YASKAWA Motoman DX200 Bedienungsanleitung

MANUAL NO.

HW1481819

Part Number: 165473-1CD

Revision: 0

DX200 OPTIONS

INSTRUCTIONS

FOR I/O OUTPUT TIMING CONTROL FUNCTION

Upon receipt of the product and prior to initial operation, read these instructions thoroughly, and retain

for future reference.

MOTOMAN INSTRUCTIONSNS

MOTOMAN- INSTRUCTIONS

DX200 INSTRUCTIONS

DX200 OPERATOR’S MANUAL

DX200 MAINTENACE MANUAL

The DX200 operator’s manual above corresponds to specific usage.

Be sure to use the appropriate manual.

1/24

165473-1CD

HW1481819

I/O Output Timing

Control

MANDATORY

• This manual explains the I/O output timing control function of the

DX200 system. Read this manual carefully and be sure to

understand its contents before handling the DX200.

• General items related to safety are listed in the Chapter 1: Safety of

the DX200 Instructions. To ensure correct and safe operation,

carefully read the DX200 Instructions before reading this manual.

CAUTION

• Some drawings in this manual are shown with the protective covers

or shields removed for clarity. Be sure all covers and shields are

replaced before operating this product.

• The drawings and photos in this manual are representative

examples and differences may exist between them and the

delivered product.

• YASKAWA may modify this model without notice when necessary

due to product improvements, modifications, or changes in

specifications. If such modification is made, the manual number will

also be revised.

• If your copy of the manual is damaged or lost, contact a YASKAWA

representative to order a new copy. The representatives are listed

on the back cover. Be sure to tell the representative the manual

number listed on the front cover.

• YASKAWA is not responsible for incidents arising from unauthorized

modification of its products. Unauthorized modification voids your

product’s warranty.

2/24

iii

165473-1CD

HW1481819

I/O Output Timing

Control

Notes for Safe Operation

Read this manual carefully before installation, operation, maintenance, or

inspection of the DX200.

In this manual, the Notes for Safe Operation are classified as

“WARNING”, “CAUTION”, “MANDATORY”, or ”PROHIBITED”.

Even items described as “CAUTION” may result in a serious accident in

some situations. At any rate, be sure to follow these important items.

WARNING

Indicates a potentially hazardous

situation which, if not avoided, could

result in death or serious injury to

personnel.

CAUTION

Indicates a potentially hazardous situa-

tion which, if not avoided, could result

in minor or moderate injury to person-

nel and damage to equipment. It may

also be used to alert against unsafe

practices.

MANDATORY

Always be sure to follow explicitly the

items listed under this heading.

PROHIBITED

Must never be performed.

NOTE

To ensure safe and efficient operation at all times, be sure to

follow all instructions, even if not designated as “CAUTION”

and “WARNING”.

3/24

165473-1CD

HW1481819

I/O Output Timing

Control

WARNING

• Before operating the manipulator, check that servo power is turned

OFF when the emergency stop buttons on the front door of the

DX200 and the programming pendant are pressed.

When the servo power is turned OFF, the SERVO ON LED on the

programming pendant is turned OFF.

Injury or damage to machinery may result if the emergency stop circuit

cannot stop the manipulator during an emergency. The manipulator

should not be used if the emergency stop buttons do not function.

Figure 1: Emergency Stop Button

• Once the emergency stop button is released, clear the cell of all

items which could interfere with the operation of the manipulator.

Then turn the servo power ON.

Injury may result from unintentional or unexpected manipulator motion.

Figure 2: Release of Emergency Stop

TURN

• Observe the following precautions when performing teaching

operations within the P-point maximum envelope of the

manipulator:

– View the manipulator from the front whenever possible.

– Always follow the predetermined operating procedure.

– Keep in mind the emergency response measures against the

manipulator’s unexpected motion toward you.

– Ensure that you have a safe place to retreat in case of

emergency.

Improper or unintended manipulator operation may result in injury.

• Confirm that no person is present in the P-point maximum envelope

of the manipulator and that you are in a safe location before:

– Turning ON the DX200 power

– Moving the manipulator with the programming pendant

– Running the system in the check mode

– Performing automatic operations

Injury may result if anyone enters the P-point maximum envelope of the

manipulator during operation. Always press an emergency stop button

immediately if there is a problem. The emergency stop buttons are

located on the right of the front door of the DX200 and the programming

pendant.

4/24

165473-1CD

HW1481819

I/O Output Timing

Control

Definition of Terms Used Often in This Manual

The MOTOMAN is the YASKAWA industrial robot product.

The MOTOMAN usually consists of the manipulator, the controller, the

programming pendant, and supply cables.

