Xerox 3450B - Phaser B/W Laser Printer Bedienungsanleitung

Service

Manual

Phaser

™

Laser Printer

3450

Phaser3450 Laser Printer

Service Manual

Warning

The following servicing instructions are for use by qualified service

personnel only. To avoid personal injury, do not perform any servicing other

than that contained in the operating instructions, unless you are qualified to

do so.

First Printing: July, 2003

071-0866-00

Service Manual iii

Service Terms

Manual Terms

Various terms are used throughout this manual to either provide additional

information on a specific topic or to warn of possible danger present during a

procedure or action. Be aware of all symbols and terms when they are used, and

always read NOTE, CAUTION, and WARNING statements.

Common Acronyms:

The following list defines the acronyms that may be found in this manual.

Note

A note indicates an operating or maintenance procedure, practice or condition

that is neccessary to efficiently accomplish a task. A note can provide additional

information related to a specific subject or add a comment on the results achieved

through a previous action.

Caution

A caution statement indicates an operating or maintenance procedure, practice or

condition that, if not strictly observed, could result in damage to, or destruction

of, equipment.

Warning

A warning statement indicates an operating or maintenance procedure, practice

or condition that, if not strictly observed, could result in injury or loss of life.

Product Terms

Caution: A personal injury hazard exists that may not be apparent. For example, a

panel may cover the hazardous area.

Danger: A personal injury hazard exists in the area where you see the sign.

ADC: Automatic Density Control NCS: Non-Contact Sensor

BTR: Bias Transfer Roller PHD: Imaging Unit

CRUM: Customer Replaceable Unit Monitor PL: FRU Parts List.

CTD: Toner Density Control PTL: Pre-Transfer Lamp

DRV: Motor Driver Board RMI: Routine Maintenance Item

ESD: Electrostatic Discharge RMS: Root-Mean-Square

LSU: Laser Scanning Unit RTC: Charge Roller

MCU: Engine Control Board

iv Phaser 3450 Laser Printer

Symbols Marked on the Product

DANGER high voltage.

Protective ground (earth) symbol.

Hot surface on or in the printer. Use caution to avoid personal

injury.

The surface is hot while the printer is running. After turning off

the power, wait 30 minutes.

Avoid pinching fingers in the printer. Use caution to avoid

personal injury.

Use caution (or draws attention to a particular component).

Refer to the manual(s) for information.

30 min.

Service Manual v

Power Safety Precautions

Power Source

For 110 VAC printers, do not apply more than 140 volts RMS between the supply

conductors or between either supply conductor and ground. Use only the specified

power cord and connector. For 220 VAC printers, do not apply more than 264 volts

RMS between the supply conductors or between either supply conductor and ground.

Use only the specified power cord. This manual assumes that the reader is a qualified

service technician.

Plug the three-wire power cord (with grounding prong) into a grounded AC outlet

only. If necessary, contact a licensed electrician to install a properly grounded outlet.

If the product loses its ground connection, contact with conductive parts may cause an

electrical shock.

Disconnecting Power

Turning the power off using the On/Off switch does not completely de-engergize the

printer. You must also disconnect the printer power cord from the AC outlet. Position

the power cord so that it is easily accessible during servicing so that you may power

down the printer during an emergency.

Disconnect the power plug by pulling the plug, not the cord.

Disconnect the power cord in the following cases:

■if the power cord or plug is frayed or otherwise damaged,

■if any liquid or foreign material is spilled into the case,

■if the printer is exposed to any excess moisture,

■if the printer is dropped or damaged,

■if you suspect that the product needs servicing or repair,

■whenever you clean the product.

vi Phaser 3450 Laser Printer

Electrostatic Discharge (ESD) Precautions

Some semiconductor components, and the respective sub-assemblies that contain

them, are vulnerable to damage by Electrostatic discharge (ESD). These components

include Integrated Circuits (ICs), Large-Scale Integrated circuits (LSIs), field-effect

transistors and other semiconductor chip components. The following techniques will

reduce the occurrence of component damage caused by static electricity.

Be sure the power to the chassis or circuit board is off, and observe all other safety

precautions.

■Before handling any semiconductor components assemblies, drain the

electrostatic charge from your body. This can be accomplished by touching an

earth ground source or by wearing a wrist strap device connected to an earth

ground source. Wearing a wrist strap will also prevent accumulation of additional

bodily static charges. Be sure to remove the wrist strap before applying power to

the unit to avoid potential shock.

■After removing a static sensitive assembly from its anti-static bag, place it on a

grounded conductive surface. If the anti-static bag is conductive, you may ground

the bag and use it as a conductive surface.

■Do not use freon-propelled chemicals, as they can generate electrical charges that

may damage some devices.

■Do not remove a static sensitive replacement component or electrical sub-

assembly from its protective package until you are ready to install it.

■Before removing the protective material from the leads of a replacement device,

touch the protective material to the chassis or circuit assembly into which the

device will be installed.

■Minimize body motions when handling unpackaged replacement devices. Simple

motions such as your clothes brushing together or lifting a foot from a carpeted

floor can generate enough static electricity to damage a static sensitive device

■Handle IC’s and EPROM’s carefully to avoid bending pins.

■Pay attention to the direction of parts when mounting or inserting them on

Printed Circuit Boards (PCB’s).

Service Manual vii

Service Safety Summary

General Guidelines

Note

The material presented here is intended as a safety reminder for qualified service

personnel. Refer also to the preceding Power Safety Precautions.

Avoid servicing alone: Do not perform internal service or adjustment of this

product unless another person capable of rendering first aid or resuscitation is present.

Use care when servicing with power: Dangerous voltages may exist at several

points in this product. To avoid personal injury, do not touch exposed connections and

components while power is on. Disconnect power before removing the power supply

shield or replacing components.

Do not wear jewelry: Remove jewelry prior to servicing. Rings, necklaces and

other metallic objects could come into contact with dangerous voltages and currents.

Power source: This product is intended to operate from a power source that will

not apply more then 264 volts rms for a 220 volt AC outlet or 140 volts rms for a 110

volt AC outlet between the supply conductors or between either supply conductor and

ground. A protective ground connection by way of the grounding conductor in the

power cord is essential for safe operation.

Warning Labels

Read and obey all posted warning labels. Warning labels are displayed on potentially

dangerous printer components. As you service the printer, check to make certain that

all warning labels remain in place.

Safety Interlocks

Make sure all covers and the printer’s front panel are in place and all interlock

switches are functioning correctly after you have completed a printer service call. If

you bypass an interlock switch during a service call, use extreme caution when

working on or around the printer.

CLASS 1 LASER PRODUCT

The Phaser3450 Laser Printer is certified to comply with Laser Product

Performance Standards set by the U.S. Department of Health and Human Services as

a Class 1 Laser Product. This means that this is a class of laser product that does not

emit hazardous laser radiation; this is possible only because the laser beam is totally

enclosed during all modes of customer operation. The laser is not hazardous during

servicing if you follow the procedures specified in the manual.

viii Phaser 3450 Laser Printer

Servicing Electrical Components

Before starting any service procedure, switch off the printer power and unplug the

power cord from the wall outlet. If you must service the printer with power applied,

be aware of the potential for electrical shock.

Warning

Turning the power off by using the On/Off switch does not completely de-

energize the printer. You must also disconnect the printer power cord from the

AC outlet. Position the power cord so that it is easily accessible during servicing.

Warning

Do not touch any electrical component unless you are instructed to do so by a

service procedure.

Servicing Mechanical Components

When servicing mechanical components within the printer, manually rotate drive

assemblies, rollers, and gears.

Warning

Do not try to manually rotate or manually stop the drive assemblies while any

printer motor is running.

Servicing Fuser Components

Warning

This printer uses heat to fuse the toner image to media. The Fuser Assembly is

VERY HOT. Turn the printer power off and wait at least 5 minutes for the Fuser

to cool before you attempt to service the Fuser Assembly or adjacent

components.

S7300-0

Service Manual ix

Regulatory Specifications

Federal Communications Compliance

The equipment described in this manual generates and uses radio frequency energy. If

it is not installed properly in strict accordance with Xerox instructions, it may cause

interference with radio and television reception or may not function properly due to

interference from another device. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

■Reorient or relocate the receiver (device being interfered with).

■Increase the separation between the printer and the receiver.

■Connect the printer into an outlet on a different circuit than the receiver.

■Route the interface cables on the printer away from the receiver

■Consult the dealer, Xerox service, or an experienced radio/television

technician for help.

Changes or modifications not expressly approved by Xerox can affect the emission

and immunity compliance and could void the user's authority to operate this product.

To ensure compliance, use shielded interface cables. A shielded parallel cable can be

purchased directly from Xerox at www.xerox.com/office/supplies.

Xerox has tested this product to internationally accepted electromagnetic emission

and immunity standards. These standards are designed to mitigate interference caused

or received by this product in a normal office environment. This product is also

suitable for use in a residential environment based on the levels tested.

In the United States this product complies with the requirements of an unintentional

radiator in part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference; (2) this device must

accept any interference received, including interference that may cause undesired

operation.

This digital apparatus does not exceed the Class B limits for radio noise emissions

from digital apparatus set out in the Radio Interference Regulations of the Canadian

Department of Communications, ICES-003.

Le présent appareil numérique n'émet pas de bruits radioélectrique dépassant les

limits applicables aux appareils numériques de la classe B prescrites dans le

Réglement sur le brouillage radioélectrique édicté par le ministere des

Communications du Canada, NMB-003.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Xerox Drucker Handbücher

Xerox

Xerox PHASER 7500 Bedienungsanleitung

Xerox

Xerox Phaser 6700DN Bedienungsanleitung

Xerox

Xerox DocuColor 5252 Bedienungsanleitung

Xerox

Xerox WorkCentre 4260 Series Bedienungsanleitung

Xerox

Xerox N2125N - DocuPrint B/W Laser Printer Bedienungsanleitung

Xerox

Xerox Phaser 6280 Bedienungsanleitung

Xerox

Xerox 7700 Bedienungsanleitung

Xerox

Xerox VersaLink B600 Bedienungsanleitung

Xerox

Xerox Phaser 8560 Bedienungsanleitung

Xerox

Xerox 4018 Bedienungsanleitung

Xerox

Xerox Nuvera 100 Montageanleitung

Xerox

Xerox Phaser 7760 Betriebsanleitung

Xerox

Xerox Docuprint 75 Technisches Handbuch

Xerox

Xerox 3500B - Phaser B/W Laser Printer Bedienungsanleitung

Xerox

Xerox DocuColor 2060 Betriebsanleitung

Xerox

Xerox PHASER 6250 Betriebsanleitung

Xerox

Xerox DocuPrint C2255 Bedienungsanleitung

Xerox

Xerox Color 1000 Press Bedienungsanleitung

Xerox

Xerox DocuPrint N17 Handbuch

Xerox

Xerox VersaLink C600 Bedienungsanleitung

Xerox

Xerox DocuColor 2060 Technisches Handbuch

Xerox

Xerox PHASER 6250 Programmierhandbuch

Xerox

Xerox Phaser 6250DT Bedienungsanleitung

Xerox

Xerox Phaser 6120 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung

Lexmark

Lexmark Infoprint 1332 Bedienungsanleitung