, which is the number

of tabs in the set, not the number of tabs used. For example, if the tab set is 5 and only 3

tabs are being used, the tab sequence number is 5.

Example: Set up a job for seven tabs with the tab information included on the originals:

– Tab stock is typically purchased in sets of five tabs. For this job put aside the last

three tabs of bank two as they are not needed for this job.

– Pre-collate the tabs in the tray for every set by reversing the order of the tabs.

For this job tab 7 is on top, tab 6 is after that, tab 5 is next, tab 4, tab 3, tab 2, tab

1.

– Reverse Order would be for N to 1 job finishing, Otherwise 1 to N is Forward

Order.

Note: The tabs cannot just be pulled out of the box and flipped over because

they will be in the wrong sequence. Extra tabs can be saved for future jobs.

– Tabs do not run at rated printer speed because they are heavier stock.

– Use Manual job recovery if there is a jam. As jammed tabs are removed, replace

them in the paper tray in the proper order or the whole job will be thrown off.

Note: If the jammed tab is the furthest from the paper tray, it will have to be the

next tab fed by the printer.

2. Place 8.5 x 11 inch paper in a paper tray short edge feed. Note, the only 8.5x11 stock

loaded must be short edge feed.

 At the DocuSP, access the Printer Manager and follow these steps for setting tabs:

1. Select the “Stacking” tab.

701P44280

September 2005

2

2. Select “Settings”.

3. Disable “Collated Stacking”. If this is left on, an error message displays and the job cannot be

run.

4. Check the paper tray programming in the Printer Manager to make sure that the paper stock

programming matches the stock in the printer paper trays.

5. Access the Job Manager. Select the job and select Properties.

6. If running a Portrait orientation job, select the “Output” tab and set “Rotation” to 180 degrees.

 Use Exception Programming for tab pages with the tab information included in the original set:

1. Be sure to print out the whole job and make a note of where the tab master pages are

located. For example, page 4, page 10, page 21, page 26, page 35, page 41, page 51.

2. Enable “Image Shift” for every exception page. Since pages are loaded in the printer short

edge feed and the image is rotated, the shift would be set on the negative “Y” axis. For

example, –0.75.

3. Program the exception pages for 9 X 11inch paper, correct weight stock.

Note: Be sure to run a proof job to make sure that the programming is accurate.