YASKAWA IQpump1000 Bedienungsanleitung

Technical Tip: How to Connect and Troubleshoot Transducer Feedback

Product(s): iQpump1000 and iQpump Micro Drives Doc. No. TN.iQp.03

Revision 1 July 8, 2015 Page 1 of 5

This Technical Tip assists users in applying Yaskawa iQpump1000 and iQpump Micro

products to pump systems and provides useful information on:

running without a transducer

fixing Fdb-L or Feedback Loss faults/alarms

proper transducer wiring

settings for voltage or current transducers

multiple transducer wiring

What feedback transducers work with iQpump?

Yaskawa’s iQpump1000 and iQpump Micro drives utilize transducer feedback to change

pump speed to optimize system efficiency and performance.

iQpump drives typically interface with either pressure, flow, and/or temperature transducers;

most commonly pressure transducers with a 4-20 mA output.

4-20 mA pressure transducers have a maximum measurement range and the transducer

will output 4 mA at zero pressure and proportionally increase to 20 mA at maximum

pressure. Proper transducer wiring is key to running the iQpump in “Auto” regulating mode.

Will the iQpump Run Without a Transducer?

The drive will display Feedback Loss (iQpump1000) or Fdb-L (iQpumpMicro) with a

blinking “ALM” indicator as shown in Figure 1, if the drive is powered up without a

transducer connected. This is normal operation until transducer wiring to the A2 terminal is

complete.

echnical

roduct(s):

TN.iQp.03

Revisio

gure 1: iQ

pump Mic

Run in

The iQp

HAND

the pum

How to

Follow t

Loss.

1. Verif

2-wi

iQpu

FE c

ip: How t

iQpump

2015 - Yaskawa

ump1000

AND Mo

mp will op

ode is use

p with a da

Fix Fdb-L

ese steps

the trans

e or 3-wire

mp1000 m

nnections

Connect

000 and i

America, Inc.

and iQpu

rate in HA

ul for settin

aged tran

or Feedb

o isolate th

ucer conn

according t

dels. Not

can be ign

and Trou

pump Mi

p Micro F

ND mode a

g up the sy

ducer.

ck Loss

e wiring iss

ctions are

o Figure 2

ll transduc

red.

leshoot T

ro Drives

ly 8, 2015

edback L

iQpu

t fixed spe

tem witho

ue if the iQ

roperly stri

or iQpump

r cables ar

ansducer

ss Displa

p1000

d without t

t transduc

ump indic

pped of ins

Micro mod

shielded,

Feedbac

c. No. TN

ansducer f

r feedback

tes Fdb-L

ulation and

ls, and Fig

in which c

iQp.03

Page

edback.

or operati

or Feedba

connected

ure 3 for

se the E(G

)

of 5

for

)

Technical Tip: How to Connect and Troubleshoot Transducer Feedback

Product(s): iQpump1000 and iQpump Micro Drives Doc. No. TN.iQp.03

Revision 1 July 8, 2015 Page 3 of 5

Figure 2: iQpump Micro 2 and 3-Wire Transducer Connections

Figure 3: iQpump1000 2 and 3-Wire Transducer Connections

Technical Tip: How to Connect and Troubleshoot Transducer Feedback

Product(s): iQpump1000 and iQpump Micro Drives Doc. No. TN.iQp.03

Revision 1 July 8, 2015 Page 4 of 5

External power supply and multi-drive wiring diagrams can be found in section 3.8 of the

iQpump1000 Quick Start Guide for alternate wiring topologies.

Note: Steps 2~5 are factory set by default for a 4-20 mA transducer wired to terminal A2

2. Voltage/Current Selection: Verify the proper setting of switches and jumpers on each

drive:

a. iQpump Micro terminal board DIP Switch S1 should be in the ‘I’ position for

current feedback transducers or ‘V’ position for voltage feedback transducers

(see Figure 4).

b. iQpump1000: Jumper S1 position A2. Jumper S1-A2 should be in the ‘I’ position

for current feedback transducers or ‘V’ position for voltage feedback transducers

(see Figure 4).

Figure 4: Terminal A2 Voltage/Current Selection

iQpump Micro iQpump1000

Technical Tip: How to Connect and Troubleshoot Transducer Feedback

Product(s): iQpump1000 and iQpump Micro Drives Doc. No. TN.iQp.03

Revision 1 July 8, 2015 Page 5 of 5

3. Verify the parameter H3-09 Terminal A2 Signal Level Selection is properly set according

to the signal type. Typically 2for current feedback devices or 0for voltage feedback

devices.

No. Name Description Values

H3-09 Terminal A2 Signal

Level Selection

0: 0 to 10 V

1: -10 to 10 V

2: 4 to 20 mA

3: 0 to 20 mA

Default: 2

Range: 0 to 3

4. Verify the proper Terminal A2 Function Selection (H3-10), typically ‘B’ for PID Feedback.

If terminal A2 is not chosen as the primary transducer feedback input, H3-10 Terminal A2

Function Selection must be disabled and terminal A1 or A3 must be configured for the

appropriate settings following steps 1-4.

How to Wire Multiple Transducers or use an External Transducer Power Supply

1. External power supply and multi-drive transducer wiring diagrams can be found in:

a. iQpump1000: Section 3.8 of the iQpump1000 Quick Start Guide

TOEPYAIP1W01.

Contact Yaskawa America, Inc. technical support at 800-YASKAWA (927-5292) if you have

any other questions regarding the Transducer Feedback Loss feature.

Table of Related Parameters

No. Name Description Values

H3-09 Terminal A2 Signal

Level Selection

1: -10 to 10 V

2: 4 to 20 mA

3: 0 to 20 mA

Note: Use Jumper S1 to set input terminal A2 for a

current or voltage input signal.

Default: 2

Range: 0 to 3

H3-10 Terminal A2

Function

Selection

Sets the function of terminal A2. Default: B

Range: 0 to 32

Andere Handbücher für iQpump1000

Dieses Handbuch passt für folgende Modelle

Andere YASKAWA Gleichstromantrieb Handbücher

YASKAWA

YASKAWA FP65U T Series Bedienungsanleitung

YASKAWA

YASKAWA E7B T Series Bedienungsanleitung

YASKAWA

YASKAWA Varispeed f7 Bedienungsanleitung

YASKAWA

YASKAWA Varispeed G7 Gebrauchs- und Pflegehandbuch

YASKAWA

YASKAWA GA800 Series Bedienungsanleitung

YASKAWA

YASKAWA PROFIBUS-DP SI-P3 Bedienungsanleitung

YASKAWA

YASKAWA iQpump1000 Bedienungsanleitung

YASKAWA

YASKAWA GA500 series Betriebsanleitung

YASKAWA

YASKAWA LA500 Betriebsanleitung

YASKAWA

YASKAWA CIMR-E7 series Bedienungsanleitung

YASKAWA

YASKAWA VS-616PS5 Series Gebrauchsanweisung

YASKAWA

YASKAWA MECHATROLINK-II Bedienungsanleitung

YASKAWA

YASKAWA L1000A CIMR-LC F Series Montage- und Bedienungsanleitung

YASKAWA

YASKAWA CIPR-GA50UB001AJ Series Bedienungsanleitung

YASKAWA

YASKAWA GA800 Series Betriebsanleitung

YASKAWA

YASKAWA GA800 Series Bedienungsanleitung

YASKAWA

YASKAWA SI-C3/V Bedienungsanleitung

YASKAWA

YASKAWA SI-N3/V Bedienungsanleitung

YASKAWA

YASKAWA L1000V CIMR-LC V Series Bedienungsanleitung

YASKAWA

YASKAWA CIMR-E7U Series Bedienungsanleitung

YASKAWA

YASKAWA Varispeed G7 Bedienungsanleitung

YASKAWA

YASKAWA SI-EP3 Bedienungsanleitung

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

YASKAWA

YASKAWA JOHB-SMP3 Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

Beckhoff

Beckhoff AX8911 Bedienerhandbuch