Xtralis VPS-215-E Installations- und Betriebshandbuch

Xtralis Power Supplies VPS-215-E & VPS-220-E Installation and Commissioning Instructions

www.xtralis.com Approved Document No. DFU0002150 Rev 3 www.xtralis.com Page 1 of 2

VPS-215-E & VPS-220-E are power supply units (PSU) for Xtralis Aspirating Smoke Detectors (ASD).

They are compliant with EN54-4:1997+A1:2002+A2:2006.

Xtralis VPS-215-E

(0.5A load, 7Ah max)

and

Xtralis VPS-220-E

(0.5A load, 14Ah max)

Location: Site the PSU indoors on a dry, flat surface in an area that is well ventilated. Where possible the panel’s indicators (internal and

external) should be at eye level and the unit should be installed in the same location as the ASD it powers.

Knockouts: Before mounting, remove selected knockouts with a sharp light tap, using a flat broadsided screwdriver (shown right). Fill knockout

holes with good quality cable glands.

Mounting: Mount the metal base securely onto a wall using the four mounting holes provided. Assess the condition and construction of the wall

and use No.8-10, or 4-5mm screws. Use the fixing hole template overleaf as a guide.

Wiring: Connect all AC cables BEFORE applying power. Maintain segregation between AC and DC cabling. All wiring should be installed in

accordance with relevant national standards, e.g. IEE Wiring Regulations BS7671 in the UK. Connect the incoming AC to CONN1 (②shown

overleaf)and ensure that earth straps are connected to the earth tag (shown right).

Connect DC: Connect the DC output to the Xtralis detector. Examples for the VESDA VLC, VLP and VLF are shown below which may use the General Purpose Input (GPI) to transmit the PSU

fault signal. The VESDA detector must be configured to interpret the GPI input as a ‘Mains OK’ if this feature is used.

Connect Batteries: Secure the batteries using battery straps and connect as shown. With charged batteries the DC output ⑧will turn on, the OK LED will illuminate and the Fault LED will also

illuminate (as there is no AC input).

CAUTION: Only use good quality sealed Valve Regulated Lead Acid (VRLA) batteries. There is a risk of explosion if the batteries are replaced by incorrect types.

Commissioning: Switch on the AC supply to the PSU. The OK LED should stay lit and the Fault LED should turn off.

Check the fault relay is energized (short circuit between C and NO terminals ⑪). Switch off the AC supply and confirm correct

operation of LEDs and relay –see table right. Restore the AC supply. Disconnect the batteries and confirm correct operation of

LEDs and relay –see table right.

Normal Operation/Fault Finding: The table in Step 7 provides a summary of the normal operation of the PSU when the battery and/or AC supply fails. When the AC supply fails, the DC output

is maintained for at least 24 hours as long as the batteries are in good condition. Damage to the batteries as a result of deep discharge is prevented by turning the DC output off (load shed mode)

when the battery voltage falls below approximately 21V. Should this happen the DC output will not be restored until the AC supply is re-established OR fully charged batteries have been installed.

However, the terminal voltage of the discharged batteries measured after the PSU has entered load shed mode may be greater than 21V because the voltage can recover when the battery is not

under load. Never leave the batteries connected for prolonged periods without an AC supply connected because, during load shed mode, there is a monitoring current Imin (<12mA) which, over

several days, will drain the batteries to the point they are damaged.

Batteries

LED

Fault

LED

Fault

relay

Fault terminals

OK (Healthy)

OFF

NO-C=short

OFF

NC-C=short

Not OK

(Discharged or

Disconnected

or Faulty)

OFF

NC-C=short

OFF

NC-C=short

Xtralis Power Supplies VPS-215-E & VPS-220-E Installation and Commissioning Instructions

www.xtralis.com Approved Document No. DFU0002150 Rev 3 www.xtralis.com Page 2 of 2

Legend

Description (UK)

Description (FR)

Beschreibung (DE)

Descriptiόn (ES)

Descrizione (IT)

Value

①

AC supply

230Vac, 50/60Hz (tested +10% / -15%)

②

AC supply input terminals

L=LIVE, N=Neutral, =Earth

③

PSU earth strap: connect to enclosure

earth tag

PSU is CLASS 1 AND MUST BE EARTHED

④

AC supply fuse (F1): high rupturing

capacity, ceramic

1A HRC, 20mm

⑤

Red LED: Hazardous voltages in PCB

hashed area

Hazardous voltages =

⑥

PLK1 Charge current link. Remove if

using batteries <7Ah (Minimum 2Ah)

PLK2 Battery monitoring link. Fit if

batteries NOT used

⑦

Power output (maximum and battery cut

off voltage)

24Vdc (V max = 30V, V min = 19.5V)

I max a & I max b with PLK1 fitted

0.5A

I max a & I max b with PLK1 NOT fitted

1A (non EN54-4 certified)

Output ripple voltage (peak-to-peak)

1.2V@30MHz bandwidth, 600mV 100nF loading

⑧

Battery connection to VRLA batteries

Maximum internal battery resistance

Ri max = 1500mΩ

I min: Monitoring current in load shed

<12mA

AC supply/battery charger monitored



Batteries monitored



Charging is temperature compensated



VPS-215-E battery size (Yuasa NP type

or equivalent)

2 x 12V, 7Ah (NP7-12)

VPS-220-E battery size (Yuasa NP type

or equivalent)

2 x 12V, 7Ah (NP7-12) or

2 x 12V, 12Ah (NP12-12) or

4 x 12V, 7Ah (NP7-12)

⑨

VPS-215-E indications: Internal only.

Output OK (Green LED), Fault(Yellow LED)

Output OK = Fault =

VPS-220-E indications: External only.

Output OK (Green LED), Fault(Yellow LED)

Output OK = Fault =

⑩

PL1: 4-way display connector

⑪

Fault relay: isolated relay output

Change-over NO-COM-NC 1A@50V

⑫

PL2: high temperature output (unused)

Operates at approx 55oC internal box temp, 30V

200mA max current sink.

⑬

Battery fuse (F2): fast, glass

3.15A F, 20mm

⑭

Charge Off Input: Disablement of battery

charger when closed (unused)

⑮

Wiring loom to Display PCB (VPS-220-E

only)

VPS-215-E dimensions (H x W x D)

VPS-215-E weight (without batteries)

286 x 226 x 113mm

2.5kg

VPS-220-E dimensions (H x W x D)

VPS-220-E weight (without batteries)

351 x 255 x 110mm

3kg

VPS-215-E mounting

4 x Ø5mm holes on 220 x 180mm centres

VPS-220-E mounting

4 x Ø5mm holes on 270 x 180mm centres

Temperature range

Maximum relative humidity (RH)

Ingress protection (IP) Rating

-5oC to +40oC ambient

95% RH

IP30

Dieses Handbuch passt für folgende Modelle

Andere Xtralis Stromversorgung Handbücher

Xtralis

Xtralis VESDA VPS-VEA-115UL Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung