Yamaha DX7 MiniMAX Handbuch

DX7 MiniMAX Page 1 of 6 Install v2.10

www.musictechnologiesgroup.com Preliminary

Yamaha DX7 MiniMAX Expansion Install

1: Introduction

The DX7 MiniMAX a simple option board that provides increased memory and control of the DX7.

While the installation is fairly simple, it still requires patience and general electronics

knowledge. We accept no responsibility for the work you perform on your DX7. Read over

the following installation description and if you feel you are not capable of the work

required, turn the project over to a qualified technician

Precautions!

High Voltage Safety Warning

Unplug the audio cable. Turn the DX7 power switch OFF and unplug it from the wall.

Disconnect any other connected cables before opening the DX7.

ESD Precautions and Proper Handling Procedures

You should observe standard static-safe handling behavior when working with sensitive electronic

equipment such as synthesizers:

o Avoid carpets in cool, dry areas.

o Dissipate static electricity before handling any system components by touching a

grounded metal object.

o If possible, use anti-static devices, such as wrist straps and floor mats.

o Take care when installing the board. Prevent damage to the connectors by aligning

connector pins before you apply pressure. A damaged pin can render the board unusable

and can cause damage to system components at power-on.

o If disconnecting a cable, always pull on the cable connector, not on the cable itself.

Tools Required

o Standard Philips screwdriver.

o Standard flat-head screwdriver (small).

Condition of DX7

While the DX7 MiniMAX will replace the functionality of damaged or missing EPROM and/or

SRAM chips, it will not correct other problems your vintage synthesizer may have. It is

recommended that the synth be in otherwise good condition before beginning the installation. For

instance, the battery voltage should be checked and the battery replaced/repaired by a tech if

necessary. Sockets for the EPROM and SRAM chips should be in good working order and not be

DX7 MiniMAX Page 2 of 6 Install v2.10

www.musictechnologiesgroup.com Preliminary

dirty, oxidized, rusted or otherwise compromised. If repair is required, do it before installing the

DX7 MiniMAX.

2: Installation





Back up your patches if they are important to you!

Open the DX7

Using a Philips head screwdriver, remove the 5 screws from the front panel. Two are located

on the left front. Two are located on the right front. A final one is located on the right rear. Set the

screws aside, noting that the rear panel one is the shortest.

(Re)Move the Keybed & Remove the Keyboard Rail

It can be difficult to see the delicate pins when installing the DX7 MiniMAX board. By moving the

keybed (the chassis with the keys) and removing the silver keyboard rail, you will have better

sight lines and freedom of movement when installing the DX7 MiniMAX board.

Remove the 4 large external screws from the underside of the keyboard along the front

edge. The photo below shows the inside front edge of the empty case bottom and illustrates the

location of the 4 screws. You will, of course, be unscrewing from the DX7 underside.

Loosen the 3 internal screws at the extreme right and left ends that hold the keybed in

place. It is not necessary to extract them from the holes they reside in.

DX7 MiniMAX Page 3 of 6 Install v2.10

www.musictechnologiesgroup.com Preliminary

Carefully lift the keybed slightly up and out (toward yourself) an inch or so.. You don't need

to move it much. You will probably need to free up one or more cables to accomplish it. Or if you

prefer, disconnect the cables and completely remove the keybed.

This will give you access to the 3 screws holding the silver keyboard rail in place. Remove those

three screws and set aside the silver keyboard rail. (Shown here with keybed removed).

You now have excellent

access to the DX7 main

board. If you do remove the

keybed you may find it easier

to remove the small yellow

cable and large flat grayish

cable at the main-board-end

rather than from the keybed.

You will also need to unclip

two small cables on the left

end (mod wheel and pitch

bend). There may also be

wire tires and/or cable

fasteners to deal with.

Remove the EPROM and SRAM ICs

The next step is to remove the EPROM and two SRAM ICs.

The EPROM is found in location IC14 and the two M5M5118P SRAM chips (or similar) are

located at IC21 and IC20.

Remove them by prying slowly at each end of the chip back-and-forth with a small flat-head

screwdriver. Avoid touching any of the metal pins with the screwdriver.

DX7 MiniMAX Page 4 of 6 Install v2.10

www.musictechnologiesgroup.com Preliminary

Place them safely aside on anti-static foam. You can use the reverse side of the foam shipped

with the DX7 MiniMAX.

The photo above shows the 3 chips removed.

After removing the chips, also remove the screw shown at the

center of these photos near IC23.

Install the DX7 MiniMAX Printed Circuit Board

Hand tighten the supplied nylon standoff into the screw position near IC23. Tighten it well by

hand, but there is generally no need to use a tool. Do not over tighten or strip the threads.

Remove the DX7 MiniMAX board from the anti-static foam. Inspect the bottom of the board to

make sure none of the pins have been damaged. You should see one collection of 28 pins (2

parallel strips of 14 pins), one strip of 12 pins and a strip of 8 pins.

DX7 MiniMAX Page 5 of 6 Install v2.10

www.musictechnologiesgroup.com Preliminary

Place the DX7 MiniMAX board gently on the DX7 main board so that the 28 pins that form a DIP

package align with the vacated IC14 spot. The 8 pins along the edge should align with IC20 and

the other 12 pins should align with IC21. Do not press the board in place yet. You can use a

small mirror to check the pin alignment.

Once you are happy that all the pins are aligning with the desired locations, firmly and evenly

press the DX7 MiniMAX board in place. Make a visual check to see that the board is flush with

the sockets.

Using a screwdriver, carefully tighten the original main board screw through the DX7 MiniMAX

board into the nylon standoff. Again do not force it or over tighten as this can not only strip

the standoff, but it can cause the DX7MiniMAX board to change position. It should be tight

enough so that it cannot work lose. Double check the pins.

Reassembly

Remove all tools from the DX7. Carefully reassemble the DX7 in the reverse order, taking care to

replace the correct screws in the various locations. If you disconnected the green keybed ground

strap wire don't forget to screw it back in.

DX7 MiniMAX Page 6 of 6 Install v2.10

www.musictechnologiesgroup.com Preliminary

Test

Plug the AC cable in and turn it on. After a few moments, you should get a greeting message like:

* Welcome to *

* MiniMAX v2.1 *

Initialization

Since technically the battery has been removed, you may find some of the standard DX7 function

settings have been scrambled. Follow the steps below to put the DX7 into a known good state

before loading your patches back in.

Function settings on number 8 have been enhanced and new functions 12 and 13 have been

added.

1. Press MEMORY PROTECT / INTERNAL then OFF.

Internal memory protect is now off.

2. Press FUNCTION and then button 12. Use the Data Slider to set the FUNCTION CONTROL

Memory Bank to 1 (there are only 4 RAM banks, numbered 1 to 4, regardless of what the

initial LCD value says).

3. Press button 13 and set the FUNCTION CONTROL MIDI OUT= channel to your preferred

value from 1 to 16 (usually 1).

4. Press button 8 repeatedly until you see FUNCTION CONTROL MIDI IN= and set this

channel to your preferred value (1 to 16 or All which is OMNI mode).

Check/set the standard DX7 Function settings versus your preferences. You should be able to

load some patches now, but it is still possible that some setting prevents the sound from being

heard.

The patch data memory will certainly be garbled. Use the standard DX7 panel operations to load

the current data bank with your patches. The “Yamaha DX7 MiniMAX User Guide” will explain

how to select memory banks as well as how to use the other features of this expansion.

Enjoy your updated DX7!

See the MTG web site for more great vintage synth and drum machine goodies.

Inhaltsverzeichnis

Andere Yamaha Computerhardware Handbücher

Yamaha

Yamaha EMP100 Bedienungsanleitung

Yamaha

Yamaha FX500 Bedienungsanleitung

Yamaha

Yamaha GQ1031 Bedienungsanleitung

Yamaha

Yamaha EMP100 Bedienungsanleitung

Yamaha

Yamaha MY8-SDI-ED Bedienungsanleitung

Yamaha

Yamaha PLG100-DX Bedienungsanleitung

Yamaha

Yamaha DME Series Benutzerhandbuch

Yamaha

Yamaha MY8-AEB Bedienungsanleitung

Yamaha

Yamaha ME2000 Bedienungsanleitung

Yamaha

Yamaha MMP1 Bedienungsanleitung

Yamaha

Yamaha DMP9-16 Bedienungsanleitung

Yamaha

Yamaha S90 Bedienungsanleitung

Yamaha

Yamaha PLG100-VL Bedienungsanleitung

Yamaha

Yamaha PLG150-DX Kurzanleitung

Yamaha

Yamaha DP100 Bedienungsanleitung

Yamaha

Yamaha PLG100-VL Bedienungsanleitung

Yamaha

Yamaha MEP4 Bedienungsanleitung

Yamaha

Yamaha MEP4 Bedienungsanleitung

Yamaha

Yamaha DX7 8X EXP Bedienungsanleitung

Yamaha

Yamaha PLG100-XG Bedienungsanleitung

Yamaha

Yamaha EMP100 Handbuch

Yamaha

Yamaha DSP-1 Bedienungsanleitung

Yamaha

Yamaha MY8-SDI-ED Bedienungsanleitung

Yamaha

Yamaha PLG150-VL Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung