Yamaha MX360 Handbuch
MX360
SUPPLEMENTARY
SERVICE MANUAL
7HC-F8197-11LIT-19616-02-34
2015_09×1 !
7HC-F8197-11_cover-mihiraki.indd 1 2015/09/01 9:52:50
B
L
B
B/W
Y
R
R
B
B/W
B/W
Y
B
1
2
3
4
5
6
1 Sparkplug
2 TCIunit
3 Oilwarningunit
4 Oillevelswitch
5 Oilwarninglight
6 Engineswitch
Color code
B Black
L Blue
R Red
Y Yellow
B/W Black/White
CIRCUIT DIAGRAM
7HC-F8197-11_cover-mihiraki.indd 2 2015/09/01 9:52:50
FOREWORD
This Supplementary Service Manual has been
prepared to introduce new service and new
data for MX360.
For complete information on service proce-
dures, it is necessary to use this Supplementary
Service Manual together with following manual:
This manual was written by the Yamaha Motor
Powered Products Co., Ltd. primarily for use
by Yamaha dealers and their qualified mechan-
ics. It is not possible to put an entire mechan-
ic’s education into one manual, so it is
assumed that persons using this book to per-
form maintenance and repairs on Yamaha
Multi-Purpose Engine have a basic under-
standing of the mechanical precepts and pro-
cedures inherent to Multi-Purpose Engine
repair technology. Without such knowledge,
attempted repairs or service to this model may
render it unfit for use and/or unsafe.
Yamaha Motor Powered Products Co., Ltd. is
continually striving to further improve all mod-
els manufactured by Yamaha. Modifications
and significant changes in specifications or
procedures will be forwarded to all Authorized
Yamaha dealers and will, where applicable,
appear in future editions of this manual.
HOW TO USE THIS MANUAL
PARTICULARLY IMPORTANT
INFORMATION
Particularly important information is distin-
guished in this manual by the following nota-
tions.
This is the safety alert symbol. It is used to
alert you to potential personal injury haz-
ards. Obey all safety messages that follow
this symbol to avoid possible injury or
death.
WARNING
A WARNING indicates a hazardous situa-
tion which, if not avoided, could result in
death or serious injury.
NOTICE
A NOTICE indicates special precautions
that must be taken to avoid damage to the
machine or other property.
TIP
A TIP provides key information to make proce-
dures easier or clearer.
MX360
SUPPLEMENTARY SERVICE MANUAL
©2015 by Yamaha Motor
Corporation, U.S.A.
1st Edition, September 2015
All rights reserved. Any reprinting or
unauthorized use without the written
permission of Yamaha Motor
Corporation, U.S.A.
is expressly prohibited.
LIT-19616-02-34
MX360
SERVICE MANUAL:
7HC-F8197-10. LIT-19616-02-32
7HC-F8197-11.indb 1 2015/09/01 14:08:17
HOW TO USE THIS MANUAL
This manual is intended as a handy, easy-to-read reference book for the mechanic.
Comprehensive explanations of all installation, removal, disassembly, assembly, repair and check
procedures are laid out with the individual steps in sequential order.
9 The manual is divided into chapters and each chapter is divided into sections. The current sec-
tion title is shown at the top of each page 1.
9 Sub-section titles appear in smaller print than the section title 2.
9 To help identify parts and clarify procedure steps, there are exploded diagrams at the start of
each removal and disassembly section 3.
9 Numbers are given in the order of the jobs in the exploded diagram. A number indicates a dis-
assembly step 4.
9 Symbols indicate parts to be lubricated or replaced 5.
Refer to “ILLUSTRATED SYMBOLS”.
9 A job instruction chart accompanies the exploded diagram, providing the order of jobs, names of
parts, notes in jobs, etc. 6. This step explains removal procedure only. For installation, reverse
the steps.
9 Jobs requiring more information (such as special tools and technical data) are described
sequentially 7.
3-20
ENG
CYLINDER HEAD COVER, CYLINDER HEAD
6543
2
78
9
78
11 Nm (1.1 m · kgf, 8.0 ft · lbf)
20 Nm (2.0 m · kgf, 14 ft · lbf)
2.3 Nm (0.23 m · kgf, 1.7 ft · lbf)
12 Nm (1.2 m · kgf, 8.7 ft · lbf)
50 Nm (5.0 m · kgf, 36 ft · lbf)
1st
2nd
7 Nm (0.7 m · kgf, 5.1 ft · lbf)
9
1
Order Job/Parts to remove Q’ty Remarks
Removing the cylinder head cover,
cylinder head
Remove the parts in the order listed.
Fuel tank Refer to “FUEL TANK, CANISTER” on 3-4.
Muffler Refer to “MUFFLER” on 3-6.
Air filter Refer to “AIR FILTER” on 3-3.
Carburetor Refer to “CARBURETOR” on 4-1.
Flywheel cover Refer to “FLYWHEEL” on 3-12.
1 Spark plug cap 1
2 Spark plug 1
3 Air filter case stay 1
4 Cylinder head cover 1
5 Cylinder head cover gasket 1
6 Cylinder air shroud 1
7 Locknut 2
8 Adjuster 2
9 Screw 2
CYLINDER HEAD COVER, CYLINDER HEAD
chap03.indd 20 2015/09/01 13:14:45
3-22
ENG
CYLINDER HEAD COVER, CYLINDER HEAD
CHECKING THE PUSH ROD
1. Check:
9 Pushrodrunout
Runout limit:
Refer to “SPECIFICATIONS” in
the Supplementary service
manual.
Outofspecifications→Replace.
CHECKING THE CYLINDER HEAD
1. Check:
9 Cylinderheadcombustionchamber
Checkthecombustionchamberforcar-
bondeposits.
Anycarbondeposits→Eliminate.
TIP
Besurenottodamagethecontactsurfaceof
thecylinder.
2. Check:
9 Cylinderhead
Cracks/damage around the hole of
sparkplug→Replace.
CHECKING THE ROCKER ARM
1. Check:
9 Rockerarm
Wear/damage/cracks→Replace.
chap03.indd 22 2015/09/01 13:15:18
1
4
3
6
7
2
5
7HC-F8197-11.indb 2 2015/09/01 14:08:17
ILLUSTRATED SYMBOLS
(Refer to the illustration)
SYMBOL DEFINITION SYMBOL DEFINITION
General information Periodic checks and
adjustments
Engine Carburetor
Electrical Troubleshooting
Specifications Filling fluid
Lubricant Special tool
T
R
.
.
Tightening torque Wear limit, clearance
Engine speed Electrical data
Replace the part with a new one. LS Lithium-soap base grease
MMolybdenum disulfide grease
E
Engine oil
M
Molybdenum disulfide oil LT Apply locking agent (LOCTITE®)
7HC-F8197-11.indb 3 2015/09/01 14:08:18
7HC-F8197-11.indb 4 2015/09/01 14:08:18
INDEX
GENERAL INFORMATION GEN
INFO
ENGINE ENG
ELECTRICAL
ELEC
SPECIFICATIONS SPEC
1
2
3
4
7HC-F8197-11.indb 5 2015/09/01 14:08:19
CHAPTER 1.
GENERAL INFORMATION
MACHINE IDENTIFICATION .....................1-1
ENGINE SERIAL NUMBER ..................1-1
STARTING SERIAL NUMBER ..............1-1
DIMENSIONS .............................................1-2
DIMENSION CHART ............................1-2
TOP .......................................................1-3
LEFT SIDE ............................................1-3
FRONT ..................................................1-4
MOUNTING BASE ................................1-4
CHAPTER 2.
ENGINE
GOVERNOR ...............................................2-1
ADJUSTING THE GOVERNOR ............2-2
CHAPTER 3.
ELECTRICAL
CIRCUIT DIAGRAM ...................................3-1
CHAPTER 4.
SPECIFICATIONS
GENERAL SPECIFICATIONS ...................4-1
MAINTENANCE SPECIFICATIONS ..........4-3
ENGINE ................................................4-3
ELECTRICAL ........................................4-7
TIGHTENING TORQUES ...........................4-8
GENERAL TORQUE
SPECIFICATIONS ....................................4-10
LUBRICATION POINTS AND TYPE
OF LUBRICANTS ....................................4-11
WIRE ROUTING DIAGRAM ....................4-12
UPPER SIDE VIEW ............................4-12
ENGINE SWITCH AND OIL
WARNING UNIT .................................4-13
TCI UNIT .............................................4-14
OIL LEVEL SWITCH
(CRANKCASE COVER) .....................4-15
7HC-F8197-11.indb 6 2015/09/01 14:08:19
1-1
GEN
INFO
MACHINE IDENTIFICATION
1
1
2
GENERAL INFORMATION
MACHINE IDENTIFICATION
ENGINE SERIAL NUMBER
The serial number is printed on the label 1
affixed to the position 2 of the multi-purpose
engine as shown in the illustration.
TIP
The first four digits identify the model, and
the remaining digits indicates the production
number.
STARTING SERIAL NUMBER
MX360AA6A6: 7HCJ-3000101–
TIP
Designs and specifications are subject to
change without notice.
7HC-F8197-11.indb 1 2015/09/01 14:08:19
1-2
GEN
INFO
DIMENSIONS
DIMENSIONS
DIMENSION CHART
Unit: mm
Model (Code) PTO shaft dimensions (Type) Mounting face dimensions
MX360 AA6A6
(7HCJ)
4.5
5
72.2
28
60.3
88.5
25.4 -0.021
0
110 +0.054
0
146.08 -0.040
0
21.8 -0.1
0
6.31 +0.058
0
3/8 -24UNF-2B
30
30
146.08
0
-0.040
165.1
127
110 +0.054
0
4 3/8-16UNC2B DEPTH18
4 5/16-24UNF-2B DEPTH18
45
45
2 5/16-24UNF-2B DEPTH18
*1: UNF; Unified fine thread (Unit: in)
*2: UNC; Unified coarse thread (Unit: in)
7HC-F8197-11.indb 2 2015/09/01 14:08:19
Andere Handbücher für MX360
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Yamaha Motorrad Handbücher
Yamaha
Yamaha Tmax XP500Z Bedienungsanleitung
Yamaha
Yamaha V-star XVS65X Bedienungsanleitung
Yamaha
Yamaha YZF-R1 2003 Handbuch
Yamaha
Yamaha TW200 Bedienungsanleitung
Yamaha
Yamaha XVS950CR Bedienungsanleitung
Yamaha
Yamaha XJ6NA Bedienungsanleitung
Yamaha
Yamaha PW80(R) Anwendungshandbuch
Yamaha
Yamaha XT250X Bedienungsanleitung
Yamaha
Yamaha FZ6Y Bedienungsanleitung
Yamaha
Yamaha XJ1100J Bedienungsanleitung
Yamaha
Yamaha 2005 Virago XV250T Bedienungsanleitung
Yamaha
Yamaha SRX600 1997 Bedienungsanleitung
Yamaha
Yamaha XTZ 125K Bedienungsanleitung
Yamaha
Yamaha YFM45KDXK Bedienungsanleitung
Yamaha
Yamaha Thunderace YZF1000R Bedienungsanleitung
Yamaha
Yamaha MT09SPMC Bedienungsanleitung
Yamaha
Yamaha YXF10WRAN Bedienungsanleitung
Yamaha
Yamaha star XVS13CE Bedienungsanleitung
Yamaha
Yamaha TT-R110E(Z) Bedienungsanleitung
Yamaha
Yamaha 1986 XV1000 Bedienungsanleitung
Beliebte Motorrad Handbücher anderer Marken
APRILIA
APRILIA ETV MILLE CAPONORD - PART1 02-2001 Bedienungsanleitung
KTM
KTM Freeride E-XC 2021 Bedienungsanleitung
Fantic
Fantic Enduro 125 Bedienungsanleitung
Ducati
Ducati Supersport 750 desmodue Bedienungsanleitung
MV Agusta
MV Agusta 2008 F4 312RR 1078 Gebrauchsanweisung
Ducati
Ducati 748 monoposto strada Bedienungsanleitung
ATK
ATK 1988 250 Bedienungsanleitung
Excelsior-HENDERSON
Excelsior-HENDERSON 1999 HCX Bedienungsanleitung
Triumph
Triumph Thunderbird Bedienungsanleitung
Ducati
Ducati 996 Bedienungsanleitung
BMW
BMW MOTORRAD K 1200 R Sport Installations- und Wartungshandbuch
BMW Motorrad
BMW Motorrad G 650 GS 2007 Installations- und Wartungshandbuch