Xomax XM-R268 Bedienungsanleitung

Thank you for purchasing one of our XOMAX products! We appreciate your

Please read the following manual carefully before you install and use the unit.

Please save this manual in case you will need to clarify further possible ques-

tions regarding installation and usage of our product.

We are constantly trying to keep our online-library of user's manuals for our

products up-to-date. In case you miss some information or if something should

be unclear, please visit our homepage www.xomax.de for a current version of

user's manual or contact our customer service.

XM-R268

We appreciate our environment, so to keep it safe and clean, we

do not print our manuals on paper but provide our products with

manuals in digital version created in *.pdf format.

www.xomax.de, view them on your mobile devices and print them

for yourself if needed.

Please note: Any alternations and changes of technical data or/and design

due to technical update of some models need no advertisement.

User manual

XOMAX

Manual'sversion 1.0

Last update 0.0.201

Topic:

Safety instructions and precautions

Safety instructions and

precautions

Handling by stop only

To avoid any accidents please don't

handle the unit while you driving.

Please stop and park the vehicle

at safety place and handle the unit

casually.

Installation

Please read the following manual

carefully before you install the

unit. We recommend you to let the

technician install the unit in your

vehicle.

Regular loudness

Please set the loudness of the unit

to the appropriate level so you were

still able to hear exterior noises

especially trac warning signals.

Furthermore the higher loudness

level can damage your hearing

organs.

Repair of the unit

Do not open the unit. Do not try to

repair the unit by yourself due to

any emerging technical problems.

While opening the unit by yourself

exists the danger to be electrocuted.

Do not use the unit any further since

you detect any kind of technical

problems. Leave all the repair opera-

tions to professional technicians.

Due to awed warranty seal the

warranty becomes invalid.

Power supply

Use the unit connected only to 12 Volt

on-board power supply. The minus (-)

should be connected with the ground

(GND) (negative).

Due to the wrong grounding exists the

danger of re. In case of doubt please

consult with professional technicians.

Replacement of fuses

While replacing the fuse please make

sure that the new fuse has the same

properties as the old one, especially the

amperage.

Overheating

Do not occlude the vent holes to avoid

the heat generation and accumulation

in the unit. Otherwise exists the danger

of re.

Regular temperature

Please make sure that the temperature

inside the vehicle amounts to not more

than +60 C. If it's too hot inside the

vehicle, do not turn the unit on until

the inside temperature of the cabin

descends.

Topic: Safety instructions and precautions

Cleaning of the unit

Please keep the unit clean and remove

the dust from it regularly. Please use for

that a soft and dry cleaning rag.

Major soilings can be removed carefully

with the wet cleaning rag. Do not use

any chemical or alcohol-containing

detergents to avoid the damage of the

unit's varnish.

Moisture

electric shock do not put the unit in to

the moist environment (e.g. adverse

weather conditions, inappropriate wet

cleaning etc.)

Topic: Installation

Installation

Installation notes

notes and common information.

Before the installation

WARNING!

Please read the following manual care-

fully before you install the unit.

Damages caused due to an inapprop-

riate installation will not be covered by

warranty.

If you do not want to risk your warranty

entitlement, please let the technician

install the unit in your vehicle.

»To avoid a short circuit please

disconnect the vehicle battery before

the installation. To do it properly please

read the manual of your vehicle.

The detailed installation manual

xomax.de.

The printed version of a common

the package.

»Make sure that your vehicle is

equipped with a car radio slot of

required size (1DIN)

»As may be the case you will need a

suitable faceplate, adapter or other

accessories. These could be provided

from your local specialist supplier.

»The connection cables may not be

cutted or short-circuited. Otherwise the

warranty becomes invalid.

»Before the installation please make

sure that your vehicle has the 12 Volt

on-board power supply.

»The minus (-) should be connected

with the ground (GND) (negative).

»Please tag the polarity of the avai-

lable speakers before you disconnect

the vehicle battery.

»A proper grounding of the unit's

housing requires a clean ground

connection. Thus the grounding area

should be rust-, stain- and dust-free.

»Please ground the cable separately

from other heavy current devices such

»Please ensure that the colored cables

are connected according to the wiring

diagram. The wrong wiring may lead to

malfunctions or even damages of the

electric elements of the vehicle.

»Please note that the connection

cables of this unit and of the other

devices may have the same purpose but

connecting this unit with the

We recommend you to let the

technician install the unit in your

vehicle.

Topic:

Installation

»other devices please ensure that both

of the cables in each case have the

same purpose. To connect everything

correctly please refer to the manuals of

the both devices.

»Please ensure that the negative

speaker cable is in each case connected

with the negative speaker terminal of

the ISO port. Do not ever connect the

negative speaker cables with the vehicle

body.

»This unit is designed and construed

for connection with 4 speakers. Do not

combine this unit with devices that are

designed and construed for connection

with 2 speakers.

»The speakers should feature the

impedance of 4-8 Ohm and a sucient

wattage.

»Please ensure that the speakers you

are connecting with the unit are intact.

Damaged speakers can impair the unit.

»To avoid a short circuit please isolate

all cable junctions and endings of the

unused cables with the electrical tape.

»All the cables should be layed and

xated tidy and properly. The cables

should not contact any movable or hot

objects.

»If your vehicle doesn't have an "ACC"

ignition position, please connect the red

cable with the ignition switch. Other-

wise the unit will not turn o automati-

cally, causing the discharging of the

vehicle battery.

»To avoid a rogue and hazardous

short circuit do not lay the yellow cable

through the engine bay in order to

connect it with the vehicle battery.

»Do not ever connect speaker cables

among one another. In case you do not

want to connect all the 4 speakers with

the unit please isolate the endings of

unused cables with the electrical tape

to prevent a short circuit.

»Do not ever connect the negative

speaker cables with the vehicle body.

»To ensure a awless performance of

the unit the intergration angle should

amount to +/- 30.

Topic: Introduction

Operating elements

Topic:

Replacement instructions:

1. Remove the battery compartment:

push it to the left rst, then pull it out.

2. Remove the old battery and insert

the new one (CR-2025 Lithium).

3. Insert the battery compartment back

into the remote control till it clicks into

place.

Startup operations

Usage of the remote control

Before the rst usage please remove

the isolation plate.

Aim the remote control at the IR

receiver on the front operating panel.

The IR receiver should not be blocked.

As soon as the remote control does

not work proper the battery should be

replaced.

Do not expose the remote control to

direct sunlight or air heater.

Replacement of the battery

The remote control is operated by

CR-2025 Lithium battery.

As soon as the remote control does

not work proper the battery should be

replaced.

Topic:

Insert a micro SD card

Insert a micro SD card into the slot with

the label side up and the pin side down.

Make sure that the card is intact and

dirt-free.

Insert a USB flash drive

Insert an USB ash drive proper into a

USB plug.

Do not insert any heavy or big USB

ash drives in order not to hit it

accidently - it could cause damages of

the USB plug or USB ash drive.

Micro SD cards and USB ash

drives should have following le-

system format: FAT32. Other

types will not be supported.

Unit on/off

Press the ? button to turn the unit

on.

If the unit is already on, keep the ?

button pressed for a couple of seconds

to turn it down.

AUX input

The AUX input is a 3,5 mm jack plug on

the front operating panel.

Herewith you can connect the unit with

on of the external playback devices:

MP3 player, smartphone, cellphone or

tablet PC.

An adapter cable 3,5 mm jack-to-jack

will be required.

Press the MOD button (perhaps

several times) to get to AUX mode.

If the external device is connected with

the unit, the playback is audible via car

radio loudspeakers.

The playback control can be achieved

via external device only.

Following music formats are supported:

»» MP3 (with ID3 tags as well)

»» WMA

Thema:

WHITE.

The setting "AUTO" stands for the

automatic color change: the car radio

changes its illumination color every 3

seconds.

Bluetooth connection

Before the ﬁ rst usage of any Bluetooth

function the unit should be connected

via Bluetooth with the device of your

choice.

A Activate the Bluetooth function on

the external device (e.g. cellphone).

B Search for a new device named

"CAR BT" (this very unit).

C Select it to build a connection

between your cellphone and the unit.

D If required enter the password

"0000" and conﬁ rm the entry.

