Yaesu SCU-17 Bedienungsanleitung

SCU-17 USB InterfaCe UnIt 3

SCU-17 USB INTERFACE UNIT

Instruction Manual

日本語の説明は 16 ページから記載されています。

SCU-17 USB InterfaCe UnIt4

SCU-17 USB InterfaCe UnIt 1

Introduction

The SCU-17 interface unit may be used for CAT control of the transceiver with

a computer via a USB connection; and for communications using SSTV, RTTY

and PSK digital modes.

Note: YAESU does not produce CAT, SSTV, RTTY and PSK System operating

software, due to the wide variety of personal computers, operating sys-

tems, and applications in use today.

The SCU-17 provides CAT communication through the USB terminal when a

PC does not have an RS-232C connection.

The SCU-17 is equipped with a USB audio system device, so the TX and RX

audio system signals are accessible to the SCU-17 through the USB cable.

Therefore, the supplied USB cable is the only connection needed between

the SCU-17 and PC.

The SCU-17 is equipped with a two-channel USB serial device and enables

the various transmission modes and the CAT communication simultaneously.

The SCU-17 operates from the USB bus power; you do not need to prepare

an external power supply.

For RF isolation, the SCU-17 is designed with photo relays for the PTT/FSK

terminals. AF transformers are used in the AUDIO IN/OUT lines to provide

excellent ground isolation.

The SCU-17 is equipped with the TX and RX audio controls on the front pan-

el, for convenient level adjustment.

LED indicators on the SCU-17 front panel monitor the PTT and FSK control.

The operating conditions may be quickly conrmed.

Introduction

SCU-17 USB InterfaCe UnIt2

Virtual COM port driver Installation

Install the virtual COM port driver on the personal computer before using the

SCU-17 USB interface unit.

Please see the USB Driver (Virtual COM Port Driver) on the Yaesu Website for

details (http://www.yaesu.com/).

Note: Do not connect the USB cable and SCU-17 to your personal computer

until after the “virtual COM port driver” installation is completed, because

an incorrect driver may be installed.

 For assistance with the software port conguration, refer to “How to Conrm

the Installation, and the COM Port Number” in the “Virtual COM port Driver

Installation Manual”.

 For information on port conguration for commercial and free computer soft-

ware, refer to the manual for the software being used.

When using the USB cable to supply TX and RX audio signals, set the

Sound Card (input and output) settings to “USB Audio CODEC”.

When using the USB cable for computer TX control, the transceiver may

switch to transmit mode when the computer is started, etc.

YAESU does not provide technical support for the use or operation of com-

mercial or free computer software.

SCU-17 USB InterfaCe UnIt 3

Accessories

USB cable (Type “A” male to Type “B” male) ................................................. 1 pc

RS-232C cable (female to female, Straight Type) .......................................... 1 pc

Connection cable (MDIN6P - MDIN6P).......................................................... 1 pc

3.5 mm Stereo plug .................................................................................. 2 pcs

Instruction manual

①②③④⑤

⑥ ⑦ ⑧ ⑨

① N/A ⑥ N/A

② SERIAL IN ⑦ RTS

③ SERIAL OUT ⑧ CTS

④ N/A ⑨ NC

⑤ GND

① DATA OUT ④ FSK OUT

② GND ⑤ DATA IN

③ DATA PTT ⑥ SQL IN

FSK

PTT/FSK AUDIO

PTTGND

①②

③④

⑤⑥

OUT

INGND

SCU-17 USB InterfaCe UnIt4

Controls & Connections

①RX audio level control knob

This knob adjusts the RX audio level.

②TX audio level control knob

This knob adjusts the TX audio level.

③FSK Indicator

This indicator illuminates when the Mark frequency is shifted.

④TX Indicator

This indicator illuminates during transmission.

⑤POWER Indicator

⑥USB Connector

Connect to a computer from this jack using the supplied USB cable.

⑦CAT/RS-232C Jack

This 9-pin serial DB-9 jack allows CAT communication of the transceiver.

Connect a supplied RS-232C cable here and to the transceiver.

⑧3.5 mm stereo Jack (PTT/FSK)

This 3-conductor, 3.5 mm stereo jack is used for PTT/FSK. For RF isolation, these terminals

are designed with photo relays.

⑨DATA Jack

This 6-pin (MDIN6P) jack allows DATA communication of the transceiver.

⑩3.5 mm stereo Jack (Audio IN/OUT)

This 3-conductor, 3.5 mm stereo jack is used for Audio IN/OUT. For RF isolation, AF transform-

ers are used in the AUDIO IN/OUT lines.

This Jack is equipped with an attenuator that is applied to the audio output.

See page 13 for details about attenuation.

① ② ③ ④ ⑤

⑥ ⑦ ⑧ ⑨ ⑩

Front Panel

Rear Panel

SCU-17 USB InterfaCe UnIt 5

FTDX1200

FT-450D

System Setup

Supplied USB Cable

USB port

Supplied Connection Cable

DATA

Supplied RS-232C Cable

FTDX1200

FT-450D

CAT

SCU-17 USB InterfaCe UnIt6

System Setup

FT-950

Supplied USB Cable

USB port

Supplied Connection Cable

DATA

Supplied RS-232C Cable

CAT

FT-950

SCU-17 USB InterfaCe UnIt 7

System Setup

FT-2000 Series

DATA IN (Green) DATA PTT (Orange)

DATA PTT (Orange)DATA OUT (Brown)

DATA IN (Green) SQL IN (Blue)

GND (Red)

FSK OUT (Yellow)

USB port

FT-2000 Series

CAT

Supplied USB CablePacket Interface Cable "CT-39A" (option)

Supplied RS-232C Cable

SCU-17 USB InterfaCe UnIt8

FTDX9000 Series (SSTV/PSK/RTTY)

DATA PTT (Orange) GND (Red)

N.CDATA OUT (Brown)

DATA IN (Green) SQL IN (Blue)

FSK OUT (Yellow)

GND (Red)

DATA IN (Green)

USB port

CAT

Supplied USB Cable

Packet Interface Cable "CT-39A" (option)

Supplied RS-232C Cable

FTDX9000 Series

System Setup

Andere Handbücher für SCU-17

Inhaltsverzeichnis

Andere Yaesu USB-Schnittstelle Handbücher

Yaesu

Yaesu SCU-17 Bedienungsanleitung

Beliebte USB-Schnittstelle Handbücher anderer Marken

PASCO

PASCO SCIENCEWORKSHOP 750 Bedienungsanleitung

Phonic

Phonic FIREFLY 302 USB Bedienungsanleitung

OHAUS

OHAUS Scout STX Series Bedienungsanleitung

Denon

Denon DN-HC4500 - DJ Mixer USB Controller Bedienungsanleitung

Lutron Electronics

Lutron Electronics Stanza SZ-CI-USB-CPN5138 Bedienungsanleitung

Paradox

Paradox PMC5-TI00 Bedienungsanleitung

System Sensor

System Sensor M200WC-RF Leitfaden

Philips

Philips PDIUSBD12 Bedienungsanleitung

KNX

KNX Module IC-USB-S.1 Bedienungsanleitung

Velleman

Velleman KSR10/USB Bedienungsanleitung

NIEUWKOOP

NIEUWKOOP RG7100 Installationsanleitung

Alldaq

Alldaq ADQ-USB 2.0-ISO Bedienungsanleitung

Thorsis Technologies

Thorsis Technologies isDNet USB Bedienungsanleitung

Thorsis Technologies

Thorsis Technologies isHRT USB Bedienungsanleitung

microHAM

microHAM DigiKeyer Bedienungsanleitung

Apogee

Apogee Jam X Bedienungsanleitung

RigExpert

RigExpert TI-3000 Bedienungsanleitung

microHAM

microHAM USB Interface II Bedienungsanleitung