Xtralis VESDA-E VEP-1P Kurzanleitung

DUCTS APPLICATION NOTE

February 2021

Doc. No. 35424_02

Ducts Application Note VESDA-E

35424_02 i

Preface

Xtralis has designed an air sampling smoke detection system specifically for use in ventilation ducts. The

information contained in this document will assist you when designing VESDA-E systems for this type of

application.

Note!

This system is not suitable for use in flexible ducts.

Related Products

VESDA-E VEP-1P and VEA detectors have been specially adapted for installation in ducts. Their model

numbers are VEP-A00-1P, VEA-040-A00 and VEA-040-A10.

Ducts Application Note VESDA-E

35424_02 ii

Contents

1VESDA-E System Design......................................................................................................................1

Sampling Pipe Configuration in Small Ducts...........................................................................1

1.1.1 VESDA-E VEP-1P ...........................................................................................................1

1.1.2 VESDA-E VEA.................................................................................................................2

Sampling Pipe Configuration in Large Ducts...........................................................................3

1.2.1 VESDA-E VEP-1P ...........................................................................................................3

Key Design Considerations .......................................................................................................5

1.3.1 VESDA-E VEP-1P ...........................................................................................................5

1.3.2 VESDA-E VEA.................................................................................................................5

2VESDA-E System Installation...............................................................................................................6

Environmental Conditions .........................................................................................................6

2.1.1 VESDA-E VEP-1P ...........................................................................................................6

2.1.2 VESDA-E VEA.................................................................................................................7

Key Installation Considerations ................................................................................................7

3VESDA-E System Commissioning.......................................................................................................8

Hole Orientation Adjustment .....................................................................................................8

3.1.1 VESDA-E VEP-1P ...........................................................................................................8

System Performance Verification............................................................................................10

4System Maintenance...........................................................................................................................11

Local Codes & Standards.........................................................................................................11

First Year Requirements...........................................................................................................11

On-Board Filter Replacement ..................................................................................................11

Site Visit Requirements............................................................................................................11

Disclaimer On The Provision Of General System Design Recommendations........................................12

Ducts Application Note VESDA-E

35424_02 1

1 VESDA-E System Design

Sampling Pipe Configuration in Small Ducts

1.1.1 VESDA-E VEP-1P

Small ducts are defined as those of width less than 1 m (3.28 ft). The figure below (Figure 1) shows a side

view of a duct section with the insertion positions for the VESDA-E VEP-1P detector inlet and exhaust pipes.

The detector inlet pipe should be installed in the middle of the duct at height H, where H is half of the duct

diameter. The detector exhaust pipe should be inserted approximately 0.5 m (1.64 ft) downstream of the inlet

pipe, at a quarter of the height of the duct.

Figure 1: Side view of the inlet and exhaust pipe

positions for a small ventilation duct.

A top view of the above installation is shown below (Figure 2). The number of inlet pipe sampling holes, their

required size and spacing are listed in Table 1. Both sampling pipe and exhaust pipe holes have the same

orientation with respect to the direction of the duct airflow.

Figure 2: Top view of the inlet and exhaust

pipe positions, including sampling hole location, for a small duct.

The sampling hole sizes, for the inlet pipe, are shown in Table 1. The exhaust pipe must have 4 × Ø10 mm

(13/32 inch) holes, regardless of the width of the duct. These holes should be located in the middle of the duct

width at least 50 mm (2 inches) from the side walls.

Ducts Application Note VESDA-E

35424_02 2

Table 1: Sampling hole requirements for a VESDA-E VEP-1P detector with 5 m (16.4 ft.)

inlet pipe and 2 m (6.56 ft.) exhaust pipe in small ducts.

Duct width (m) {ft}

Number of Holes

Hole Ø (mm) {in}

Nominal Pipe Flow

Rate (L/min) {cfm}

0.3 {1.0}

{15/64}

40.8 {1.43}

0.5 {1.7}

{13/64}

44.2 {1.56}

0.7 {2.3}

{5/32}

38.6 {1.36}

0.9 {3.0}

{5/32}

46.4 {1.64}

Note!

Nominal sampling hole spacing is 0.2 m (0.66 ft.).

1.1.2 VESDA-E VEA

Return air sampling is achieved with microbore tubes for VEA system inserted in the return air duct behind the

exhaust grill. it is recommended the tubes are installed facing perpendicular to the duct airflow (Figure 3). A

specific sampling point, VSP-980-ST (No. 35295), must be used for VEA’s duct sampling. It can be mounted

on the duct by VEA Sampling Point Duct Bracket, part number VSP-1008.

Figure 3: Side view of the inlet tube position for a small ventilation duct

The detector inlet tube should be installed in the middle of the duct at height H, where H is half of the duct

diameter.

Ducts Application Note VESDA-E

35424_02 3

Figure 4: Top view of the inlet tubes positions, including duct mounting

bracket for a small ventilation duct.

These sampling points should be located in the middle of the duct width at least 50 mm (2 inches) from the

side walls.

Note!

Nominal sampling point spacing is 0.2 m (0.66 ft.).

Sampling Pipe Configuration in Large Ducts

1.2.1 VESDA-E VEP-1P

Large ducts are defined as those with widths of 1 to 2 m (3.28 to 6.56 ft). For these ventilation ducts, it is

recommended that the inlet pipe of the smoke detector be in two branches. The figure below (Figure 5) shows

a side view of a duct section with the relative insertion points for the inlet and exhaust pipes. The two inlet

branches are located at a quarter of the height (H) of the duct with the exhaust pipe inserted mid-height

approximately 0.5 m (1.64 ft) downstream of the inlet pipes.

Figure 5: Side view of the inlet and exhaust

pipe positions for a large duct.

The following figure (Figure 6) shows a cross-section view of the same duct with the positions of the inlet

branches and exhaust pipe indicated. The number of inlet pipe sampling holes, recommended hole size and

spacing are presented in Table 2.

Ducts Application Note VESDA-E

35424_02 4

Figure 6: Cross-section view of the inlet pipe

sampling hole setup and exhaust pipe in large ducts.

Table 2: Sampling hole requirements for a VESDA-E VEP-1P detector with 5 m (16.4 ft) inlet pipes

and 2 m (6.56 ft) exhaust pipe in a large duct.

Duct width (m) {ft}

Number of Holes

Hole Ø (mm) {in}

Nominal Pipe Flow

Rate (L/min) {cfm}

1.0 {3.3}

3.5

{9/64}

45.8 {1.62}

1.5 {5.0}

3.0

{1/8}

47.8 {1.69}

2.0 {6.5}

3.0

{1/8}

57.0 {2.01}

Note!

Nominal sampling hole spacing is 0.4 m (1.3 ft).

The exhaust pipe must have 4 × Ø10 mm (13/32 inch) sampling holes, regardless of the width of the duct.

These holes should be located in the middle of the duct width at least 50 mm (2 inches) from the side walls.

Note!

Calculations, performed with the ASPIRE pipe design software tool and

shown in Tables 1 and 2, apply to a 5 m (16.4 ft) inlet pipe and a 2 m (6.56 ft)

exhaust pipe. These calculations are suitable for an inlet pipe length of 1 to 10

m (3.28 to 32.8 ft) and an exhaust pipe length of < 2 m (6.56 ft), provided that

corresponding pipe flow rate adjustments are made. Always refer to local

codes and standards for hole size and spacing requirements.

Ducts Application Note VESDA-E

35424_02 5

Key Design Considerations

1.3.1 VESDA-E VEP-1P

The following should be considered when designing a VESDA-E VEP-1P for duct protection:

•All inlet and exhaust pipes must be sealed at their far end with an end-cap.

•The holes on the inlet and exhaust pipes should be facing the airflow as shown in the above figures.

Holes with the same orientation eliminate unwanted flow faults associated with cyclical operation,

maintenance or power failure of the duct system. However, in some industrial applications, where the

quality of air inside the duct is poor, it is recommended that all holes on the inlet and exhaust pipes face

downstream, that is, 180° to the incoming airflow).

•The pipes should always be held in position at the duct walls with fittings such as rubber grommets.

Silicon is recommended, to ensure an airtight seal.

•Regardless of duct width, the exhaust pipe must have 4 × Ø10 mm (13/32 inches) holes.

•Never simultaneously sample from multiple ducts or ambient environments with the same the detector.

1.3.2 VESDA-E VEA

The following should be considered when designing a VESDA-E VEA for duct protection:

•Sampling points install in duct pressures within -30Pa to +30Pa.

•Maximum differential pressure (DP) of 30Pa between sampling points on same VEA unit.

•The exhaust of the VEA unit must be within a pressure range -30Pa to +30Pa.

Ducts Application Note VESDA-E

35424_02 6

2 VESDA-E System Installation

Environmental Conditions

2.1.1 VESDA-E VEP-1P

You will need equipment to measure the following environmental conditions when installing a VESDA-E system

in a duct:

•Temperature.

•Humidity.

•Static Pressure – the pressure generated by the fan to deliver a specific flow-rate in the duct. This

pressure is a function of the flow-rate and impedance of the duct system.

•Air Pressure.

•In air-return ducts, the smoke detector must be installed where the static pressure is above −500 Pa

and the air velocity in the duct is below 20 m/s or, converted to volumetric flow rate (m3/hr) = velocity

× duct area.

•Always vent the exhaust pipe back into the ventilation duct, even when the duct pressure is sometimes

< 20 Pa, because the duct system operation may change in the future.

Condensation may occur when the dew point temperature of the air in the ventilation duct is at or above the

ambient temperature of the area where the smoke detector is installed. This usually occurs when the

temperature of the humid air in the duct is higher than the ambient temperature of the air outside the duct,

where the detector is to be installed, and the temperature of the air inside the sampling pipes of the detector.

You should measure the temperature and humidity both inside the duct and in the area where the detector will

be installed. If the results indicate that condensation may be a problem, refer to the ‘Duct Sampling and

Condensation’ section of the Pipe Network Installation Manual for advice on how to modify the design. The

Pipe Network Installation Manual (Document Number 10255) forms part of the VESDA-E System Design

Manual.

One solution for combating condensation is to mount the detector on its side (Figure 7). This places the laser

chamber higher than the aspirator so that any water in the inlet pipe does not reach the detector chamber.

Figure 7: VESDA-E VEP-1P detector sideways mounting

solution, to combat condensation.

The sampling pipe should be removed from the detector regularly for inspection, especially during winter, to

determine whether any condensation is forming inside the pipes.

Smoke tests should be conducted regularly during the first two months following installation. If the smoke tests

fail, condensation may have affected the air filter in the detector. Replace the air filter and re-test. The

condensation problem will need to be addressed by following the methods described above.

Ducts Application Note VESDA-E

35424_02 7

If you have any doubts about the installation, seek support from your local Xtralis office or VESDA distributor.

2.1.2 VESDA-E VEA

Ensure duct environmental conditions do not lead to water condensation inside the tube.

Key Installation Considerations

You must consider the following when installing a VESDA-E system for duct protection:

•For air-return (negative pressure) ducts, smoke sampling must occur:

- Upstream and away from any fans.

- Upstream of humidifiers, heating coils and filters.

- Upstream of fresh air intakes.

•For a smoke detector mounted on the duct, ensure there are no tangible vibrations when the duct

system is in full operation. If there are vibrations, insert visco-elastic foam between the smoke detector’s

mounting bracket and the external surface of the duct.

•The inlet pipe/tube of the VESDA-E detector must be inserted at a distance of six to ten duct widths or

diameters from any flow disturbance caused by sharp bends, plenums, nozzles, branch connections

etc. Hence this system is not suitable for flexible ducts.

•Make sure that sampling holes/points are at least 50 mm (2 inches) away from the duct walls.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Xtralis Rauchmelder Handbücher

Xtralis

Xtralis vesda LaserFOCUS VLF-500 Bedienungsanleitung

Xtralis

Xtralis VESDA VLS Bedienungsanleitung

Xtralis

Xtralis VESDA-E VEU-A00 Bedienungsanleitung

Xtralis

Xtralis ICAM ILS-2 Bedienungsanleitung

Xtralis

Xtralis VESDA VLP Bedienungsanleitung

Xtralis

Xtralis XAS-2-US Bedienungsanleitung

Xtralis

Xtralis ICAM IFT Bedienungsanleitung

Xtralis

Xtralis VESDA VLI Montageanleitung

Xtralis

Xtralis VESDA Bedienungsanleitung

Xtralis

Xtralis VESDA VLC-605 Bedienungsanleitung

Xtralis

Xtralis vesda LaserFOCUS VLF-500 Bedienungsanleitung

Xtralis

Xtralis ICAM IAS-1 Bedienungsanleitung

Xtralis

Xtralis VESDA VLC-400 Bedienungsanleitung

Xtralis

Xtralis VESDA-E VES-A10-P Bedienungsanleitung

Xtralis

Xtralis VESDA VLS Bedienungsanleitung

Xtralis

Xtralis VESDA-E VEP-A10-P Bedienungsanleitung

Xtralis

Xtralis VESDA-E VEU Service-Handbuch

Xtralis

Xtralis VESDA VFT-15 Bedienungsanleitung

Xtralis

Xtralis OSID Montageanleitung

Xtralis

Xtralis XAS-1-US Bedienungsanleitung

Xtralis

Xtralis Xtralis ICAM ILS-1 Bedienungsanleitung

Xtralis

Xtralis VESDA VLC Bedienungsanleitung

Xtralis

Xtralis VESDA VFT-15-C Bedienungsanleitung

Xtralis

Xtralis ICAM IFT-P Bedienungsanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

BRK electronic

BRK electronic First Alert P1010 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Safetec

Safetec SDS-2/6 Betriebsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Ei Electronics

Ei Electronics Ei Ei168RC Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung