Yamaha PM1D Manager V2 Anleitungen und Rezepte

PM1D System Software V1.4 Supplementary Manual

Contents

New functionality in system software V1.4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Digital gain for input channels / insert inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Digital gain added to 2TR IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

BALANCE control for input channels / ST IN channels . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Temporary monaural setting for paired input channels / ST IN channels . . . . . . . . . . . . 9

Front panel operating procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Screen operating procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Operation when monaural is selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

M/S decoding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Tracking Recall function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

New functionality in system software V1.4

Thank you for purchasing the CS1D. This booklet

explains the functionality that was added or changed in

version 1.4 of the PM1D software.

New functionality in system software V1.4

The following functionality and speciﬁcations have been

added in version 1.4 of the PM1D system software.

•

Digital gain has been added to input channels/

insert inputs

Digital gain has been added to input channels and

insert inputs, allowing you adjust the input sensitiv-

ity in the digital domain. Digital gain can be used in

input channels and insert inputs to which an AD

card, digital I/O card, 2TR IN, GEQ, or EFF are

assigned.

Digital gain has been added to the six 2TR IN inputs.

The sensitivity of the signal that is input to each 2TR

IN can be adjusted in the digital domain, indepen-

dently for L and R.

•

BALANCE has been added to PAN mode of the

input channels

The PAN parameter of an input channel can now be

switched to a BALANCE parameter.

For adjacent odd-numbered/even-numbered input

channels, you can switch the PAN parameter to a

BALANCE parameter.

•

New capability to temporarily set paired input

channels/ST IN channels to monaural

The signals from paired input channels or ST IN

channels can now be converted into monaural. As

the monaural conversion method, you can select L-

MONO (only the signal of the odd-numbered chan-

nel), R-MONO (only the signal of the even-num-

bered channel), or L,R-MONO (the signals of both

channels mixed).

•

M/S decoding functionality

“M/S decoding functionality” has been added, allow-

ing a two-channel signal input from a MS mic to be

converted into a L/R signal

•

Tracking Recall function

The newly added “Tracking Recall” function lets you

add a previously-speciﬁed offset value to the value of

each fader when you recall a scene.

Changes

•

In the PAN/ROUTING function CH to MIX

screen, the send level knob to the MATRIX bus is

now displayed in gray to match the color of the

encoder on the CS1D. This makes it easier to dis-

tinguish the MIX send level knob from the send

level knob of the MATRIX/ST ROUTING func-

tion that sends the signal to the MATRIX bus.

•

The rotational angle of the encoder-type knobs in

the screen now matches the angle of the encoder

knobs of the CS1D front panel. The index mark-

ings have changed in conjunction with this.

•

Since V1.4 adds BALANCE to the PAN mode, the

line in the screen that indicates the encoder knob

position is now displayed in red for PAN (same as

before) and white for BALANCE, to make it eas-

ier to distinguish the setting. In the MATRIX/ST

function MATRIX/ST ROUTING screen as well,

the encoder knob positions are displayed in red

for PAN (same as before) and white for BAL-

ANCE.

Digital gain for input channels/insert inputs

Digital gain has been added to input channels or insert

inputs that are assigned to AD cards, digital I/O cards,

2TR IN, GEQ, or EFF. By using this, the input sensitivity

can be adjusted in the digital domain even for input

sources that do not have an analog head amp.

Since digital gain has been added, the input channel/

insert input displays in the IN HA/INSERT, IN CH

VIEW, INPUT UNIT, and MONITOR A/MONITOR B

screens have changed as follows.

■

If an AD card (LMY4-AD) is assigned

Digital gain

PM1D Manager for Windows Operating manual

■

If a digital I/O card (MY card) is assigned

■

If 2TR IN is assigned

■

If the output of an effect return is assigned

■

If a GEQ output is assigned

Digital gain can be used to adjust the input sensitivity in

a range of +10 dB– –20 dB (the knob will not turn any

further to the right beyond –20 dB).

Only in the case of the digital gain for an input channel,

you can also use the [GAIN] encoder of the CS1D's

INPUT block to adjust the setting. In this case as well,

the adjustable range for the input is +10 dB– –20 dB (the

knob will not turn any further to the right beyond –20

dB). Internally, the input sensitivity is adjusted in a gain

range of –10 dB to +20 dB. If you want a digital source to

be input at nominal level, set the GAIN knob in the

screen to 0 dB.

If a mic/line input card (LMY2-ML) is assigned to

an input channel/insert input, the screen will show

an analog gain knob (range: +10 dB– –68 dB), just

as in the previous software version.

If TB (talkback) is assigned to an input channel/

insert input, the input level will be adjusted by the

panel TALKBACK [LEVEL] volume, just as in the

previous software version.

Digital gain

GAIN

-68+10

GAIN

-68+10

Digital gain for input channels/insert inputs

If 2TR IN is assigned to an input channel/insert

input, the gain settings of the 2TR IN screen and

the HA/INSERT screen will be linked. These set-

tings cannot be set to different positions.

The digital gain of an input channel/insert input to

which 2TR IN is assigned will not be saved in the

scene memory.

Hint

Settings for the digital gain of an input card are saved

in the unit library. Also, if the UNIT parameters of

the corresponding channel are set to Recall Safe, the

Recall Safe setting will also apply to the digital gain of

the input card.

Settings for the digital gain of EFF/GEQ are saved in

the scene memory. If the corresponding internal

effect/GEQ is set to Recall Safe, the Recall Safe setting

will also apply to the digital gain of the correspond-

ing EFF/GEQ.

Procedure

To adjust the digital gain of an input channel/insert

input, use the following procedure.

1. In the INPUT PATCH screen (IN PATCH function),

assign either an ML card or a source other than TB

to the desired input channel/insert input.

2. Access the corresponding screen of the IN HA/

INSERT function.

The following illustration shown an example of

when an AD card (LMY4-AD) is assigned to the

input channel/insert input.

3. Move the cursor to the GAIN knob in the screen,

and turn the [DATA] encoder to adjust the digital

gain.

In the case of an input channel, you can also use the

[GAIN] encoder in the INPUT block of the CS1D, or

the [GAIN] encoder in the SELECTED INPUT

CHANNEL block.

4. If you want to link the gain setting of adjacent

channels, click GAIN GANG switch to turn it on.

If the GAIN GANG button is on, adjacent odd-num-

bered/even-numbered channels will have their gain

setting linked (while maintaining the offset value).

You can also use the GAIN GANG button to link

analog gain and digital gain. However, when either

the analog gain or the digital gain reaches the limit

of its adjustment, neither channel will be adjustable

beyond this point.

PM1D Manager for Windows Operating manual

Digital gain added to 2TR IN

Digital gain has been added to the six 2TR IN inputs,

allowing you to adjust the input sensitivity in the digital

domain. The sensitivity of the signal that is input to each

2TR IN can be adjusted independently for L and R.

In conjunction with this, the display in the 2TR IN

screen (MON/CUE function) has changed as follows.

Hint

Digital gain is valid even if ANALOG is selected as

the source for 2TR IN 1 or 2TR IN 2. In this case, the

setting adjusts the sensitivity after AD conversion.

BALANCE control for input channels/ST IN channels

As necessary, you can now control the BALANCE

parameter instead of the PAN parameter for adjacent

odd-numbered/even-numbered input channels or ST IN

channels.

To do this, access the PAN/ROUTING function CH to

MIX screen, and turn on the PAN MODE section BAL-

ANCE button.

When the BALANCE button is on, the signal ﬂow from

those two channels to the various buses will change as

follows.

■

STEREO bus

The PAN parameter that sends the signal to the STEREO

bus will change to a BALANCE parameter. (A BAL knob

will be displayed instead of a PAN knob in the PAN/

ROUTING function CH to MIX screen.)

In this case, the signal of the odd-numbered input chan-

nel will be sent only to the L channel, and the signal of

the even-numbered input channel will be sent only to

the R channel. The BAL knob will adjust the volume of

the two channels in tandem.



BALANCE button

STEREO L

STEREO R

BALANCE

INPUT CHANNEL 1

INPUT CHANNEL 2

BALANCE control for input channels/ST IN channels

■

VARI type MIX bus

If a VARI type MIX bus is paired, the PAN parameter of

the MIX bus will change to a BALANCE parameter. (A

BAL knob will be displayed instead of a PAN knob in the

PAN/ROUTING function CH to MIX screen.)

In this case, the signal of the odd-numbered input chan-

nel will be sent only to the odd-numbered MIX bus, and

the signal of the even-numbered input channel will be

sent only to the even-numbered MIX bus. The BAL

knob will adjust the volume of the two signals in tan-

dem.

In addition, if the VARI PAN LINK button is on for

either of these two channels, the MIX bus BAL knob will

be linked with the STEREO bus BAL knob. If you oper-

ate either BAL knob of the STEREO bus or MIX bus, the

remaining three BAL knobs will operate in tandem.

Hint

Even if the BALANCE button is on, the signal that is

sent from those input channels to a VARI type MIX

bus will not be affected unless the MIX bus is paired.

■

FIX type MIX bus

If the FIXED MIX PAN button is on for either of the two

channels whose PAN MODE is set to BALANCE, the sig-

nal that ﬂows from the corresponding input channel

through the BALANCE parameter will be sent to the FIX

type MIX bus. At this time, the signal of the odd-num-

bered input channel will be sent only to the odd-num-

bered MIX bus, and the signal of the even-numbered

input channel will be sent only to the even-numbered

MIX bus.

BAL knob

MIX 1 (VARI)

MIX 2 (VARI)

BALANCE

INPUT CHANNEL 1

INPUT CHANNEL 2

STEREO L

STEREO R

INPUT CHANNEL 1

INPUT CHANNEL 2 BALANCE

STEREO L

STEREO R

MIX 1

MIX 2

PM1D Manager for Windows Operating manual

Hint

Even if the BALANCE button is on, the signal that is

sent from those input channels to a FIX type MIX

bus will not be affected if the FIXED MIX PAN but-

ton is turned off for both channels.

In addition, the operation will change as follows if the

PAN MODE “BALANCE” button is on.

•

Of the two channels for which the BALANCE button

is turned on, if you save one of the channels in the

channel library, the PAN MODE setting will be saved

for the other channel even if it is not paired.

•

When you recall data from the channel library, the

PAN MODE or PAN value will not be recalled if the

PAN MODE setting differs between the recall source

and recall destination. However only if the recall des-

tination is paired, the PAN MODE and PAN value

will be recalled.

•

When you copy channel data, the PAN MODE and

PAN value will not be copied if the PAN MODE set-

ting differs between the copy source and copy desti-

nation. However, the PAN MODE and PAN value

will be copied only if the copy destination is paired.

•

When recalling a channel library or copying a chan-

nel, if the channel that is not being recalled or copied

is set to a PAN mode of BALANCE or if VARI PAN

LINK is turned on, the MIX “BALANCE” value will

be the same as the TO ST “BALANCE” in order to

avoid inconsistencies between the TO ST value and

MIX BALANCE value of the recalled or copied chan-

nels.

•

When recalling scene data from a scene memory, and

the PAN MODE setting of odd-numbered/even-

numbered input channels does not match because

one of the channels is set to Recall Safe, the PAN

MODE or PAN values will not be recalled.

•

For an input channel whose MIX send is set to Recall

Safe, the PAN/BALANCE of the MIX send will also

be subject to Recall Safe. For this reason if the PAN

MODE settings of the recall source and recall desti-

nation do not match, it will not be possible to recall

the PAN MODE or PAN/BALANCE values.

•

In the case of an input channel in which the PAN

MODE is BALANCE and the MIX send is set to

Recall Safe, recalling a scene in which “PAN

MODE=BALANCE,VARI PAN LINK=on” will cause

the BALANCE value of the STEREO send to be

recalled, but the BALANCE of the MIX send will be

subject to Recall Safe. In this state, it is possible that

BALANCE values of the STEREO send and MIX

send will be inconsistent, so VARI PAN LINK will

therefore be forcibly switched off. The PAN parame-

ter fade function (INPUT CH PANNING, located in

the SCENE function FADE TIME screen) can also be

used when the BALANCE button is on. However,

you must enable INPUT CH PANNING for both the

odd-numbered and even-numbered channels.

•

If the PAN MODE is switched from PAN to BAL-

ANCE (or vice versa) while the PAN parameter fade

function is being executed, the PAN parameter fade

function will be aborted for that channel.

Procedure

Here's the procedure for operating the BALANCE

parameter of input channels/ST IN channels.

1. Access the PAN/ROUTING function CH to MIX

screen.

2. In the VARI & FIX area, turn on the TO ST button

for adjacent odd-numbered/even-numbered chan-

nels or for a ST IN channel.

3. In the PAN MODE area, turn on the BALANCE but-

ton of the corresponding channels.

The PAN knobs in the screen (position indicator dis-

played in red) will change to BAL knobs (position

indicator displayed in white), and will function as

the balance parameter.

Hint

The BALANCE parameter is valid even if you do not

enable pairing between the input channels.

4. Move the cursor to one of the BAL knobs, and turn

the [DATA] encoder to adjust the value of the BAL-

ANCE parameter.

The BAL knobs of both channels will move in tan-

dem.

The BALANCE parameter can also be controlled

from the INPUT block [PAN] encoder on the CS1D's

front panel, or from the SELECTED INPUT CHAN-

NEL block [PAN] encoder. In this case, the LEDs sur-

rounding the [PAN] encoder will display as follows.

Temporary monaural setting for paired input channels/ST IN channels

The input signal from paired input channels or ST IN

channels can now be temporarily converted to monau-

ral. You can select one of the following three modes.

■

Set to L-MONO

The channels will remain paired, but the signal will tem-

porarily become a monaural signal containing only the

odd-numbered channel.

The [ON] switch of the even-numbered channel will be

forced off, and the PAN (BALANCE) of the odd-num-

bered channel will be set to the center.

■

Set to R-MONO

The channels will remain paired, but the signal will tem-

porarily become a monaural signal containing only the

even-numbered channel.

The [ON] switch of the odd-numbered channel will be

forced off, and the PAN (BALANCE) of the even-num-

bered channel will be set to the center.

■

Set to LR-MONO

The channels will remain paired, but the signal will tempo-

rarily become a monaural signal containing both channels.

The PAN (BALANCE) of both channels will be set to the

center.

PAN

Odd-numbered (L) channel Even-numbered (R) channel

Value of the BALANCE parameter

Always litAlways lit

Fixed at OFF

STEREO L

STEREO R

INPUT CHANNEL 1

INPUT CHANNEL 2

PAN=CENTER

When PAN MODE is other than BALANCE

STEREO L

STEREO R

INPUT CHANNEL 1

INPUT CHANNEL 2

BALANCE=CENTER

When PAN MODE is BALANCE

Fixed at OFF

STEREO L

STEREO R

INPUT CHANNEL 1

INPUT CHANNEL 2 PAN=CENTER

Fixed at OFF

When PAN MODE is other than BALANCE

STEREO L

STEREO R

INPUT CHANNEL 1

INPUT CHANNEL 2 BALANCE=CENTER

When PAN MODE is BALANCE

Fixed at OFF

STEREO L

STEREO R

INPUT CHANNEL 1

INPUT CHANNEL 2

PAN=CENTER

When PAN MODE is other than BALANCE

STEREO L

STEREO R

INPUT CHANNEL 1

INPUT CHANNEL 2

BALANCE=CENTER

When PAN MODE is BALANCE

PM1D Manager for Windows Operating manual

Even if L-MONO or R-MONO is selected, you can

edit the parameters of the channel that was forced

off. (However, the [ON] switch will be ﬁxed at Off

until you defeat the L-MONO or R-MONO setting,

and cannot be changed.)

A new preference setting [L,R-MONO SELECT ON

PANEL] has been added to the UTILITY function

PREFERENCE screen, allowing you to switch to the

LR-MONO setting from the front panel.

In previous versions of the system software, it was

always possible to switch between PAIR and

MONO from the front panel. However, a new pref-

erence setting [PROHIBIT PAIR CHANGE ON

PANEL] has been added to the UTILITY function

PREFERENCE screen, allowing you to enable/dis-

able this function from being operated from the

front panel.

Front panel operating procedure

Here's how paired input channels/ST IN channels can be

temporarily set to monaural from the front panel.

1. Access the UTILITY function PREFERENCE

screen, and turn on the L,R-MONO SELECT ON

PANEL button.

This allows the temporary change from stereo to

monaural to be made from the front panel.

2. Specify pairing for any two adjacent odd-num-

bered/even-numbered input channels.

3. Use the front panel [SEL] switches and [SHIFT]

switches to select one of the following three ways in

which the channels will be temporarily set to mon-

aural.

•While holding down the [SHIFT]

switch Press and hold the [SEL]

switch of the odd-numbered (L)

channel

......................................... select L-MONO

•While holding down the [SHIFT]

switch Press and hold the [SEL]

switch of the even-numbered (R)

channel

........................................ select R-MONO

•While holding down the [SHIFT]

switch Press and hold the [SEL]

switches of both channels

............select LR-MONO

For the [SHIFT] switch described above, you may use

any of the [SHIFT] switches in CHANNEL SELECT sec-

tion of the SELECTED INPUT CHANNEL block or

SELECTED OUT CHANNEL block, or the [SHIFT]

switch of the data entry block.

You can use the same procedure as described above to

change one temporary monaural setting to a different

temporary monaural setting.

On the panel, the INPUT [NAME] indicator will blink

alternately between the name of the channel that was set to

temporary monaural and the name of the monaural mode.

For a channel that is turned off, the INPUT [NAME] indi-

cator will dimly display the channel name. The [NAME]

indicator will also be displayed in the same way when these

channels are recalled to a DCA fader. For details on opera-

tion when a monaural setting is selected, refer to page 11.

• Name indicator

For L-MONO:

L ch: Alternately display

and the chan-

nel name (the brightness depends on the

on/off status)

R ch: Alternately display and the chan-

nel name (dimly)

For R-MONO:

L ch: Alternately display and the chan-

nel name (dimly)

R ch: Alternately display and the chan-

nel name (the brightness depends on the

on/off status)

For LR-MONO:

L ch: Alternately display

and the chan-

nel name (the brightness depends on the

on/off status)

R ch: Alternately display

and the chan-

nel name (the brightness depends on the

on/off status)

4. To defeat the temporary monaural setting, press

the same combination of switches as you pressed in

step 3.

L ch R ch

Andere Handbücher für PM1D Manager V2

Inhaltsverzeichnis

Andere Yamaha Software Handbücher

Yamaha

Yamaha Studio Manager v.2 Bedienungsanleitung

Yamaha

Yamaha mLAN Driver Bedienungsanleitung

Yamaha

Yamaha DME Designer Bedienungsanleitung

Yamaha

Yamaha DME-N Bedienungsanleitung

Yamaha

Yamaha LS9-16 Bedienungsanleitung

Yamaha

Yamaha Audio Bedienungsanleitung

Yamaha

Yamaha Studio Manager Bedienungsanleitung

Yamaha

Yamaha DM 1000 Bedienungsanleitung

Yamaha

Yamaha IMX644 Manager Bedienungsanleitung

Yamaha

Yamaha TOOLS for MY16-mLAN Bedienungsanleitung

Yamaha

Yamaha M7CL StageMix V1.5 Bedienungsanleitung

Yamaha

Yamaha Acoustic Bedienungsanleitung

Yamaha

Yamaha EZ-220 Page Turner Bedienungsanleitung

Yamaha

Yamaha DM 1000 Bedienungsanleitung

Yamaha

Yamaha Card Filer Bedienungsanleitung

Yamaha

Yamaha VL Bedienungsanleitung

Yamaha

Yamaha CL1 Bedienungsanleitung

Yamaha

Yamaha CS6R Bedienungsanleitung

Yamaha

Yamaha CL3 Bedienungsanleitung

Yamaha

Yamaha 02R96 Version 2 Handbuch

Yamaha

Yamaha MagicStomp Bedienungsanleitung

Yamaha

Yamaha S90 Bedienungsanleitung

Yamaha

Yamaha USB Bedienungsanleitung

Yamaha

Yamaha YC-3B Bedienungsanleitung

Beliebte Software Handbücher anderer Marken

COMPRO

COMPRO COMPROFM Bedienungsanleitung

Muratec

Muratec OFFICEBRIDGE ONLINE Bedienungsanleitung

Oracle

Oracle Contact Center Anywhere 8.1 Bedienungsanleitung

Adobe

Adobe 65007312 - Photoshop Lightroom Handbuch

Avaya

Avaya NULL One-X for RIM Blackberry Bedienungsanleitung

HP ProLiant BL420c Bedienungsanleitung

PS Audio

PS Audio PowerPlay Betriebsanleitung

Brady

Brady LOCKOUT PRO 3.0 Service-Handbuch

Avaya

Avaya Interaction Center Bedienungsanleitung

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Handbuch

Novell

Novell GROUPWISE 8 - INTERNET AGENT Bedienungsanleitung

Oracle

Oracle Application 9i Bedienungsanleitung

Acer

Acer RDM Bedienungsanleitung

Canon

Canon Vixia HF21 Bedienungsanleitung

Canon

Canon ZR950 Bedienungsanleitung

Samsung

Samsung Auto Backup Bedienungsanleitung

Polycom

Polycom Vortex EF2201 Montage- und Bedienungsanleitung

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Bedienungsanleitung