E Now the both are connected.

In order to ﬁ nd out how to activate the

Bluetooth function on your cellphone or

other device please read the correspon-

ding manual.

Once you have connected via

Bluetooth the unit with an external

device of your choice, the connec-

tion will be built automatically as

soon as the device appears in the

receiving area of the unit.

The Bluetooth function should be

"ON" both on the external device

and on the unit.

Please note that the left USB

slot is not suitable for charging the

mobile device battery. Please use

the right USB slot on the Fronta-

panel.

USB charging function

The right USB slot with charging func-

tion is located on the front panel. Insert

the USB charging cable from your

mobile device correctly and carefully

into the USB slot.

Please note that the right USB

slot is not suitable for playing the

media ﬁ les. No USB sticks are

accepted on this USB slot. Please

use the left USB slot for this.

Factory settings

Pressing the 9button (see page 6)

button you can set the unit back to the

factory settings.

Use a pencil or similar to press the

button. After reset the unit shuts down

automatically.

Set LED color

To change the illumination color, press

the knob until "AUTO" appears on the

screen.

Turn the knob to toggle between the

color settings: AUTO, BLUE, GREEN,

CYAN, RED, PURPLE, YELLOW and

Thema:

Hand-free phone call

This unit contains a Bluetooth feature

"hand-free phone call" which allows to

make your phone calls hand-free via

integrated microphone and loudspea-

kers.

Take a call

By incoming call press the BAND/T

button on the front panel to accept it.

Redial

Press the BAND/Tbutton to redial

the last number dialed.

End / reject a call

To end the active call or to reject the

incoming call press the MODE/U

button on the front panel.

Bluetooth music

The "Bluetooth music" feature allows to

play the music from the external device

of your choice (cellphone, smartphone,

tablet PC) via car radio speakers.

The device should support the A2DP

service.

Start Bluetooth music

Press the MODE/Ubutton several

times till the prompt "PHONE" o "BT

AUDIO" appears on the screen.

Now load the playback program on the

external device and start the playback.

Operate Bluetooth music

Following functions are available to

operate the playlist of the external

device via the unit:

CH+ Pause/resume playback

8Skip to previous track

7Skip to next track

A playlist has to be created via the

external device ﬁ rst.

Startup operations

Inhaltsverzeichnis

Andere Xomax Autoempfänger Handbücher

Xomax

Xomax XM-2RSU417 Bedienungsanleitung

Xomax

Xomax XM-2RSU419 Bedienungsanleitung

Xomax

Xomax XM-2CDB622 Bedienungsanleitung

Xomax

Xomax XM-RSU235BT Bedienungsanleitung

Xomax

Xomax XM-RD263 Bedienungsanleitung

Xomax

Xomax XM-VRSU311BT Bedienungsanleitung

Xomax

Xomax XM-RD264 Bedienungsanleitung

Xomax

Xomax XM-RSU259BT Bedienungsanleitung

Xomax

Xomax XM-RSU220 B/W Bedienungsanleitung

Xomax

Xomax XM-2R423 Bedienungsanleitung

Xomax

Xomax XM-VRSU4309BT v2 Bedienungsanleitung

Xomax

Xomax XM-RSU255BT Bedienungsanleitung

Xomax

Xomax XM-2VRSUA744 Bedienungsanleitung

Xomax

Xomax XM-RSU25 Series Bedienungsanleitung

Xomax

Xomax XM-RSU227BT Bedienungsanleitung

Xomax

Xomax XM-RSU216BT Bedienungsanleitung

Xomax

Xomax XM-2NVRS6201BT Bedienungsanleitung

Xomax

Xomax XM-DTSB931 Bedienungsanleitung

Xomax

Xomax XM-RSU221BT Bedienungsanleitung

Xomax

Xomax XM-RD276 Bedienungsanleitung

Xomax

Xomax XM-RSU256BT Bedienungsanleitung

Xomax

Xomax XM-CDB618 Bedienungsanleitung

Xomax

Xomax XM-CDB624 Bedienungsanleitung

Xomax

Xomax XM-CDB623 Bedienungsanleitung

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

JVC

JVC KD-AHD69 Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung