Xerox Phaser 4 400 Montageanleitung

Phaser™4400 Laser Printer

Windows NT 4.x Network

This section provides installation and troubleshooting steps for Windows NT 4.x:

■Preliminary steps —see page 17.

■Quick CD-ROM install steps —see page 17.

■Other methods of installation —see page 18.

■Windows NT 4.x troubleshooting (TCP/IP) —see page 21.

■Windows NT 4.x troubleshooting (AppleTalk) —see page 22.

Preliminary steps

The preliminary steps given below must be accomplished for all printers regardless of the method that is

being used.

1. Verify that the printer is plugged in, turned on, and connected to an active network.

2. Verify that the printer is receiving network traffic by monitoring the LED’s on the back of the

printer or on the CentreDirect External Print Server. When the printer is connected to a

functioning network receiving traffic, its link LED is green, and its traffic LED (amber) is flashing

rapidly.

3. Print the Configuration Pages and retain them for reference. For information on using the front

panel or printing Configuration Pages, refer to the Front Panel section of the Features Guide of

the Interactive Documentation CD-ROM.

4. Check the Configuration Pages and verify that the desired protocol is enabled.

5. Proceed to the Quick CD-ROM install steps or Other methods of installation section for the

installation method desired.

Quick CD-ROM install steps

1. Insert your printer’s Printer Installer and Utilities CD-ROM into your computer’s CD-ROM

drive. If your PC is set to autorun, a Xerox installer should automatically start. If it does not start,

do the following:

a. Click Start and Run.

b. In the Run window, type: <CD drive>:\INSTALL.EXE.

2. Select your desired language from the list.

3. Install the printer drivers for your printer. Within the Xerox installer, select Printer Drivers, and

then select Install Xerox Phaser 4400 Laser Printer Drivers.

4. Click Yes to accept the Xerox Software License Agreement.

5. The Xerox installer searches the network and displays the first printer found. Click Next to accept

this printer.

Windows NT 4.x Network

Phaser™4400 Laser Printer 18

6. Click Next to accept the printer’s default name or enter an alternate name, and then click Save

Changes before clicking Next.

7. The information dialog box displays the files to be copied to your system. Click Next to install the

files and Finish to complete the installation.

Other methods of installation

Your printer can also be installed on a Windows NT network using one of these methods:

■Microsoft TCP/IP protocol

■AppleTalk protocol

■The CentreWare IS program on your Advanced Printer Management Tools CD-ROM can also

be used to monitor and configure the printer. If your printer is connected to a Windows NT

network with the TCP/IP protocol enabled, you can use a web browser to monitor and configure

your printer through CentreWare IS.

■For installing or managing multiple printers on a Windows NT network with the TCP/IP protocol

enabled, you can use the Xerox CentreWare MC snap-in to Microsoft Management Console. Refer

to the Xerox CentreWare MC User Guide on the Advanced Printer Management Tools

CD-ROM.

■You can use Xerox TCP/IP Port Monitor to add or remove TCP/IP ports for installations using the

PCL driver.

Quick install steps (Microsoft TCP/IP protocol)

1. At the Desktop, right-mouse-click the Network Neighborhood icon and select Properties.

2. Click on the Protocols tab and verify that the TCP/IP protocol has been loaded.

3. Select the Services tab and verify that Microsoft TCP/IP Printing is loaded.

4. If this software is not present, install it using the documentation provided by Microsoft, and then

return to this document.

5. Open the Control Panel and double-click the Printers icon.

6. Double-click Add Printer; the Add Printer Wizard starts.

7. Verify that My Computer is selected and click Next>.

8. Click Add Port.

9. From the list that appears, select LPR Port.

10. Click New Port. This opens up the Add LPR compatible printer window.

11. Type the IP address of your printer and a printer name of up to 31 characters (no spaces).

12. Select OK. The Wizard returns you to the previous dialog. Verify that the new IP address you

entered is in the list and is correct. The check box to the left of the address must be checked; if it is

not, check it, and then select Next>.

13. Insert your printer’s Printer Installer and Utilities CD-ROM into your computer’s CD-ROM

drive and click Have Disk.

14. Click the Browse button and select the directory containing the Windows NT drivers.

15. Select the *.INF file.

Windows NT 4.x Network

Phaser™4400 Laser Printer 19

16. Click Open. The Wizard returns you to the previous dialog. Verify that the path and filename are

correct and click OK.

17. At the next dialog, enter a name for the printer and select whether you want that printer to be the

default. Click Next>.

18. If the printer is not shared, click Next>. To share the printer, enter a Share Name, check the share

checkbox, and then click Next>.

19. At the next dialog, it is recommended that you print a test print. Click Finish.

20. Wait for the test print to print. A new dialog asks for confirmation of the test print; click Yes.

21. Send a print job to the printer.

22. Check the print job for print-quality. If print-quality problems exist or if your job did not print,

refer to the Troubleshooting Guide on the Interactive Documentation CD-ROM to correct the

problem or access PhaserSMART from the Troubleshooting tab of your Windows driver.

Quick install steps (AppleTalk protocol)

Note

Services for Macintosh must be installed for AppleTalk to be available on an NT 4.x server.

1. At the Desktop, right-mouse-click the Network Neighborhood icon and select Properties.

2. Click the Protocolstab and verify that the AppleTalk protocol has been loaded.

3. If the AppleTalk software is not present, install it using the documentation provided by Microsoft,

and then return to this document.

4. Open the Control Panel and double-click the Printers icon.

5. Double-click Add Printer; the Add Printer Wizard starts.

6. Verify that My Computer is selected and click Next>.

7. Click Add Port.

8. Select the AppleTalk Printing Devices and click New Port.

9. Click Ethernet and select the device.

10. Choose your printer device from the list, then click OK.

11. Click OK. The Wizard returns you to the previous dialog. Verify that the port name you entered is

in the list and is correct. The check box to the left of the port name must be checked; if it is not,

check it, and then select Next>.

12. Insert your printer’s Printer Installer and Utilities CD-ROM into your computer’s CD-ROM

drive and click Have Disk.

13. Click the Browse button and select the directory containing the Windows NT drivers:

<CD Drive>:\instal\winnt40, and then click Open.

14. Select the *.INF file, then click OK.

15. The Wizard returns you to the previous dialog. Verify that the path and file name are correct and

click OK.

16. At the next dialog, enter a name for the printer and select whether you want that printer to be the

default, and then click Next>.

Windows NT 4.x Network

Phaser™4400 Laser Printer 20

17. If the printer is not shared, click Next>. To share the printer, enter a Share Name, check the share

checkbox, and then click Next>.

18. At the next dialog it is recommended that you print a test print. Click Finish.

19. Wait for the test print to print. A new dialog asks for confirmation of the test print; click Yes.

20. Send a print job to the printer.

21. Check the print job for print-quality. If print-quality problems exist or if your job did not print,

refer to the Troubleshooting Guide on the Interactive Documentation CD-ROM to correct the

problem or access PhaserSMART from the Troubleshooting tab of your printer driver.

Xerox TCP/IP Port Monitor

The Xerox installer for Windows automatically installs Xerox TCP/IP Port Monitor for those

installations using the PCL driver. The Xerox TCP/IP Port Monitor can be used to add or remove TCP/

IP ports.

Adding a port using Xerox TCP/IP Port Monitor

1. To add a TCP/IP port, open the Printer Properties dialog box for the printer you would like to

attach the new TCP/IP port.

a. Click Start, scroll to Settings, and click Printers.

b. Click your right-mouse button on the printer to which you want to attach the new TCP/IP

port, and select Properties.

2. Select the Details tab, and click the Add Port button.

3. In the Add Port dialog box, select Other.

4. From the list of available printer port monitors, select the Xerox TCP/IP Port, and then click the

OK button.

5. At this point, you enter the Xerox TCP/IP Printer Port Wizard. The wizard guides you step-by-

step through the following procedures:

a. Choosing a name for the new port.

b. Identifying a printer by its DNS Name or IP Address.

c. (Alternatively) Identifying a printer using the automatic Printer Discovery feature. Click

Next to proceed with the port installation.

6. The wizard verifies the port name and printer address, and automatically configures the remaining

port settings for you. Any errors detected in printer identification displays a dialog box requesting

Additional Information. In the Add Xerox TCP/IP Port window:

a. Under Enter a Port Name, enter a unique name for the port being added.

b. Under Enter a printer name or IP address, enter the printer’s host name or IP Address.

c. Click Next.

Note

To locate Xerox printers on your local area network, select Auto Printer Discovery, and

then click Refresh. The Xerox TCP/IP Port Monitor searches the network for Xerox printers

and displays them in a list. Select your desired printer from the list and click OK.

Windows NT 4.x Network

Phaser™4400 Laser Printer 21

7. After all the port settings have been configured and verified, a Completing dialog box appears

summarizing all of the settings. You have the opportunity to change any of the settings by clicking

the Back key. Otherwise, click the Finish key to complete the port setup.

8. Click OK to exit from Printer Properties. This completes the installation of the Xerox TCP/IP

Port.

Windows NT 4.x troubleshooting (TCP/IP)

This troubleshooting section assumes you have completed the following tasks:

■You have loaded a Phaser printer PCL or PostScript print driver.

■You have printed and retained a current copy of the Configuration Pages. For information on

printing Configuration Pages, refer to the Front Panel section of the Features Guide on the

Interactive Documentation CD-ROM.

1. Verify these items in the TCP/IP area of the Configuration Pages:

■IP Address Source is set to DHCP, Front Panel, BOOTP, or Auto IP (depending on your

network configuration).

■Current IP Address is set correctly. (Note this address if it is assigned by Auto IP, DHCP, or

BOOTP.)

■Subnet Mask is set correctly (if used).

■Default Gateway is set correctly (if used).

The LPR setting must be enabled. Check the LPR and AppSocket settings and verify they are set

as desired.

2. Verify the Language in the LPR area of the Configuration Pages:

■Interpreters: Auto, PCL or PostScript (depending on your driver).

3. Verify that the client is logged into the network and printing to the correct print queue. Also verify

that the user has access to the Phaser printer queue.

4. From the server desktop, use the right-mouse button to click on Network Neighborhood. With

the left-mouse button, select Properties from the cascade menu.

5. The Network dialog should appear. Select the Protocols tab.

6. Check the list of installed network protocols for TCP/IP Protocol.

7. As required, click Add and install any components not listed and restart the system.

8. Once rebooted, click on Start, select Settings, select Control Panel, and double-click on

Services. Find TCP/IP PrintServer. Verify that the Status column reads “Started”and the Startup

column reads “automatic”.

9. Select the Start button and Settings, then select the Printers folder. The Printers window should

appear.

10. Right-mouse-click on the printer icon and select Properties.

11. Verify that you have loaded and selected the correct driver for your printer.

12. Select the Ports tab.

Windows NT 4.x Network

Phaser™4400 Laser Printer 22

13. Verify that the IP Address in the Print to the following port list is the same as the one from the

Configuration Pages. If necessary, re-select the TCP/IP number used for your printer.

14. Click on the General tab, then click Print Test Page. If the printer still does not print, access

PhaserSMART from the Troubleshooting tab of your printer driver or refer to the Xerox web site

at: www.xerox.com/officeprinting/support.

Windows NT 4.x troubleshooting (AppleTalk)

This troubleshooting section assumes you have completed the following tasks:

■You have loaded a Phaser printer PostScript print driver.

■You have printed and retained a current copy of the Configuration Pages. For information on

printing Configuration Pages, refer to the Front Panel section of the Features Guide on the

Interactive Documentation CD-ROM.

1. Verify these items in the EtherTalk areas of the Configuration Pages:

■The EtherTalk Name is correct.

■Enabled is set to Yes.

■Zone contains the desired zone name or * (* = means default local zone).

2. Verify that the client is logged into the network and printing to the correct print queue. Also verify

that the user has access to the Phaser printer queue.

3. From the server desktop, use the right-mouse button and select Network Neighborhood. With the

left-mouse button, select Properties from the cascade menu.

4. The Network dialog should appear. Select the Configuration tab.

5. Check the list of installed network components for AppleTalk Protocol.

6. As required, install any components not listed and restart the system.

7. Once rebooted, select the Start button and Settings, then select the Printers folder. The Printers

window should appear.

8. Right-mouse-click on the printer icon and select Properties.

9. Verify that you have selected the correct driver for your printer.

10. Select the Ports tab.

11. Verify the AppleTalk name in the Print to the following port list. If necessary, re-select the

correct name or, if not listed, Add a new port, selecting the Zone, then the name, from Steps 1 and

2 above.

12. Click on the General tab, then click Print Test Page. If the printer still does not print, access

PhaserSMART from the Troubleshooting tab of your printer driver or refer to the Xerox web site

at: www.xerox.com/officeprinting/support.

Andere Handbücher für Phaser 4 400

Inhaltsverzeichnis

Andere Xerox Drucker Handbücher

Xerox

Xerox 3107 Bedienungsanleitung

Xerox

Xerox FS-C8008DN Bedienungsanleitung

Xerox

Xerox PHASER 6250 Leitfaden

Xerox

Xerox 8860MFPD - Multifunction Inkjet Printer Bedienungsanleitung

Xerox

Xerox Phaser 3610 Gebrauchsanweisung

Xerox

Xerox DocuPrint C6 Bedienungsanleitung

Xerox

Xerox Phaser 3610 Betriebsanleitung

Xerox

Xerox DocuColor 5252 Stücklistenhandbuch

Xerox

Xerox Phaser 8560 Installations- und Benutzerhandbuch

Xerox

Xerox 7400DN - Phaser Color LED Printer Bedienungsanleitung

Xerox

Xerox Phaser 8550 Bedienungsanleitung

Xerox

Xerox Phaser 6700DN Bedienungsanleitung

Xerox

Xerox 4050 Bedienungsanleitung

Xerox

Xerox Color C75 Press Bedienungsanleitung

Xerox

Xerox I Class Bedienungsanleitung

Xerox

Xerox DocuPrint C621 Bedienungsanleitung

Xerox

Xerox PHASER Phaser 4400 Kurzanleitung

Xerox

Xerox DocuPrint C1618 Bedienungsanleitung

Xerox

Xerox Phaser 3010 Bedienungsanleitung

Xerox

Xerox Nuvera 100 Montageanleitung

Xerox

Xerox Phaser 7300B Bedienungsanleitung

Xerox

Xerox Phaser EX7750 Bedienungsanleitung

Xerox

Xerox 8400N - Phaser Color Solid Ink Printer Bedienungsanleitung

Xerox

Xerox Phase 6200 Technische Daten

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung

Lexmark

Lexmark Infoprint 1332 Bedienungsanleitung