Yamaha RX-V2065 - AV Network Receiver Gebrauchs- und Pflegehandbuch

Firmware Update Procedure for RX-V2065

Page.1 of 7

October, 2010

Subject: RX-V2065 Firmware Update ver. 036.104.037

Yamaha is pleased to offer this firmware update to ensure the best possible

performance for your Yamaha RX-V2065 AV Receiver.

This firmware improves network connectivity.

The following pages contain the firmware update instructions for RX-V2065. You can

easily update to the latest firmware by either using an USB thumb drive or through

internet. In order to properly execute the update, read all instructions carefully. The

following links will also lead you directly to the beginning of each individual section of

the instructions.

9Click here to confirm your current firmware version.

9Click here to firmware update by USB. (USB thumb drive required)

Update by Network is recommended if your receiver is connected to the internet.

9Click here to firmware update by Network. (Internet connection required)

9Click here to confirm updated firmware version

9Click here for troubleshooting.

< IMPORTANT NOTICE >

Do not attempt to update your Yamaha receiver using any other data file except those provided

directly from the Yamaha website or through your network connection.

Follow the instructions carefully and do not attempt any other procedures not specified in the

instructions provided by Yamaha.

Improperly updated products may cause improper operation, and any parts or service required

to restore proper operation will not be covered under the Yamaha Limited Warranty.

Firmware Update Procedure for RX-V2065

Page.2 of 7

Confirming Firmware Version

Below are the procedures to confirm your firmware version.

Step1 Enter ADVANCED SETUP mode

Confirm that your receiver is powered off. (Standby condition)

While pressing the STRAIGHT button, press (and release) the MAIN ZONE

button and keep depressing the STRAIGHT button until “ADVANCED

SETUP” appears on the front panel display.

(Note: “ADVANCED SETUP” is displayed only for a few seconds.)

Step2 Select Version display from the menu

Rotate the PROGRAM selector counterclockwise and select “VER”.

Latest version would be “VER036.104.037”.

“036”, “103” and “034” each represents the version of several programs in

your receiver.

If your receiver’s version is lower than above, perform firmware update

described in the following pages.

If “ERROR” appears, refer to the troubleshooting methods on page 7 to

recover.

MAIN ZONE

PROGRAM STRAIGHT

Firmware Update Procedure for RX-V2065

Page.3 of 7

Firmware Update by USB

Step1 Prepare USB thumb drive for the update

Download the firmware and unzip the file. Copy “RX-V2065_xxxx.bin”

into the root directory of the USB thumb drive.

Step2 Power off the receiver. (Standby condition). Then, insert the USB thumb

drive to the USB terminal located on the front panel.

Step3 Enter ADVANCED SETUP mode

While pressing the STRAIGHT button, press (and release) the MAIN ZONE

ON/OFF button and keep depressing the STRAIGHT button until

“ADVANCED SETUP” appears on the front panel display.

(Note: “ADVANCED SETUP” is displayed only for a few seconds.)

Requirement: - USB thumb drive, with enough free space to store over 16 MB.

(File system with FAT16 or FAT32 format)

- Firmware file provided by YAMAHA,”RX-V2065_xxxx.bin”.

Drag & Drop the file into USB drive.

MAIN ZONE

STRAIGHT

USB Drive

Firmware Update Procedure for RX-V2065

Page.4 of 7

Step4 Select “USB FirmUpdate” from the menu

Rotate the PROGRAM selector counterclockwise and select

“USB FirmUpdate ”.

Step5 Start firmware update

Press STRAIGHT button to start update.

NOTE: Be aware that performing this update will clear all your receiver

setting back to factory default.

Firmware reprogramming in progress

CAUTION! DO NOT interrupt power or remove the USB thumb drive during the

update.

In case the power is accidentally cut off resulting in a condition where you

can’t recover normal operation, refer to troubleshooting method CASE#3

on page 7.

Step6 When completed, “UPDATE SUCCESS” appears on the display.

Turn off the power of the receiver by pressing MAIN ZONE button.

Remove USB thumb drive.

Step7 Check updated firmware version

Enter Advanced Setup mode and select “VER” on the menu.

(See “Confirming Firmware Version section” for details)

MAIN ZONE

STRAIGHT

PROGRAM

Firmware Update Procedure for RX-V2065

Page.5 of 7

Firmware Update by Network

Step1 Power off the receiver. (Standby condition).

Step2 Enter ADVANCED SETUP mode

While pressing the STRAIGHT button, press (and release) the MAIN ZONE

ON/OFF button and keep depressing the STRAIGHT button until

“ADVANCED SETUP” appears on the front panel display.

(Note: “ADVANCED SETUP” is displayed only for a few seconds.)

Requirement: Internet connection

Your receiver is connected to the internet if you can receive

internet radio stations. (see owner’s manual for details)

MAIN ZONE

STRAIGHT

Firmware Update Procedure for RX-V2065

Page.6 of 7

Step3 Select “NET FirmUpdate” from the menu

Rotate the PROGRAM selector counterclockwise and select

“NET FirmUpdate ”.

Step4 Start firmware update

Press STRAIGHT button to start update. “CHECKING….” will appear.

NOTE: Be aware that performing this update will clear all your receiver

setting back to factory default.

If “UPDATE UNAVAIL” appears, this means your receiver is already

up-to-date. In this case, power off to exit from Advanced Setup.

Firmware reprogramming in progress

Caution! DO NOT interrupt power during the update.

In case the power is accidentally cut off resulting in a condition where you

can’t recover normal operation, refer to troubleshooting method CASE#3

on page 7.

Step5 When completed, “UPDATE SUCCESS” appears on the display.

Turn off the power of the receiver by pressing MAIN ZONE button.

Step6 Check updated firmware version

Enter Advanced Setup mode and select “VER” on the menu.

(See “Confirming Firmware Version” section for details)

MAIN ZONE

STRAIGHT

PROGRAM

Firmware Update Procedure for RX-V2065

Page.7 of 7

Troubleshooting

Case #1: “UPDATE FAIL” appeared during the USB update.

Cause: For some reason, the receiver can’t read the firmware data.

For your solution, please check the following;

9USB drive is securely connected to the receiver.

9USB drive is inserted before the receiver is powered on for the update.

9The firmware data, RX-V2065_xxxx.bin is stored in the root directory of

the USB drive.

9There is no other data but the firmware data in the USB drive.

9No folders are created in the USB drive.

Else,

Retry the update using another USB drive.

Case #2: Error message appeared during the Network update.

“UPDATE FAIL” Solution: Perform USB update (See page 3)

“VER.CHECK ERR” Solution: Check your network environment

Case #3: Firmware update doesn’t start for other reasons.

Receiver doesn’t power up after the update.

Or, “ERROR” appeared when confirming the firmware version.

To recover, perform following alternative USB update method

1. Unplug the AC power cable from the back of the receiver.

2. Insert the USB thumb drive into the USB terminal located on the front panel.

(The firmware must be downloaded and copied into the USB drive in prior)

3. Press and hold the TONE CONTROL button and keep it pressed while you plug

the AC power cable back into the receiver again. “FILE READING” will appear

on the front display. Then, release the TONE CONTROL button.

4. The update will start automatically.

5. When “UPDATE SUCCESS” appears on the display, firmware update is

completed. Power off the receiver and remove the USB thumb drive.

6. Confirm updated firmware version.

TONE CONTROL

USB Drive

Andere Handbücher für RX-V2065 - AV Network Receiver

Inhaltsverzeichnis

Andere Yamaha Stereo-Receiver Handbücher

Yamaha

Yamaha R-500 Bedienungsanleitung

Yamaha

Yamaha RX-V530RDS Bedienungsanleitung

Yamaha

Yamaha CR-3020 Bedienungsanleitung

Yamaha

Yamaha RX-V383BL Bedienungsanleitung

Yamaha

Yamaha RX-V1085 Bedienungsanleitung

Yamaha

Yamaha RX-700U Bedienungsanleitung

Yamaha

Yamaha RX-V1900 Bedienungsanleitung

Yamaha

Yamaha RX-V573 Bedienungsanleitung

Yamaha

Yamaha CR-2040 Bedienungsanleitung

Yamaha

Yamaha 485RDS Bedienungsanleitung

Yamaha

Yamaha RX-485 Bedienungsanleitung

Yamaha

Yamaha RX-397 Bedienungsanleitung

Yamaha

Yamaha RX-V2090 Bedienungsanleitung

Yamaha

Yamaha RX-V2600 Bedienungsanleitung

Yamaha

Yamaha RX-300U Bedienungsanleitung

Yamaha

Yamaha RX-460 Bedienungsanleitung

Yamaha

Yamaha AVENTAGE RX-A1080BL Bedienungsanleitung

Yamaha

Yamaha RX-750 Bedienungsanleitung

Yamaha

Yamaha HTR-6230 Bedienungsanleitung

Yamaha

Yamaha MusicCast TSR-5B3D Bedienungsanleitung

Yamaha

Yamaha AVENTAGE RX-A680 Bedienungsanleitung

Yamaha

Yamaha Aventage RX-A3040 Kurzanleitung

Yamaha

Yamaha RX-V577 Bedienungsanleitung

Yamaha

Yamaha HTR-5790 Bedienungsanleitung

Beliebte Stereo-Receiver Handbücher anderer Marken

Marantz

Marantz CINEMA 70S Bedienungsanleitung

Kenwood

Kenwood KMDX92 Bedienungsanleitung

Pioneer

Pioneer AVH-Z7250BT Bedienungsanleitung

Denon

Denon AVR-1311 Bedienungsanleitung

Denon

Denon AVR-S760H Bedienungsanleitung

Denon

Denon AVR-X7200W Bedienungsanleitung

Pioneer

Pioneer SC-LX904 Handbuch

Sony

Sony XAV-1500 Bedienungsanleitung

Radio Shack

Radio Shack DX-399 Bedienungsanleitung

Sony

Sony STR-DE535 - Fm Stereo/fm-am Receiver Bedienungsanleitung

Pioneer

Pioneer SX-1000TA Bedienungsanleitung

Sony

Sony STR-DE335 - Fm Stereo/fm-am Receiver Bedienungsanleitung

Sony

Sony STR-DG500 - Multi Channel Av Receiver Bedienungsanleitung

Panasonic

Panasonic AJSD955B - DVCPRO50 STUDIO DECK Bedienungsanleitung

Pioneer

Pioneer SX-838 Bedienungsanleitung

Sherwood

Sherwood S-2660CP Technisches Handbuch

Sony

Sony STR-K790 - Lifier Bedienungsanleitung

Pioneer

Pioneer XR-VS77 Bedienungsanleitung