Xerox 5400DX - Phaser B/W Laser Printer Bedienungsanleitung

XEROX®PHASER 5400

TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS

XEROX PHASER 5400 TONER CARTRIDGE

UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]

www.uninetimaging.com

First introduced in October 2001, the Phaser 5400 machine is based on a 40ppm, 1200dpi Fuji-Xerox laser printer engine.

This engine is capable of printing on 11” x 17” paper. The exact engine number is not known, but if Fuji-Xerox has kept with past

practices, it would be the XP-40 (40ppm). The cartridge itself (Xerox # 113R00495) is very easy to remanufacture, and with list

prices above $296.00 USD* per cartridge, a nice profit maker as well.

The cartridge is rated for 20,000 pages and is loaded with 820g of toner. A complete line of supplies is available for these

cartridges. These machines tend to be used as workgroup printers, so if you have a customer that has one, the cartridge volume

will be on the high side. While this cartridge looks very similar to the Lexmark W812 from the outside, it is very different. This is

especially true for the toner. It should also be noted that there is a chip, and it must be changed each cycle. The chip itself is an

RF type and is a black round disk that fits into the fill plug.

XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS

REMANUFACTURING THE XEROX

PHASER 5400 TONER CARTRIDGE

By Mike Josiah and the Technical Staff at UniNet

UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]

www.uninetimaging.com

The only real similarity to the Lexmark W812 is that they both use white plastic pins located on each side of the cartridge that

lock the two halves of the cartridge in place. The heads of these pins have what looks like a one way screw head on them

(see above photo). We have contacted multiple specialty screw manufacturers to see if a special tool is available, but were not

able to find one. They can be removed by inserting a 1” long #6 or #8 wood screw into the center of the pin. You can then twist

the pin and pull it out.

*Cartridge pricing as of June 2007

MACHINES BASED ON THE XEROX 5400 ENGINE:

Phaser 5400

Phaser 5400 N

Phaser 5400 DT

Phaser 5400 DX

How to run test prints as well as printer error codes will be discussed at the end of this article.

SUPPLIES REQUIRED:

1. New toner (820g) for use in Phaser 5400

2. New drum for use in Phaser 5400

3. Replacement cartridge pins

4. New replacement chip

5. New doctor blade (optional)

6. New magnetic roller sleeve (optional)

7. Sealing strip

8. Cotton swabs

9. Isopropyl alcohol

10. Drum padding powder

11. Conductive grease

12. Dedicated magnetic roller cleaner

TOOLS REQUIRED:

1. Phillips head screwdriver

2. Small common screwdriver

3. Needle nose pliers

4. Spring hook

5. Vacuum approved for toner

XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS

UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]

www.uninetimaging.com

1. Turn the cartridge so that the handle is towards you (spring on the right). On either side of the cartridge is a white plastic pin

with one way screw heads. These pins are what hold and lock both halves together. Specialty drivers to remove them are not

available (at the time of this writing) so the only way to remove them (at the time of this writing), is to insert a 1” long or

#8 woodscrew into the center of the pin. Pull/pry out to remove. Leave the screws in so they can easily be installed.

4. Remove the two screws and white plastic drum axle pin from

the single gear side of the drum.

5. Remove the drum.

XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS

UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]

www.uninetimaging.com

2. Remove the spring from the right side of the cartridge.

Separate the two halves.

3. Remove the two screws and metal drum axle pin from the

double gear side of the drum.

6. Remove the PCR from its holders. 7. Remove the two screws and wiper blade.

8. Clean out the waste chamber. Be very careful not to lose or

damage the foam wiper blade seal. This seal is very fragile and

a vacuum/compressed air cleaning system will damage it if

you are not careful.

9. Coat the wiper blade with your preferred lubricant, and

install in the cartridge. Install the two (gold)long screws, the

four short screws are for the drum axle pins only.

XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS

UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]

www.uninetimaging.com

10. Clean the PCR contacts with a cotton swab and alcohol. 11. Clean the PCR with your preferred PCR cleaner and install

in the holders.

12. Install the drum, axle pins, and screws. Make sure that the metal axle pin is on the double gear side, and the white plastic

pin is on the single gear side. Although the toner hopper can be cleaned and filled through the fill plug, it is recommended that

the magnetic roller be removed and cleaned. This will also be necessary to do once a seal is available. The fill plug has a black

cover in the center that is held on by double sided tape. This cover is actually the chip, which must be replaced for the cartridge

to work.

XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS

UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]

www.uninetimaging.com

13. With a small jeweler’s screwdriver, pry the black cover off

the fill plug.

14. With the pair of needle nose pliers, pull the fill plug out.

Grasp the plug by the small cross braces, and pull. This

method does not damage the plug seal. Dump out any remain-

ing toner from the hopper.

15. On the side opposite the fill plug, remove the two screws

and end cap.

16. Press in and lift up the locking tab on the right side of the

magnetic roller. With the keyed shaft of the magnetic roller

free, lift up on the keyed end by the locking tab. Pull the entire

magnetic roller assembly free.

XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS

UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]

www.uninetimaging.com

17. Remove the two screws and doctor blade.

Clean out any remaining toner.

18. Install the seal.

Make sure the seal tab is slid into the seal tab slot.

19. Install the cleaned doctor blade and two screws.

Be careful not to damage the alignment pins.

XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS

UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]

www.uninetimaging.com

20. Clean the magnetic roller assembly with a dedicated magnetic roller cleaner.

Install the assembly left side (round shaft) first.

Make sure the locking tab is firmly locked in place.

21. Install the end cap.

The gear posts must also align to the end cap holes.

Install the two screws.

22. Fill with 820g toner for Phaser 5400.

XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS

UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]

www.uninetimaging.com

23. Install the fill plug, check for leaks. If the round chip fell off,

just throw it away. A new chip will be installed later in the

instruction.

24. Install the toner supply section onto the waste chamber.

Make sure the spring on the supply hopper fits into the plastic

ring on the waste hopper.

25. Install the two white plastic locking pins. 26. Remove the two screws from the white pins.

XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS

UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]

www.uninetimaging.com

Andere Handbücher für 5400DX - Phaser B/W Laser Printer

Dieses Handbuch passt für folgende Modelle

Andere Xerox Druckerzubehör Handbücher

Xerox

Xerox ColorStix 8200 Ink Sticks Series s Bedienungsanleitung

Xerox

Xerox 097S03745 Handbuch

Xerox

Xerox Fiery color server Bedienungsanleitung

Xerox

Xerox 5500DN - Phaser B/W Laser Printer Bedienungsanleitung

Xerox

Xerox Phaser 6128 MFP Bedienungsanleitung

Xerox

Xerox 5500DN - Phaser B/W Laser Printer Bedienungsanleitung

Xerox

Xerox C11 - DocuPrint Color Inkjet Printer Bedienungsanleitung

Xerox

Xerox DocuPrint 2000MX Bedienungsanleitung

Xerox

Xerox 5500DN - Phaser B/W Laser Printer Bedienungsanleitung

Xerox

Xerox 3R11500 Bedienungsanleitung

Xerox

Xerox WorkCentre 118 Bedienungsanleitung

Xerox

Xerox Document WorkCentre 450c Bedienungsanleitung

Xerox

Xerox Phaser 5335 Bedienungsanleitung

Xerox

Xerox Phaser 6180MFP Bedienungsanleitung

Xerox

Xerox WorkCentre 4265 Betriebsanleitung

Xerox

Xerox Phaser 6128 MFP Bedienungsanleitung

Xerox

Xerox C11 - DocuPrint Color Inkjet Printer Bedienungsanleitung

Xerox

Xerox Instant Print Kiosk Bedienungsanleitung

Xerox

Xerox 7500DX - Phaser Color LED Printer Bedienungsanleitung

Xerox

Xerox SquareFold Trimmer Module Bedienungsanleitung

Xerox

Xerox C11 - DocuPrint Color Inkjet Printer Bedienungsanleitung

Xerox

Xerox 3600B - Phaser B/W Laser Printer Konfigurationshandbuch

Xerox

Xerox 6130N - Phaser Color Laser Printer Bedienungsanleitung

Xerox

Xerox Versant 4100 Press Bedienungsanleitung

Beliebte Druckerzubehör Handbücher anderer Marken

Star Micronics

Star Micronics TSP800 Series Bedienungsanleitung

REA

REA JET HR pro 2K Bedienungsanleitung

HP Laserjet,Color Laserjet 4si Bedienungsanleitung

oliser

oliser MS 45 Bedienungsanleitung

Roland

Roland DU2-64 Anleitungen und Rezepte

Canon

Canon Finisher-T1 Bedienungsanleitung

Sharp

Sharp FO-1MK Bedienungsanleitung

Labelmate

Labelmate PM-300 Bedienungsanleitung

Epson

Epson T6248 Betriebsanleitung

Epson

Epson OT-BZ20 Bedienungsanleitung

Canon

Canon TonerRobot EP-27 Bedienungsanleitung

Ricoh

Ricoh LCIT RT5100 Kurzanleitung

GBC

GBC 16 Series Bedienungsanleitung

Canon

Canon INNER 2-WAY TRAY-E1 Bedienungs- und Wartungshandbuch

Develop

Develop SD-509 Bedienungsanleitung

Kyocera

Kyocera KM-6230 Handbuch

Triumph Adler

Triumph Adler DF-710 Handbuch

Citizen

Citizen CBM-202PC Series Bedienungsanleitung