Yamaha MCP1 Bedienungsanleitung

EnglishDeutschFrançaisEspañolPortuguêsItalianoРусский

日本語

WALL-MOUNT CONTROLLER

MCP1

施工説明書

Installation Manual

Installationshandbuch

Manuel d’installation

Manual de instalación

Manual de instalação

Manuale all’installazione

Руководство по установке

2 MCP1 Installation Manual

(can_b_02)

(class bkorea)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

CAN ICES-3 (B)/NMB-3(B)

이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로 하며, 모든 지역에

서 사용할 수 있습니다.

1. IMPORTANT NOTICE: DO NOT MODIFY

THIS UNIT!

This product, when installed as indicated in

the instructions contained in this manual,

meets FCC requirements. Modifications not

expressly approved by Yamaha may void your

authority, granted by the FCC, to use the prod-

uct.

2. IMPORTANT: When connecting this product

to accessories and/or another product use

only high quality shielded cables. Cable/s sup-

plied with this product MUST be used. Follow

all installation instructions. Failure to follow

instructions could void your FCC authorization

to use this product in the USA.

3. NOTE: This product has been tested and

found to comply with the requirements listed in

FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements

provides a reasonable level of assurance that

your use of this product in a residential envi-

ronment will not result in harmful interference

with other electronic devices. This equipment

generates/uses radio frequencies and, if not

installed and used according to the instruc-

tions found in the users manual, may cause

interference harmful to the operation of other

electronic devices. Compliance with FCC reg-

ulations does not guarantee that interference

will not occur in all installations. If this product

is found to be the source of interference, which

can be determined by turning the unit “OFF”

and “ON”, please try to eliminate the problem

by using one of the following measures:

Relocate either this product or the device that

is being affected by the interference.

Utilize power outlets that are on different

branch (circuit breaker or fuse) circuits or

install AC line filter/s.

In the case of radio or TV interference, relo-

cate/reorient the antenna. If the antenna lead-

in is 300 ohm ribbon lead, change the lead-in

to co-axial type cable.

If these corrective measures do not produce

satisfactory results, please contact the local

retailer authorized to distribute this type of

product. If youcan not locate the appropriate

retailer, please contact Yamaha Corporation of

America, Electronic Service Division, 6600

Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those

products distributed by Yamaha Corporation of

America or its subsidiaries.

(class B)

FCC INFORMATION (U.S.A.)

3MCP1 Installation Manual

PRECAUTIONS

PLEASE READ CAREFULLY

BEFORE PROCEEDING

Please keep this manual in a safe

place for future reference.

WARNING

Always follow the basic precautions

listed below to avoid the possibility of

serious injury or even death from

electrical shock, short-circuiting,

damages, fire or other hazards. These

precautions include, but are not limited

to, the following:

Do not open

• This device contains no user-serviceable

parts. Do not open the device or attempt to

disassemble the internal parts or modify

them in any way. If it should appear to be

malfunctioning, discontinue use

immediately and have it inspected by

qualified Yamaha service personnel.

Water warning

• Do not expose the device to rain, use it

near water or in damp or wet conditions, or

place on it any containers (such as vases,

bottles or glasses) containing liquids which

might spill into any openings. If any liquid

such as water seeps into the device, turn

off the power of the PoE injector or the PoE

network switch immediately and unplug

the cable. Then have the device inspected

by qualified Yamaha service personnel.

• Never insert or remove a cable with wet

hands.

Fire warning

• Do not place any burning items or open

flames near the device, since they may

cause a fire.

If you notice any abnormality

• If any of the following problems occur,

immediately turn off the PoE injector or the

PoE network switch and disconnect the

cable.

- Unusual smells or smoke are emitted.

- Some object has been dropped into the

device.

- Cracks or other visible damage appear

on the device.

Then have the device inspected or

repaired by qualified Yamaha service

personnel.

CAUTION

Always follow the basic precautions

listed below to avoid the possibility of

physical injury to you or others, or

damage to the device or other property.

These precautions include, but are not

limited to, the following:

Location

• Do not place the device in a location where

it may come into contact with corrosive

gases or salt air. Doing so may result in

malfunction.

• Always consult qualified Yamaha service

personnel if the device installation requires

construction work, and make sure to

observe the following precautions.

- Choose mounting hardware and an

installation location that can support the

weight of the device.

- Avoid locations that are exposed to

constant vibration.

- Use the required tools to install the

device.

- Inspect the device periodically.

PA_en_8 1/2

4 MCP1 Installation Manual

Handling caution

• Avoid inserting or dropping foreign objects

(paper, plastic, metal, etc.) into any gaps

or openings on the device (panel, etc.). If

this happens, immediately turn off the

power of the PoE injector or the PoE

network switch, unplug the cable, and

have the device inspected by qualified

Yamaha service personnel.

