Xerox Synergix 8825 Bedienungsanleitung

Transmittal Page

Product

8825/8830Printer

Title

Service Manual

Part Number

701P15051

Status

SUPERSEDES

Replaces 701P15050 dated May 1999

Date

January 2002

8825/ 8830 Printer

Service Manual

THE DOCUMENT COMPANY

XEROX

CAUTION

Certain components in the 8825/ 8830 Printer are

susceptible to damagefrom electrostatic dis-

charge. Observe all ESD procedures to avoid com-

ponent damage.

701P15051

January 2002

Prepared by:

Xerox Corporation

800 Phillips Road

Bldg. 845-17S

Webster, New York 14580-9791

USA

Xerox®, XES®, AccXES®, and The Document Company®

are trademarks of Xerox Corporation.

Xerox product names mentioned in this publication are trademarks of the

XEROX CORPORATION.

NOTICE

While every care has been taken in the preparation of this manual, no liabil-

ity will be accepted by Xerox Corporation arising out of any inaccuracies or

omissions. NOTICE

All service documentation is supplied to Xerox external customers for infor-

mational purposes only. Xerox service documentation is intended for use by

certified product trained service personal only. Xerox does not warrant or

represent that such documentation is complete, nor does Xerox represent

or warrant that it will notify or provide to such customer any future changes

to this documentation. Customer performed service of equipment, or mod-

ules, components or parts of such equipment may affect the warranty

offered by Xerox with respect to such equipment. You should consult the

applicable warranty for its terms regarding customer or third party provided

service. If the customer services such equipment, modules, components or

parts thereof, the customer releases Xerox from any and all liability for the

customer actions, and the customer agrees to indemnify, defend and hold

Xerox harmless from any third party claims which arise directly or indirectly

from such service.

01/02

8825/8830 Printer

Introduction

About this Manual ........................................................................................................... iii

Organization....................................................................................................................iii

How to Use This Manual................................................................................................. iv

Repair Analysis Procedures (RAPs) ............................................................................... v

Repair / Adjustment Procedures ..................................................................................... v

01/02

ii 8825/8830 Printer

Introduction

01/02

iii

8825/8830 Printer About this Manual, Organization

Introduction

About this Manual

This manual is part of a documentation system that includes the training.

This manual contains Repair Analysis Procedures (RAPs), Repair Procedures, Adjustment

Procedures, Parts List, Diagnostic Procedures, Installation Procedures, Wiring Data and

BSDs.

This manual will enable the Service Representative to repair the 8825/8830 printers. Those

service procedures affected by the 8825 configuration differences will be identified using the

8825 product name or Tag number.

Organization

This manual consists of eight sections. The title and description of each section are listed

below.

Section 1. - Service Call Procedures

This section contains the following:

•Call Flow Procedure

•Initial Actions/ System Checks

•Print Defect Isolation Procedure

•Workstation Checkout Procedure

•Status Code Entry Chart

•Message Display Entry Chart

•Maintenance Procedures

•Callback

•System Checkout/ Final Action

Call Flow Procedure

The Call Flow Procedure is a list of activities to be performed on each service call.

Initial Actions/ System Checks

This procedure is designed to identify and classify the problem and to refer you to the appropri-

ate RAP in order to repair the problem. When the problem has been repaired, perform the Final

Action.

Print Defect Isolation Procedure

This procedure directs the CSE to make test prints, perform test procedures to identify the

cause of a print defect.

Workstation Checkout Procedure

This procedure is designed to ensure that the printer is correctly set up to run and communi-

cate with other elements. It consists of a series of connection checks, configuration test prints,

PING tests, and tests made from a laptop PC.

Status Code Entry Chart

This table provides a list of status codes, a description of the problem, the components that

are affected, RAPs that may resolve the problem, as wellas BSD references and Parts List ref-

erences.

Message Display Entry Chart

This table contains a list of messages that may be generated by the printer, their cause, clear-

ance procedures, and BSD references.

Maintenance Procedures

The Maintenance Procedures identifies functional checks and cleaning operations that must

be performed on every Normal Call. It also identifies those activities that can be performed as

needed or as scheduled.

01/02

iv 8825/8830 Printer

Organization, How to Use This Manual

Introduction

Callback

This service is performed when the CSE has been called back to correct a problem that was

thought to have been recently corrected. The Callback is a short procedure performed on only

that subsystem that caused the original service cal

System Checkout / Final Action

This procedure is used to verify that the printer is operating correctly after a repair, and that the

correct steps are taken to close out a service call.

Section 2. - Repair Analysis Procedures (RAPs)

This section contains the Repair Analysis Procedures (RAPs) necessary to repair the faults.

When using a RAP, always exit the procedure when the fault is fixed. Do not perform the

remaining steps.

Section 3. - Image Quality Repair Analysis Procedures (RAPs)

This section contains the Repair Analysis Procedures (RAPs) necessary to repair the image

quality faults. Refer to "How to Use the Image Defect Definitions" to compare the image defect

to the definitions. Once you have determined the definition that best describes the defect, go to

the section contents page to find the appropriate RAP. When using a RAP, always exit the pro-

cedure when the fault is fixed. Do not perform the remaining steps.

Section 4. - Repair / Adjustment

This section contains the repair and adjustment procedures for the 8825/8830 printers.

Section 5. - Parts List

This section contains the detailed Parts List for the 8825/8830 printers.

Section 6. - General Procedures

This section contains Diagnostic Procedures, Installation Procedures, and General Informa-

tion, which includes Product Specifications for the 8825/8830 printers.

Section 7. - Wiring Data

This section contains the BSDs.

How to Use This Manual

The Service Call Procedures will direct you to the appropriate Section of the Service Manual.

You should begin the service call with the Initial Actions/ System Checks Procedure. From

there, you will be referred to either Section 2, Status Indicator RAPs, Section 3, Image Quality

RAPs, or Section 7 BSDs.

If you are sent to Section 3, compare the image defect to the print quality definitions. Once you

have determined the definition that best describes the copy defect, go to the section contents.

The section contents will direct you to an image quality RAP. The RAP has a list of probable

causes and corrective actions. From these RAPs you may be referred to other sections of the

manual to make checks, Adjustments, or to replace parts.

When you have made a Repair, always go to the Call Flow Procedure to finish the call.

01/02

8825/8830 Printer

Introduction

Repair Analysis Procedures (RAPs)

A RAP is either a table of faults and possible solutions, or a series of steps designed to lead

you to the cause of a problem. In each step, you will perform an action or observe an occur-

rence. For fault tree RAPS, at each step, a statement is made that has a Yes (Y) or No (N)

answer.

If the answer is NO, perform the action following the NO. If the answer is YES, proceed to the

next step.

When several items are listed, perform them in the order listed.

Proceed through the steps only until the observed problem is isolated and solved. Then evalu-

ate the unit for proper performance. If a further defect is observed, go to the appropriate RAP

and perform the steps it contains until the additional fault is located and repaired.

Repair / Adjustment Procedures

The repair procedures provide detailed steps on how to remove and replace components. The

adjustment procedures provide detailed steps on how to check and adjust components. Some

units have been modified by various design changes. Each change or modification is labeled

with a Tag/ MOD (modification) number. The Tag/ MOD numbers are identified in the Change

Tag/ MOD Index inSection 6 of this Service Manual.

When a modification affects how a particular procedure is performed, the procedure or steps

are identified with either a W/ Tag/ MOD or a W/ O Tag/ MOD statement. Each procedure or

step that is affected by a modification is identified with the statement, W/ Tag/ MOD, followed

by the modification number. The W/ in the statement indicates that this step must be per-

formed on units thatare assembled with that specific modification.

When the procedure or steps are not affected by a particular modification, they are identified

with the statement, W/ O Tag/ MOD, followed by the modification number. The W/ O in the

statement indicates that this step must be performed on units assembled without that specific

modification.

01/02

vi 8825/8830 Printer

Introduction

Andere Handbücher für Synergix 8825

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Xerox Drucker Handbücher

Xerox

Xerox Phaser 7300 Montageanleitung

Xerox

Xerox 6130N - Phaser Color Laser Printer Bedienungsanleitung

Xerox

Xerox DocuPrint C525 A-AP Bedienungsanleitung

Xerox

Xerox VersaLink C620 Bedienungsanleitung

Xerox

Xerox Phaser 8200 Bedienungsanleitung

Xerox

Xerox Versant 80 Press Bedienungsanleitung

Xerox

Xerox 2135DX - Phaser Color Laser Printer Bedienungsanleitung

Xerox

Xerox Phaser 7800 Bedienungsanleitung

Xerox

Xerox Phaser 8200 Bedienungsanleitung

Xerox

Xerox 6125N - Phaser Color Laser Printer Leitfaden

Xerox

Xerox Phaser 3121 Bedienungsanleitung

Xerox

Xerox Printer fwww Bedienungsanleitung

Xerox

Xerox PHASER 6140 Bedienungsanleitung

Xerox

Xerox 3130 - Phaser B/W Laser Printer Bedienungsanleitung

Xerox

Xerox Phaser 6360 Bedienungsanleitung

Xerox

Xerox Phaser 6120 Bedienungsanleitung

Xerox

Xerox 8080 Installations- und Betriebsanleitung

Xerox

Xerox 4213 Bedienungsanleitung

Xerox

Xerox PHASER 6250 Bedienungsanleitung

Xerox

Xerox DocuPrint N4525 Bedienungsanleitung

Xerox

Xerox WorkCentre 385 Bedienungsanleitung

Xerox

Xerox Tektronix Phaser 2135 Bedienungsanleitung

Xerox

Xerox 7700 Bedienungsanleitung

Xerox

Xerox Docutech 128 Technisches Handbuch

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung

Lexmark

Lexmark Infoprint 1332 Bedienungsanleitung