In this manual, the equipment is designated as follows:

CAUTION

• Perform the following inspection procedures prior to conducting

manipulator teaching. If problems are found, repair them

immediately, and be sure that all other necessary processing has

been performed.

– Check for problems in manipulator movement.

– Check for damage to insulation and sheathing of external wires.

• Always return the programming pendant to the hook on the DX200

cabinet after use.

The programming pendant can be damaged if it is left in the

manipulator’s work area, on the floor, or near fixtures.

• Read and understand the Explanation of the Warning Labels in the

DX200 Instructions before operating the manipulator.

Equipment Manual Designation

DX200 controller DX200

DX200 programming pendant Programming pendant

Cable between the manipulator and the

controller Manipulator cable

5/24

165473-1CD

HW1481819

I/O Output Timing

Control

Descriptions of the programming pendant keys, buttons, and displays are

shown as follows:

Description of the Operation Procedure

In the explanation of the operation procedure, the expression "Select • • • "

means that the cursor is moved to the object item and the SELECT key is

pressed, or that the item is directly selected by touching the screen.

Registered Trademark

In this manual, names of companies, corporations, or products are

trademarks, registered trademarks, or bland names for each company or

corporation. The indications of (R) and

are omitted.

Equipment Manual Designation

Programming

Pendant Character

Keys The keys which have characters printed on

them are denoted with [ ].

ex. [ENTER]

Symbol

Keys The keys which have a symbol printed on them

are not denoted with [ ] but depicted with a

small picture.

ex. page key

The cursor key is an exception, and a picture

is not shown.

Axis Keys

Numeric

Keys

“Axis Keys” and “Numeric Keys” are generic

names for the keys for axis operation and

number input.

Keys

pressed

simultaneou

sly

When two keys are to be pressed

simultaneously, the keys are shown with a “+”

sign between them, ex. [SHIFT]+[COORD]

Displays The menu displayed in the programming

pendant is denoted with { }.

ex. {JOB}

PAGE

GO BACK

PAGE

GO BACK

6/24

vii

165473-1CD

HW1481819

I/O Output Timing

Control

Table of Contents

1 About I/O Output Timing Control Function......................................................................................1-1

2 Setup of I/O Output Timing Control Function..................................................................................2-1

2.1 Instruction of I/O Output Timing Control Function .............................................................2-1

2.1.1 Configuration of Synchronized Signal Output Instruction at Move Instruction......2-1

2.1.2 Configuration of +DOUT Instruction .....................................................................2-2

2.1.3 Registration of +DOUT Instruction .......................................................................2-4

2.1.4 Configuration of +PULSE Instruction....................................................................2-8

2.1.5 Registration of +PULSE Instruction....................................................................2-10

2.2 Device Response Delay Time Compensate Parameter..................................................2-14

2.3 Signal Output Control Parameter During the FWD Operation........................................2-14

2.4 Notes ...............................................................................................................................2-14

2.5 The Examples of the I/O Output Timing Specifying Function..........................................2-15

7/24

1 About I/O Output Timing Control Function

1-1

165473-1CD

HW1481819

I/O Output Timing

Control

1 About I/O Output Timing Control Function

I/O output timing control function is a function that can adjust the timing of

general output signal by distance or time which based on the teaching

position for the move instruction.

When the manipulator reaches to the specifying point which specified the

time or distance while the manipulator is operating the move instruction,

this function can output the general output signal. This function can adjust

to deviation of work timing from the operation delay of the manipulator or

devices which controlled by general output signal such as, valve and

cylinder. Therefore, the manipulator can operate correctly, when it

reaches to the expected position.

Fig. 1-1: I/O Output Timing Control Function

NOTE

In case of the signal output is specified as distance, and the

manipulator does not reach to the signal output position,

such as the movement of the inward turning operation, the

signal will be outputted when the manipulator comes to

closest approach.

8/24

2-1

165473-1CD

HW1481819

I/O Output Timing

Control

2 Setup of I/O Output Timing Control Function

2.1 Instruction of I/O Output Timing Control Function

2 Setup of I/O Output Timing Control Function

2.1 Instruction of I/O Output Timing Control Function

2.1.1 Configuration of Synchronized Signal Output Instruction at Move

Instruction

On the I/O output timing control function, as shown in Table 2-1

Configuration of Synchronized Output Signal. The synchronized signal

output instruction (+DOUT/+PULSE) added to the move instruction will

output the general output signal. The configuration of instruction is shown

as follows.

Fig. 2-1: Configuration of Synchronized Output Signal

+DOUT

Synchronized signal output instruction

+PULSE

Synchronized pulse output instruction

ADJD=

Adjustment distance tag (setting data range: -3276.8 to 0.0[mm])

ADJT=

Adjustment time tag (setting data range: -3276.8 to 0.0[mm])

NOTE

The synchronized signal output instruction (+DOUT/

+PULSE) can be added four move instructions, as follows

MOVJ/MOVL/MOVC/IMOV

NOTE

The I/O output timing control function can only adjust timing

of the signal output to the previous direction (-direction)

against the teaching position. For the backward direction

(+direction) from the teaching position, operate the signal

output to adjust to the previous direction against the

teaching position of the next move instruction.

9/24

2 Setup of I/O Output Timing Control Function

2.1 Instruction of I/O Output Timing Control Function

2-2

165473-1CD

HW1481819

I/O Output Timing

Control

2.1.2 Configuration of +DOUT Instruction

+DOUT instruction which is added to the move instruction performs

adjustment to the output timing of the general output signal.

The additional item of the +DOUT instruction is shown as follows.

Fig. 2-2: Configuration of +DOUT

Choose of the tags from the following table

No Tag Explanation Note

1OT#

(Output No.) Specifies the output number signal. No:1 to 4096

Variable B/I/D/LB/LI/LD

can be used.

2 OG#

(Output group No.) Specifies the output number group signal

(1group 8 points). No:1 to 512

Variable B/I/D/LB/LI/LD

can be used.

3 OGH#

(Output group No.) Specifies the output number group signal

(1group 4 points). No:1 to 1024

Variable B/I/D/LB/LI/LD

can be used.

SUPPLE-

MENT

Output signal

Output signal OT#(x) is 1 point, OGH#(x) is 1 group 4 points,

and OG#(x) is 1 group 8 points.

㪦㪫㩺㩿㪏㪀㪦㪫㩺㩿㪎㪀㪦㪫㩺㩿㪍㪀㪦㪫㩺㩿㪌㪀㪦㪫㩺㩿㪋㪀㪦㪫㩺㩿㪊㪀㪦㪫㩺㩿㪉㪀㪦㪫㩺㩿㪈㪀

㪦㪞㪟㩺㩿㪉㪀㪦㪞㪟㩺㩿㪈㪀

㪦㪞㩺㩿㪈㪀

No Tag Explanation Note

4 B Variable number/

LB Variable number

B [Array number]/

LB [Array number]

The least significant bit of the specified byte type

variable specifies ON/OFF of the output signal. Least significant bit:

0: OFF

1: ON

5 ON/OFF Specifies ON/OFF of the output signal.

6 INVERT Refers the current signal status to output OFF when the

status is ON, and output ON when the status is OFF.

10/24

Andere Handbücher für Motoman DX200

Inhaltsverzeichnis

Andere YASKAWA Controller Handbücher

YASKAWA

YASKAWA JEPMC-EXU3001-E Bedienungsanleitung

YASKAWA

YASKAWA SI-EM3 Bedienungsanleitung

YASKAWA

YASKAWA Varispeed-616GII Bedienungsanleitung

YASKAWA

YASKAWA A1000 Series Bedienungsanleitung

YASKAWA

YASKAWA MP2000 Series Bedienungsanleitung

YASKAWA

YASKAWA E7 Drive Bedienungsanleitung

YASKAWA

YASKAWA CIMR-VC series Bedienungsanleitung

YASKAWA

YASKAWA 1000 Series Bedienungsanleitung

YASKAWA

YASKAWA MOTOMAN DX100 Bedienungsanleitung

YASKAWA

YASKAWA PROFIBUS-DP SI-P3 Bedienungsanleitung

YASKAWA

YASKAWA MP3300 series Bedienungsanleitung

YASKAWA

YASKAWA motoman NX100 Bedienungsanleitung

YASKAWA

YASKAWA Motoman DX200 Bedienungsanleitung

YASKAWA

YASKAWA AO-A3 Leitfaden

YASKAWA

YASKAWA 1000-Series Bedienungsanleitung

YASKAWA

YASKAWA MOTOMAN FS100 Bedienungsanleitung

YASKAWA

YASKAWA SGD7S-***A20****F62 Series Bedienungsanleitung

YASKAWA

YASKAWA MP2300Siec Bedienungsanleitung

YASKAWA

YASKAWA yasnac lx3 Bedienungsanleitung

YASKAWA

YASKAWA PROFIBUS-DP Bedienungsanleitung

YASKAWA

YASKAWA YRC1000 Bedienungsanleitung

YASKAWA

YASKAWA Z1000 CIMR-ZU*A Series Bedienungsanleitung

YASKAWA

YASKAWA FSDrive-MV1000 Series Bedienungsanleitung

YASKAWA

YASKAWA SI-EL3/V Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung