Yamaha CBX-D5 Bedienungsanleitung

CBX-D5

DIGITAL RECORDING PROCESSOR

Owner's Manual 1

SYSTEM SETUP GUIDE

Introduction 1Introduction 1Chapter 1 : Introduction 1

1 Introduction

This guide explains how to setup a number of CBX-D5 based recording systems.

Table of contents

Introduction – page 1

Cubase Audio & Atari ST/STE System – page 2

Cubase Audio & Atari TT System – page 4

Digital Performer & Apple Macintosh System – page 6

Future updates

From time to time this guide will be updated using single sheet supplements. Please see

your Yamaha dealer for the latest supplement.

Trademarks

Appleand Macintoshare registered trademarks of Apple Computer, Inc.

Atari, ST, TT, and STEare registered trademarks of Atari Corporation.

Mark of the Unicornis a registered trademark of Mark of the Unicorn, Inc.

All other trademarks are the property of their respective holders.

NOTE: Although the system setups shown in the manual are valid at the time of

printing, there is a possibility that future software upgrades may require

different setups. Therefore, please refer to the manual of the controlling

software, for the latest setup requirements.

2 Chapter 2 : Cubase Audio & Atari ST/STE System2 Chapter 2 : Cubase Audio & Atari ST/STE System2 Chapter 2 : Cubase Audio & Atari ST/STE System

2 Cubase Audio & Atari ST/STE System

An overview

In this system the CBX-D5 is used with an Atari ST/STE computer and the supporting

software is Cubase Audio by Steinberg.

What you will need

1) The CBX-D5, a power cable, two MIDI cables, a 50-way SCSI cable, and a SCSI

terminator (all these except for one MIDI cable are provided with the CBX-D5).

2) An Atari ST computer and an Atari video monitor.

3) Steinberg’s Cubase Audio software (Atari version).

4) A SCSI hard disk and a 25-pin D-SUB to 50-way SCSI cable.

5) A Steinberg DMA to SCSI Converter II, its power supply, and a 19-pin D-SUB to

19-pin D-SUB cable.

Making the connections

1) Connect the Atari computer’s “MIDI OUT” connector to the CBX-D5’s “MIDI IN”

connector, and the computer’s “MIDI IN” connector to the CBX-D5’s “MIDI OUT”

connector using the MIDI cables.

2) Connect the Atari computer’s “HARD DISK” connector to the SCSI adaptor’s

“DMA IN” connector using the 19-pin D-SUB to 19-pin D-SUB cable.

3) Connect the SCSI adaptor’s “SCSI” connector to one of the hard disk’s SCSI

connectors using the 25-pin D-SUB to 50-way SCSI cable.

4) Connect the other hard disk SCSI connector to one of the CBX-D5’s SCSI

connectors using the 50-way SCSI cable.

5) Insert the CBX-D5’s SCSI terminator into the CBX-D5’s unused SCSI connector.

6) Connect the CBX-D5 to an AC receptacle using the supplied power cable.

7) Connect the Atari computer and its video monitor to an AC receptacle.

8) Connect the SCSI adaptor’s power supply (refer to its Operating Manual for details).

Settings

1) Set the CBX-D5 to SCSI ID “5 or 6” using the thumb wheel switch on the rear of the

CBX-D5.

2) Set the CBX-D5’s “TO HOST” switch to “MIDI”.

3) Set the hard disk to SCSI ID “0” (refer to its Operating Manual for details).

4) Set the SCSI adaptor as speciﬁed in its Operating Manual.

NOTE: Clinch the SCSI connector’s spring retaining clips and tighten the 25-pin

D-SUB connector’s locking screws for secure connections.

NOTE: 1. Hard disks must be set with continuous SCSI IDs starting from 0

(0, 1, 2, 3…).

2. Do not set the ID number of the CBX-D5 so that it is consecutive to

the ID number of the “HARD DISK”.

Switching on the power 3Switching on the power 3Switching on the power 3

Figure 1. System connections

Switching on the power

1) Switch on the SCSI devices: CBX-D5, hard disk, SCSI adaptor.

2) Switch on the Atari computer and load Cubase Audio.

What to do next

• The SCSI hard disk must be formatted before it can be used (refer to the hard disk’s

Operating Manual). See also “Working with Hard Disks” on page 18 of the CBX-D5

Operating Manual.

• For recording and playback you should refer to the Cubase Audio Operating

Manuals. See also “Recording” on page 20 and “Playback” on page 23 of the

CBX-D5 Operating Manual.

Notes:

• Other MIDI devices can be connected in this system as shown in “MIDI” on page 30

of the CBX-D5 Operating Manual.

• For audio device connection, see “Inputs & Outputs Explained” on page 26 of the

CBX-D5 Operating Manual.

• For more details about SCSI hard disks and connecting extra disks, see “Connecting

Hard Disk Drives” on page 13 of the CBX-D5 Operating Manual.

• In this system, only one external hard disk is used. It is, however, highly

recommended, for the sake of data integrity, that you use at least two hard disks: one

disk for your computer software and data such as Cubase Audio, MIDI song ﬁles,

etc., and the other disk purely for recording CBX-D5 sound ﬁles.

ATARI

ST/STE

DMA IN

CBX-D5

HARD

DISK

MIDI IN

MIDI OUT

DMA to SCSI

Converter @

HARD DISK

50-WAY to 25-PIN

SCSI CABLE

SCSI

TERMINATOR

50-WAY SCSI

CABLE

POWER

CABLE

POWER

SUPPLY

19-PIN to 19-PIN

D-SUB CABLE POWER

CABLE

POWER

CABLE

MIDI OUT

MIDI IN

MIDI CABLES

4 Chapter 3 : Cubase Audio & Atari TT System4 Chapter 3 : Cubase Audio & Atari TT System4 Chapter 3 : Cubase Audio & Atari TT System

3 Cubase Audio & Atari TT System

An overview

In this system the CBX-D5 is used with an Atari TT computer and the supporting

software is Cubase Audio by Steinberg.

What you will need

1) The CBX-D5, a power cable, two MIDI cables, a 50-way SCSI cable, and a SCSI

terminator (all these except for one MIDI cable are provided with the CBX-D5).

2) An Atari TT computer and an Atari video monitor.

3) Steinberg’s Cubase Audio software (Atari version).

4) A SCSI hard disk and a 25-pin D-SUB to 50-way SCSI cable.

Making the connections

1) Connect the Atari computer’s “MIDI OUT” connector to the CBX-D5’s “MIDI IN”

connector, and the computer’s “MIDI IN” connector to the CBX-D5’s “MIDI OUT”

connector using the MIDI cables.

2) Connect the Atari computer’s “SCSI” connector to the hard disk’s SCSI connector

using the 25-pin D-SUB to 50-way SCSI cable.

3) Connect the other hard disk SCSI connector to one of the CBX-D5’s SCSI

connectors using the 50-way SCSI cable.

4) Insert the CBX-D5’s SCSI terminator into the CBX-D5’s unused SCSI connector.

5) Connect the CBX-D5 to an AC receptacle using the supplied power cable.

6) Connect the Atari computer and its video monitor to an AC receptacle.

Settings

1) Set the CBX-D5 to SCSI ID “5 or 6” using the thumb wheel switch on the rear of the

CBX-D5.

2) Set the CBX-D5’s “TO HOST” switch to “MIDI”.

3) Set the hard disk to SCSI ID “1” (refer to its Operating Manual for details).

NOTE: Clinch the SCSI connector’s spring retaining clips and tighten the 25-pin

D-SUB connector’s locking screws for secure connections.

NOTE: 1. External hard disks must be set with continuous SCSI IDs starting

from 1 (1, 2, 3, 4…). The TT’s internal hard disk is set to ID 0.

2. Do not set the ID number of the CBX-D5 so that it is consecutive to

the ID number of the “HARD DISK”.

Switching on the power 5Switching on the power 5Switching on the power 5

Figure 2. System connections

Switching on the power

1) Switch on the SCSI devices: CBX-D5, hard disk.

2) Switch on the Atari computer and load Cubase Audio.

What to do next

• The SCSI hard disk must be formatted before it can be used (refer to the hard disk’s

Operating Manual). See also “Working with Hard Disks” on page 18 of the CBX-D5

Operating Manual.

• For recording and playback you should refer to the Cubase Audio Operating

Manuals. See also “Recording” on page 20 and “Playback” on page 23 of the

CBX-D5 Operating Manual.

Notes:

• Other MIDI devices can be connected in this system as shown in “MIDI” on page 30

of the CBX-D5 Operating Manual.

• For audio device connection, see “Inputs & Outputs Explained” on page 26 of the

CBX-D5 Operating Manual.

• For more details about SCSI hard disks and connecting extra disks, see “Connecting

Hard Disk Drives” on page 13 of the CBX-D5 Operating Manual.

• The Atari TT’s internal hard disk should be used to store your computer software and

data such as Cubase Audio, MIDI song ﬁles, etc., and the external hard disk should

beusedpurelyforrecordingCBX-D5soundﬁles.Anexternalharddiskmustbeused

in this system, because it supplies the termination power that is required by the SCSI

bus.

ATARI

CBX-D5

HARD

DISK

MIDI IN

MIDI OUT

SCSI

TERMINATOR

POWER

CABLE

POWER

CABLE

SCSI

50-WAY SCSI

CABLE

POWER

CABLE

25-pin DSUB to

50-WAY SCSI CABLE

MIDI IN

MIDI OUT

MIDI CABLES

6 Chapter 4 : Digital Performer & Apple Macintosh System6 Chapter 4 : Digital Performer & Apple Macintosh System6 Chapter 4 : Digital Performer & Apple Macintosh System

4 Digital Performer & Apple Macintosh System

An overview

In this system the CBX-D5 is used with an Apple Macintosh computer and the

supporting software is Digital Performer by Mark of the Unicorn.

What you will need

1) The CBX-D5, a power cable, two MIDI cables, a 50-way SCSI cable, and a SCSI

terminator (all these except for one MIDI cable are provided with the CBX-D5).

2) An Apple Macintosh computer and a video monitor recommended by your dealer.

3) Mark of the Unicorn’s Digital Performer software (Macintosh version).

4) A SCSI hard disk and a 25-pin D-SUB to 50-way SCSI cable.

5) An external MIDI interface.

Making the connections

1) Connect either the Mac’s Modem or printer ports to the external MIDI interface.

Then connect one of the “MIDI OUT” connectors on the interface to the CBX-D5’s

“MIDI IN” connector, and the “MIDI IN” connector on the interface to the

CBX-D5’s “MIDI OUT” connector using the MIDI cables.

2) Connect the Mac’s 25-pin “SCSI” connector to one of the hard disk’s SCSI

connectors using the 25-pin D-SUB to 50-way SCSI cable.

3) Connect the other hard disk SCSI connector to one of the CBX-D5’s SCSI

connectors using the 50-way SCSI cable.

4) Insert the CBX-D5’s SCSI terminator into the CBX-D5’s unused SCSI connector.

5) Connect the CBX-D5 to an AC receptacle using the supplied power cable.

6) Connect the Mac and its video monitor to an AC receptacle.

Settings

1) Set the CBX-D5 to SCSI ID “1” using the thumb wheel switch on the rear of the

CBX-D5.

2) Set the “TO HOST” switch on the CBX-D5 to MIDI.

3) Set the hard disk to SCSI ID “2” (refer to its Operating Manual for details).

NOTE: Clinch the SCSI connector’s spring retaining clips and tighten the 25-pin

D-SUB connector’s locking screws for secure connections.

Switching on the power 7Switching on the power 7Switching on the power 7

Figure 3. System connections

Switching on the power

1) Switch on the SCSI devices: CBX-D5, hard disk.

2) Switch on the Mac and load Digital Performer.

What to do next

• The SCSI hard disk must be formatted before it can be used (refer to the hard disk’s

Operating Manual). See also “Working with Hard Disks” on page 18 of the CBX-D5

Operating Manual.

• For recording and playback you should refer to the Digital Performer Operating

Manuals. See also “Recording” on page 20 and “Playback” on page 23 of the

CBX-D5 Operating Manual.

Notes:

• Other MIDI devices can be connected in this system as shown in “Mac” on page 31

of the CBX-D5 Operating Manual.

• For audio device connection, see “Inputs & Outputs Explained” on page 26 of the

CBX-D5 Operating Manual.

• For more details about SCSI hard disks and connecting extra disks, see “Connecting

Hard Disk Drives” on page 13 of the CBX-D5 Operating Manual.

SCSISCSI

APPLE

MAC

CBX-D5

HARD

DISK

MODEM/

PRINTER

PORT

Label

SCSI PORT

50-WAY to 25-PIN

SCSI CABLE

SCSI

TERMINATOR

50-WAY SCSI

CABLE

POWER

CABLE

POWER

CABLE

MIDI IN

POWER

CABLE

MAC MIDI

INTERFACE

MIDI OUT

8-PIN MINI

DIN CABLE

MIDI OUT

MIDI IN

Andere Handbücher für CBX-D5

Inhaltsverzeichnis

Andere Yamaha Prozessor Handbücher

Beliebte Prozessor Handbücher anderer Marken

FALCON THREE

FALCON THREE TV SDI Bedienungsanleitung

Vdwall

Vdwall LVP8601 Bedienungsanleitung

Pro ceed

Pro ceed PDP 3 Bedienungsanleitung

Intel

Intel ARCHITECTURE IA-32 Bedienungsanleitung

Fastwel

Fastwel CPC310 Bedienungsanleitung

Usl

Usl JSD-60 Bedienungsanleitung

ALLEN & HEATH

ALLEN & HEATH DR128 Bedienungsanleitung

Harman Kardon

Harman Kardon AVP-2 Bedienungsanleitung

dbx

dbx Zone Pro 640 Bedienungsanleitung

Fastwel

Fastwel CPC309 Bedienungsanleitung

BBE

BBE 822 Bedienungsanleitung

NAIM

NAIM AV2 Bedienungsanleitung

GrandTec

GrandTec Grand Magic Guard III Bedienungsanleitung

Intel

Intel 80386 Kurzanleitung

TECshow

TECshow DSP-2600 W Bedienungsanleitung

Topp Music Gear

Topp Music Gear RT-DRIVE DLM-206 Bedienungsanleitung

NEC

NEC IPS-4000 Bedienungsanleitung

Texas Instruments

Texas Instruments Sitara AM335x Bedienungsanleitung