Xit XTDF18 Bedienungsanleitung
Item # XTDF18
INSTRUCTION MANUAL
Universal
High Power Auto-Focus
Digital SLR Flash
wide angle diffuser & reflection board
D-SLR
designed for
Warning
1. To avoid fire or electrical shock,do not expose this product to rain or moisture.
2. Do not flash at hight level output continuously for over 15 time.
3. To avoid short circuit,be sure the batteries contacts are securely packed and in
accordance with local provisinon when handling the batteries.
4. Please place the batteries and the parts which can be swallowed mistakenly away
from children. Contact a doctor immediately when it occurs.
5. To avoid possible injury to eyes, do not use the flash light on the people who need a
hight degree of attention.
6. Please take out the batteies and stop using immediately in case of below.
*This product is dropped or shocked seriously and the inner part of the product is bared.
*If this battery leaks corrosive liquieds, please take out the battery with golves.
*The product gives off strange smell, smokes or heats.
*Do not disassemble or maintain this product. Touching the internal high voltage circuit
will cause electric shock.
*Remove batteries during long periods of non-use.
-1-
Features
* Wireless triggering sensor: It can works in outdoor environment under S1
and S2 mode, the wireless triggering distance is up to 10-15M in outdoor,
20-30m in indoor.
* Super speed of charging recycle: It only takes 4 seconds in charging
* The improved power saving mode: In the power saving mode,the flash will
get automatic sleeping.
* The brightness of the fine control: The brightness is more refined, 8 levels
of output control(1/128-1/1), every level have six fine adjustment, cooperate
different zoom valule to get the flash effects what`s you demind for.
-2-
1
2
3
4
5
6
7 8
Nomenclature
1.Reflection board
2.Wide-angle diffuser
3.Flash head
4. Wireless sensor
5.Battery compartment cover
6.Hot shoe stand
7.Fixed dial
8.Contacts
9. Locking pin
-3-
M S1 S2
ZOOM
PILOT MODE ZOOM ON/OFF
9
10
11
12
13
14
15
16
17
18
24 28 35 50 70 85 mm
Nomenclature
-4-
Nomenclature
10. Mode indicator(M,S1 and S2): It indicateds the current flash mode.
11. Output level indicator: It can regulate the output power by setting the button, there are 8 levels
for output level adjustment. It indicates the output power and the fine-turning; it indicates the
coverage of the current focus length when adjusting the focus length
12. Test button
13. Mode switch button: The mode of the flash ligth will be switched among the M/S1/S2 in circle for
each press.
14. Charging indicator/Test button: The lighting of green light shows that charging process is finished
and flash can be used. the lighting of red light shows that it is in charging, the alternate flashing of
the green lights shows overheat protection. The red ligh blinking shows that shortage of power.
15. Power adjust button: The output power of the flash light can be adjusted through left button
16. Power switch: The power of the flash light can be opened or closed by hoding this button
for 2 Seconds.
17. Lamp holder electric zoom button
18. Power adjust button: The output power of the flash light can be adjusted through right button
19. ”SET”button: power adjust button
-5-
1
2
1
1
2
Installation Instruction
1. Install Batteries
Slide the batteries chamber’s cover in the direction of the arrow. Insert the
batteries according to the label inside battery chamber.Make sure the
direction of the batteries’ polarity is correct. Close the battery chamber cover
in the direction of the arrow.
-6-
a b c
2. Mount the speedlite on your camera
a. Loosen the locking ring by turning it in the direction of the arrow.
b. Slide the speedlite hot shoe stand into the camera hot shoe stand until it
stops. Turn the locking ring in the direction of the arrow tighten.
c. To detach the speedlite,loosen the locking ring by turning it in the oppo-
site direction.
-7-
Basic functions
1.Basic Operations
Operation of the buttons:
Component
<Power Switch>
<Mode Switch Button>
Power and focus adjustment
<LEFT>and <RIGHT> button
Power Switch of the flash light.The power of the flash light can be opened or
closed by holding this button for 2 seconds.It is suggested that the battery
shall be taken out after the power of the flash light is closed through this button.
The mode of the flash light will be switched among the M/S1/S2 in circle for each press.
The output power and focus of the flash light can be adjusted through these buttons
Power fine adjust <SET> button
<ZOOM> button
Please press Zoom Button into the fine adjust state , and cooperate left and right button
for adjust focus range, The head focus of the flash light will switch among the (24/28/35/
50/70/85/105) in circle for each press.
<Pilot Button> Press the test and the flash will test flashing in current output level
Press SET button into the fine adjust function
Operation
-8-
Meaning of(Output control indicator)
represents <ON> state of indicator’s light.
While O represents <OFF> state.
In M/S1/S2 Mode,indicates the output level
1/128
1/64
1/32
1/16
1/8
1/4
1/2
1/1
State of <Output level indicator> Output level
State
<Charging indicator>
Meaning
Operation
The red light is lit
The green light
is lit
The green lights
blink alternatively
The Flash ligth is
fully charged,and
can be used.
The Flash ligth has
not been fully
charged
The Flash ligth is
locked to prevent
overheating due
to frequent flashing.
Normal
If the red light is lit
for 20 seconds,
replace the batteries.
Wait indicator to be
green
-9-
The red lights
blink alternatively
Long time charged
shortage of power
supply
Charge time over
20S,please replace
batteries
Meaning of <Charging indicator>：
Inhaltsverzeichnis
