Yaesu FTM-3100R Installationsanleitung
Quick Manual
1 VOL knob
2 LCD display
3 DIAL knob
4 Power/LOCK key
5 V/M MW key ( )
6 MHz SETUP key ( )
7 TXPO key (
TXPO
)
8 REV DW key ( )
9 SQL key (
SQL
)
10 External MIC jack
Adjusting the volume
Rotate the volume clockwise/counterclockwise to adjust
the volume level.
Tuning in to the frequency
Press to switch to VFO mode, then rotate the DIAL.
Press to make the first three digits of the frequency
display blink, then rotate the DIAL to set the frequency
by one MHz increments.
Changing the transmit power level
Press
TXPO
, then rotate DIAL to select the transmit pow-
er level.
“HIGH” à“LOW” à“MID”
Press
TXPO
to set the transmit power level.
Restoring defaults (All Reset)
All transceiver settings and memory content may be
restored to the default settings.
Turn the power OFF.
While pressing
TXPO
, , and , turn the power
ON.
When “ALL RESET PUSH V/M KEY” appears, release
the keys.
Press to reset.
Locking the keys and DIAL
Press Power/LOCK to lock the keys and knobs.
Press Power/LOCK again to unlock.
Returning to the operating screen
Press and hold for over one second to return to the
operating screen from the Setup menu.
Supplements • Press to return to the previous
screen.
• Press and hold for over one sec-
ond to return to the operating screen.
FTM-3100R
EH052N560
VOL
DIAL
DW MW
SETUP
REV V/MMHz
SQL TXPO
10 9 8
3
5 47 6
2
1
Communicating
Transmitting
While pressing [PTT]on the microphone, speak into the mi-
crophone keeping it approximately 5 cm from your mouth.
The upper and lower portions of the indicator light are
red.
Receiving
Release
[PTT]
on the microphone to return to receive
mode.
Scanning
The FTM-3100DR is equipped with a scanning function
to search for memory channels and frequencies with
active signals.
VFO scan
Press to switch to VFO mode.
Press and hold
[
UP
]
or
[
DWN
]
on the microphone for
over one second.
Pressing
[
UP
]
scans in the higher frequency direction.
Pressing
[
DWN
]
scans in the lower frequency direction.
Press
[
UP
]
,
[
DWN
]
or
[PTT]
on the microphone to cancel
scanning (this does not put the transceiver into transmit
mode).
Memory scan
Frequencies registered to the memory channels can be
scanned in the memory channel number order.
Press to switch to memory mode.
Press and hold
[
UP
]
or
[
DWN
]
on the microphone for
over one second.
Pressing
[
UP
]
scans the memory channels in an upward
direction.
Pressing
[
DWN
]
scans the memory channels in a down-
ward direction.
Press
[
UP
]
,
[
DWN
]
or
[
PTT
]
on the microphone to cancel
scanning (this does not put the transceiver into transmit
mode).
Using the memory channels
Frequently used frequencies can be registered to the
memory channels. You can also assign a name to each
memory channel.
Registering frequencies
Switch to VFO mode, then rotate the DIAL to tune in
to the frequency you want to register to the memory
channel. Press and hold for over one second, then
rotate the DIAL to select the desired memory channel
and press .
Assigning a name to the memory channel
Press to switch to memory mode. Rotate the DIAL
to select the memory channel that is to be assigned a
name. Press and hold for over one second, then
rotate the DIAL to select “MEM NAME 18”.
Press , then rotate the DIAL to input the name.
You can move the cursor to the right by pressing .
Press and hold for over one second to save the
input name.
Andere Handbücher für FTM-3100R
3
Andere Yaesu Auto-Videosystem Handbücher
