Yanmar 6LY3 series Bedienungsanleitung
Electronic Control System: Technical Manual for 6LY3 Series Engines
Electronic Control System
Technical Manual
for 6LY3 Series Engines
Revision 1.0
ii Electronic Control System: Technical Manual for 6LY3 Series
NOTICE TO INSTALLER
The WARNINGS and CAUTIONS within this manual are used to alert the installer to hazards that exist
concerning a particular service, operation or component. They also may convey special instructions to
reduce the risk of injury during the operation or servicing of the engine.
However, these safety alerts alone cannot eliminate the hazards that they signal. Strict compliance to
these
special instructions when performing installation, operation, and maintenance is the most effective ac-
cident prevention measure along with exercising care and using common sense when performing such
American Boat & Yacht Council (http://www.abycinc.org )
RECREATIONAL CRAFT DIRECTIVE 94/25/EC
This product has been designed to be compliant with the above Directive.
Maximum performance, and compliance with the EMC Directive, can only be ensured
by correct installation. It is strongly recommended that the installation conforms with
the following standards:
APPLICABLE STANDARDS
a) ISO 8846 Small Craft-Electrical Devices
Protection against ignition of surrounding flammable gases.
b) ISO = International Standards Organization
SAFE BOATING STATEMENT
This device meets or exceeds the applicable ABYC, ISO, and USCG safe boating rules,
regulations, standards, and guidelines.
SAFE BOATING ON THE WEB
U.S. Coast Guard www.uscg.mil
U.S. Power Squadron www.usps.org
NMEA 2000® is a regiatered trademark of the National Marine Electronics Association.
The information contained in this manual is believed to be accurate at the time of going to print but no responsibility, direct or consequential, can
be accepted for damage resulting from the use of this information. The manufacturers reserve the right to make changes, without notice, to any of
its products.
Electronic Control System: Technical Manual for 6LY3 Series Engines
Table of Contents
1. Components
2. System Overview
3. i5601E Digital Display
Specifications
Operators Interface
Maintenance Alarm
Main Menu
Change Set Up
4. Control Head
5. i83xx Engine Interface Module
Specifications
Pint-Outs
6. Gauges
i2000
Specifications
Connections
i2200
Specifications
Connections
7. System Default Settings
8. NMEA 2000® Network
9. System Diagrams
Single Engine CE415xx Engine Harness
Single Engine CE425xx Engine Harness
Dual Engine CE415xx Engine Harness
Dual Engine CE425xx Engine Harness
Power Diagram Outline
Power Diagram Single Engine
Power Diagram Dual Engine
10. Transmission Diagrams
Twin Disc
Twin Disc with Trolling
ZF
ZF with Trolling
11. Cable Information
CE415xx
CE405xx
CE404xx
CE425xx
CE42006
CE41906
CE42206
CE41800
CE40300
Rocker Switch Panel
Key Switch Panel
12. Deutsch Connectors
13. Mounting Templates
CH64600
CH67500
4400
5600
Palm Beach
i5601e Front Panel Mount
1st Station Ignition Panel – CP19100
i5601e Rear Panel Mount
1st Station Key Swtich Panel – CE40100
14. Troubleshooting
15. Parts Information
iv Electronic Control System: Technical Manual for 6LY3 Series
Electronic Control System: Technical Manual for 6LY3 Series Engines
vi Electronic Control System: Technical Manual for 6LY3 Series
1
Components
Electronic Control System: Technical Manual for 6LY3 Series Engines
Components
Engine Interface Modules
Dual CANBus Control Head
Digital Engine Displays (i5601E)
First Station Ignition Rocker Panels
Note: Key Switch Panel assemblies are also available.
The pin-outs are the same.
Note: Other style controls are also available.
2 Electronic Control System: Technical Manual for 6LY3 Series
2
System Overview
Electronic Control System: Technical Manual for 6LY3 Series Engines
System Overview
This electronic control system consists of the following equipment:
One Yanmar i5501E Digital Display per engine Shift & Throttle Control Head
Yanmar i5601E Digital Display
The unit displays real-time data as well as warnings or alarms for any engine abnormality. Diagnostic
codes are also displayed for use by Yanmar technicians.
Shift & Throttle Control Head
The Shift and Throttle Control Head selects the gear positions and the throttle settings. The Control
Head has several lights that confirm modes of operation and display warnings if present. Buttons enable
4 Electronic Control System: Technical Manual for 6LY3 Series
3
i5600 Digital Display
Andere Handbücher für 6LY3 series
3
Inhaltsverzeichnis
Andere Yanmar Motor Handbücher
Yanmar
Yanmar 6LYA-UTE Bedienungsanleitung
Yanmar
Yanmar 1GM10 Installationsanleitung
Yanmar
Yanmar 4JH45 Bedienungsanleitung
Yanmar
Yanmar 3TNM72-ASA3 Bedienungsanleitung
Yanmar
Yanmar 6LYA-UTE Bedienungsanleitung
Yanmar
Yanmar 6LPA-STP2 Bedienungsanleitung
Yanmar
Yanmar 3TNV Series Bedienungsanleitung
Yanmar
Yanmar 2TNV70-HGE Bedienungsanleitung
Yanmar
Yanmar 3YM30 Bedienungsanleitung
Yanmar
Yanmar 3QM30F Bedienungsanleitung
Yanmar
Yanmar 3JH5E Bedienungsanleitung
Yanmar
Yanmar 2TNV70 Bedienungsanleitung
Yanmar
Yanmar 6LYA-STP Bedienungsanleitung
Yanmar
Yanmar 6LPA-STP2 Bedienungsanleitung
Yanmar
Yanmar 4LHA-HTP Bedienungsanleitung
Yanmar
Yanmar 3YM30 Bedienungsanleitung
Yanmar
Yanmar 3JH5E Bedienungsanleitung
Yanmar
Yanmar 2TNV70 Bedienungsanleitung
Yanmar
Yanmar 6CXM-GTE Bedienungsanleitung
Yanmar
Yanmar 3JH4E Bedienungsanleitung