• Do not rest your weight on the device or

place heavy objects on it. Avoid applying

excessive force to the buttons, switches or

connectors to prevent injuries.

NOTICE

To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to

other property, followthe notices below.

Handling and maintenance

• Do not use the device in the vicinity of a TV, radio, AV equipment, mobile phone, or other electric

devices. Otherwise, the device, TV, or radio may generate noise.

• Do not expose the device to excessive dust or vibration, or extreme cold or heat (such as in

direct sunlight, near a heater, or in a car during the day), in order to prevent the possibility of

panel disfiguration, unstable operation, or damage to the internal components.

• Do not place vinyl, plastic or rubber objects on the device, since this might discolor the panel.

•When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning

fluids, or chemical-impregnated wiping cloths.

• Condensation can occur in the device due to rapid, drastic changes in ambient tempera-

ture—when the device is moved from one location to another, or air conditioning is turned on or

off, for example. Using the device while condensation is present can cause damage. If there is

reason to believe that condensation might have occurred, leave the device for several hours

without turning on the power until the condensation has completely dried out.

•Besure to operate the switch with bare hands. The switch will not work properly if operated with

gloved hands.

Information

About functions/data bundled with the device

• Use STP (Shielded Twisted Pair) cable to prevent electromagnetic interference.

Regarding disposal

• This product contains recyclable components. When disposing of this product, please contact

the appropriate local authorities.

About this manual

• The illustrations and screens as shown in this manual are for instructional purposes only.

• The company names and product names in this manual are the trademarks or registered trade-

marks of their respective companies.

•Software may be revised and updated without prior notice.

Yamaha cannot be held responsible for

damage caused by improper use or

modifications to the device.

PA_en_8 2/2

5MCP1 Installation Manual

Contents

PRECAUTIONS .....................................................................3

Introduction .......................................................................6

Controls and Connectors ........................................................7

Front Panel................................................................................................. 7

Rear Panel.................................................................................................. 8

Connections with an MTX/MRX system .......................................9

Function tree.................................................................... 10

Installation ...................................................................... 11

Setting the UNIT ID ............................................................. 13

Removal.......................................................................... 14

Initializing the MCP1 .......................................................... 14

Alert list.......................................................................... 15

Specifications .................................................................. 17

Dimensions ...................................................................... 18

Included items

•Mounting plate

•Surface mount box

• Side panel × 2

•Mainunit — mounting plate screws × 4 (with washers)

•Mounting plate — surface mount box screws × 4 (without washers)

• MCP1 installation manual (this document)

Firmware update

MTX-MRX Editor is used to update the firmware of the MCP1 and to check the version.

For details on howto perform these operations, refer to “MTX-MRX Editor User Guide.”

The latest firmware can be downloaded from the download page of the following website.

http://www.yamahaproaudio.com/

6 MCP1 Installation Manual

Introduction

Thank you for purchasing the Yamaha MCP1 wall-mount controller. This product is a

wall-mount controller for controlling the MTX/MRX system. This installation manual

explains how to mount the unit when the installing technician or the designer installs or

sets-up the system. In order to take full advantage of this product’s many functions, be

sure to read this installation manual before installation.

After reading this manual, keep it for future reference.

The MCP1 lets you set up a home page and six pages, and assign up to 36 parameters.

What you’ll need to provide

When attaching the MCP1 to a wall, you’ll need to provide several items.

• PoE injector or PoE network switch that supports IEEE802.3af

This is used between the MTX/MRX system and the MCP1 in order to supply power to the

MCP1.

PoE injector units and PoE network switches are collectively referred to as “PSE (Power

Sourcing Equipment).”

• Ethernet cables (CAT5e or better)

These are used between the MTX/MRX and the PSE, and between the PSE and the MCP1.

• (If embedding the unit in the wall)

2-gang box (without separator; 20 mm or greater depth)

Yo u’ll also need screws for attaching the gang box to the wall.

• (If using a surface mount box)

Screws for attaching the surface mount box to the wall × 4

Provide M4.0 flat head screws of a length appropriate for the thickness of the wall.

• Phillips screwdriver / electric screwdriver

This is used for installation.

7MCP1 Installation Manual

Controls and Connectors

Front Panel

qHome switch

Touch this to return to the home page.

If youlong-touch (more than two seconds) when the home page or another page is dis-

played, you’ll move to the utility page. If youlong-press this while the display is locked or

sleeping, the lock or sleep state is defeated.

wL1/2/3 and R1/2/3 switches

Use these switches to move from the home page to another page, or to operate parameters.

Use MTX-MRX Editor to specify the pages or parameters.

eDisplay

This shows parameters and other information. Use MTX-MRX Editor to create the data that

will be shown.

rReturn switch

After setting a parameter, touch this switch to confirm and return to the page or to move to a

confirmation screen.

Controls and Connectors

8 MCP1 Installation Manual

Rear Panel

tNETWORK port

This is an RJ-45 port for connection to the Dante port or [NETWORK] port of the MTX/MRX

via the PSE.

The maximum cable length that can be used is 100 meters.

NOTE

Use STP (Shielded Twisted Pair) cable to prevent electromagnetic interference.

9MCP1 Installation Manual

Connections with an MTX/MRX system

Up to 16 MCP1 units can be connected to an MTX/MRX system.

Use an Ethernet cable to connect the MTX/MRX’s [NETWORK] port or Dante port to a PoE

network switch, and use an Ethernet cable to connect the PoE network switch to the MCP1.

If the network switch does not support PoE, connect a PoE injector between the network

switch and the MCP1.

In some cases, the PSE (PoE network switch or PoE injector) might have ports that supply

power and ports that do not supply power. Connect the MCP1 to a port that supplies power.

For details on howto synchronize each device, refer to “MTX-MRX Editor User Guide.”

Connections for a small system

Connections for a large system

Computer

MTX3

SWR2100P-5G

MCP1

Maximum 100 meters

Computer

MRX7-D

SWR2100P-10G

MCP1

Maximum

100 meters

XMV8280-D

SWP1-16MMF

MCP1 MCP1 MCP1

10 MCP1 Installation Manual

Function tree

If youlong-touch (more than two seconds) the home switch when the home page or another

page is displayed, you’ll move to the utility page. The utility page contains the following func-

tion tree.

• LCD Brightness

Adjusts the brightness of the display backlight. Higher numbers increase the brightness.

• LCD Contrast

Adjusts the contrast of the display. Higher numbers increase the contrast.

• LED Brightness

Adjusts the brightness of the switches. Higher numbers increase the brightness.

•Settings

Moves to the settings page.

After synchronizing with MTX-MRX Editor, it will be necessary to enter the PIN code.

• IP Setting

Selects either PC or UNIT ID as the method of specifying the MCP1’s IP address.

In the case of PC, use MTX-MRX Editor to specify the IP address.

In the case of UNIT ID, the IP address will be 192.168.0.UNIT ID.

After selecting PC or UNIT ID, touch the return switch to move to the confirmation

screen and automatically restart.

•UnitID

Specifies the MCP1’s UNIT ID. The range of this setting is 01 through FE.

If IP Setting is UNIT ID, make settings so that there is no conflict with the IP address of

another device.

After specifying UNIT ID, touch the return switch to move to the confirmation screen and

automatically restart.

• Initialize

Initializes the MCP1.

• Version

Display the firmware version of MCP1.

•Alert

Display the alert number which has occurred current.

LCD Brightness

LCD Contrast

LED Brightness

Settings

IP Setting

Unit ID

Initialize

Version

Alert

Utility page

Inhaltsverzeichnis

Andere Yamaha Controller Handbücher

Yamaha

Yamaha RCX340 Bedienungsanleitung

Yamaha

Yamaha MJC8 Bedienungsanleitung

Yamaha

Yamaha Nexo NXAMP4X4 Bedienungsanleitung

Yamaha

Yamaha RCX141 Bedienungsanleitung

Yamaha

Yamaha MJC8 Bedienungsanleitung

Yamaha

Yamaha RCX142 Bedienungsanleitung

Yamaha

Yamaha MLC-200 Bedienungsanleitung

Yamaha

Yamaha RCX222 Bedienungsanleitung

Yamaha

Yamaha G10 Bedienungsanleitung

Yamaha

Yamaha SRCD Series Betriebsanleitung

Yamaha

Yamaha Mark IV Bedienungsanleitung

Yamaha

Yamaha SRCP Bedienungsanleitung

Yamaha

Yamaha TS-P Bedienungsanleitung

Yamaha

Yamaha RCX340 Bedienungs- und Montageanleitung

Yamaha

Yamaha CEmarking RCX221 Bedienungsanleitung

Yamaha

Yamaha AFC1 Bedienungsanleitung

Yamaha

Yamaha TS-S Bedienungsanleitung

Yamaha

Yamaha SRCP30 Bedienungsanleitung

Yamaha

Yamaha C20A Bedienungsanleitung

Yamaha

Yamaha RCX40 Bedienungsanleitung

Yamaha

Yamaha RCX240 Bedienungsanleitung

Yamaha

Yamaha ENSPIRE Controller Bedienungsanleitung

Yamaha

Yamaha disklavier DKC-850 Stücklistenhandbuch

Yamaha

Yamaha DRCX Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch