Yamato SPC - Solar Bedienungsanleitung
YCO-130607
SPC - Solar Operation Manual
YAMATO CORPORATION
1775 S. Murray Blvd.
Colorado Springs, CO 80916 USA
Tel (719) 591-1500 Fax (719) 591-1045
YAMATO TECH CORPORATION
#112-19425 Langley By-Pass
Surrey, B.C. V3S 6K1 Canada
Tel (604) 533-2338 Fax (604) 533-0827
www.YamatoCorp.com
Solar Powered
Portion Control Scale
SPC - Solar
Operation Manual
Read this manual before use and keep it handy
YCO-130607
SPC - Solar Operation Manual
Model Lower Range High Range Maximum Tare
SPC-Solar 2 0 - 2.2 lb x 0.002 lb
0 - 2 lb 3 oz x 0.05 oz
0 - 35 oz x 0.05 oz
0 - 1000 g x 1 g
2.2 - 4.4 lb x 0.005 lb
2 lb 3 oz - 44 lb 6oz x 0.1oz
35 - 70 oz x 0.1 oz
1000 - 2000 g x 2 g
2.190 lb
2 lb 2.75 oz
34.75 oz
995 g
SPC-Solar 5 0 - 5.5 lb x 0.05 lb
0 - 5 lb 8 oz x 0.1 oz
0 - 88 oz x 0.1 oz
0 - 2500 g x 2 g
5.5 - 11 lb x 0.01 lb
5 lb 8 oz - 11 lb 2 oz x 0.2 oz
88 - 178 oz x 0.2 oz
2500 - 5000 g x 5 g
5.475 lb
5 lb 7.5 oz
87.5 oz
2490 g
System Parameter
Operation Display
1
Press and hold the key and press + keys to
go to system parameter mode under the weighing mode.
The
indicator blinks during system parameter
indicator lights up
2 The operation under system parameter mode is as follows
: Move parameter No. forward (+1)
: Move setting value forward (+1)
: Move setting value backward (-1)
* Be sure to set the setting value among available
parameter values shown on the parameter list. When
the setting value you desire has passed, press the
key to move backwared (-1).
Long Press the key to turn off the power to save the
setting value in the memory
Product Specicatons
1
YCO-130607
SPC - Solar Operation Manual
Parameter List
2
( # 01 - 04: User parameter, # 05 - 09: System parameter)
Parameter Description Available parameter
01 Power Select 000:
001:
002:
Solar-powered operation (Default)
Battery-powered operation (Quick response)
Hybrid (Solar + Battery) operation
(The response speed is the same as 000)
02 Weighing units
at power on
000:
001:
002:
003:
g
lb (Default)
oz
lb.oz
03 Checkweighing
function
000:
001:
Disabled
Enabled (Default)
04 Auto-off timer 000:
001-009:
Disabled
Set by one minute (5 minute: Default)
05 Gravity
compensation
000:
001-029:
030-210:
Disabled
Prohibited to set
(Acceleration of Gravity (m/s2) - 9.7600) x 10000/5 + 30
(offset)
Setting range: 9.7600 to 9.8500 m/s2
Minimum setting unit: 0.0005 m/s2
06 Capacity 000:
001:
2000 g
5000 g
07 Zero tracking 000:
001:
Disabled
Enabled (Default)
08 Not used
09 Not used
YCO-130607
SPC - Solar Operation Manual
3
Calibration
Prepare "kilogram" check weights (more than OIML M1 class) corresponding to the capacity. It is not
possible to calibrate the SPC-Solar with either "pound" or "ounce" check weight. Be sure to calibrate the
scale under battery-powered mode.
Operation Display
1 Install batteries.
Set the user parameter No. 01 (power select) at 001
(battery-powered operation)
Press and hold the key and press the key to go
to user parameter mode.
2
Press and hold the key and press the key to go
to calibration mode
3
After conrming, the stable indicator lights up, press
the key.
4 Place a check weight corresponding to the scale
capacity.
SPC - Solar 2: 2,000 grams
SPC - Solar 5: 5,000 grams
5
When the stable indicator lights up, press key.
If the display shows as right gures, calibration has been
completed successfully
If there is the following differences for the values in the
right gures, turn off the power and try to calibrate it
again
SPC - Solar 2: more than +/- 5 counts
SPC - Solar 5: more than +/- 10 counts
After calibration, turn off the power. Turn on the power
again and conrm that correct weight value is displayed
Capacity 2 kg
Capacity 5 kg
YCO-130607
SPC - Solar Operation Manual
Error Messages
4
When one of the following error messages appears on the display, follow the troubleshooting instructions.
Contact the retailer from which the product was purchased, if other messages than the following appear,
or an error is not recovered after following the troubleshooting.
Display Cause Troubleshooting
Out of batteries
Batteries are running out. Replace all of the batteries
with new one. Do not use old
and new batteries or alkaline
and magnesium batteries at
a time.
The weight below zero
This message appears when
the weighed value is less
than - 5 divisions (- 5 g for the
weighing capacity of 2000 g).
Press the key.
If the pan has been removed,
set it on the scale again.
Overloading
This message appears when
the weighed value is over
+5 divisions (2010g for the
weighing capacity of 2000g).
When the item is removed,
the display returns to the
weighing screen. Make sure
to use the scale within the
capacity.
The initial error (A)
Turned on the scale while a
heavy item was placed
Remove the item from the
pan, and then press the
key
The initial error (B)
Turn on the scale while a
foreign material was stuck
between the main body and
the pan
Check if a foreign material is
not stuck or does not contact
the pan. Then press the
key.
The initial error (C)
Pressed the key while a
heavy item was on the pan in
the middle of the operation
The weight of the item is
beyond the level where the
key is operative.Remove
the item from the pan, and
then press the key.
The initial error (D)
Turned on the scale while
the item was left on a pan.
Remove the item and press
the key
Make sure that nothing is left
on the pan and turn on the
scale again.
YCO-130607
SPC - Solar Operation Manual
Wiring Diagram
5
YCO-130607
SPC - Solar Operation Manual
Parts List
6
YCO-130607
SPC - Solar Operation Manual
Parts List
7
Item Part # Description Qty / Unit
1 63910024 Platform Cover, S.S. 1
2 63910028 Plate, Platform Support 1
3 63910025 Cushion Rubber 4
4 63910020 Upper Housing 1
563910102 Load cell + PCB Assembly, 2 kg 1
63910103 Load cell + PCB Assembly, 5 kg 1
6 63911031 Battery Box 1
7 63900031 Battery Box Holder 1
8 63900032 Battery Lid with sponge 1
9 63900023 Holding Plate / CPU Board 1
10 63901034 Solar Panel 2
11 63900037 Membrane Key Switch 1
12 63900035 Front Mask, SPC - Solar 2 1
63910036 Front Mask, SPC - Solar 5 1
13 63910034 Solar Glass 2
14 63910033 Display Glass 1
15 63910021 Base 1
16 63910022 Rubber Foot 4
17,18,20,23,25 63911001 Hex Bolt & SW, M3X6, S.S. 17
19 63911002 Screw & Washer, M2X6 / Battery Box 2
21 63911003 Hex Bolt, M4X8, S.S. / Battery Lid 2
22 63911004 Screw & Washer, M3X6 / CPU Board 4
24 63911005 Hex Nut M4 / Rubber Foot 4
YCO-130607
SPC - Solar Operation Manual
YAMATO CORPORATION
1775 S. Murray Blvd.
Colorado Springs, CO 80916 USA
Tel (719) 591-1500 Fax (719) 591-1045
YAMATO TECH CORPORATION
#112-19425 Langley By-Pass
Surrey, B.C. V3S 6K1 Canada
Tel (604) 533-2338 Fax (604) 533-0827
www.YamatoCorp.com
Inhaltsverzeichnis
Andere Yamato Skala Handbücher
Yamato
Yamato AW-WPS Bedienungsanleitung
Yamato
Yamato CPC-2000 Bedienungsanleitung
Yamato
Yamato AW-300P Bedienungsanleitung
Yamato
Yamato PB-200 Bedienungsanleitung
Yamato
Yamato CPS series Bedienungsanleitung
Yamato
Yamato SPC-2002 Bedienungsanleitung
Yamato
Yamato Acuu-Weigh SPC-2002 Bedienungsanleitung
Yamato
Yamato SPC Series Bedienungsanleitung
Yamato
Yamato AW-WLG Series Bedienungsanleitung
Yamato
Yamato Accu-weigh PPC-200W Bedienungsanleitung
Yamato
Yamato Accu-weigh PPC-200 Bedienungsanleitung
Yamato
Yamato AW-WPS Bedienungsanleitung
Yamato
Yamato DP-6900 Bedienungsanleitung
Yamato
Yamato PPC-300WP Bedienungsanleitung
Yamato
Yamato PPC-101 Bedienungsanleitung
Yamato
Yamato DP-6700 Bedienungsanleitung
Yamato
Yamato PPC-200W Bedienungsanleitung
Yamato
Yamato DKS-3002 Bedienungsanleitung
Yamato
Yamato PPC-200 Bedienungsanleitung
Yamato
Yamato DP-6900 Bedienungsanleitung
