YASKAWA PROFINET V1000 Bedienungs- und Wartungshandbuch

Document Revision: v1.0.5 of

1 10

page

18805 Adams Ct., #110 ~ Morgan Hill, CA 95037, USA ~ +1-408.924.0808 ~ www.washlinksystems.com ~ [email protected]

Tech Guide

Yaskawa

V1000

Basic User Guide

Document Revision: v1.0.5 of

2 10

page

18805 Adams Ct., #110 ~ Morgan Hill, CA 95037, USA ~ +1-408.924.0808 ~ www.washlinksystems.com ~ [email protected]

Document Title: Tech Guide ~ Yaskawa V1000 Basic User Guide

WASHLINK SYSTEMS

Yaskawa V1000 Basic User Guide

This document provides basic information for navigating and adjusting your Washlink Systems

supplied Yaskawa V1000 Variable Frequency Drive.

When emailing or calling for assistance, you must have the following information available:

Location Name: ______________________________

Contact Person: ______________________________

Contact Phone: ______________________________

VFD Model: ______________________________

Equipment connected: ______________________________

Distributor Name: ______________________________

THIS DOCUMENT IS THE EXCLUSIVE PROPERTY OF WASHLINK SYSTEMS AND IS PREPARED

ONLY FOR USE BY THE COMPANY PURCHASINGTHE EQUIPMENT. EDITING, COPYING,

DISTRIBUTING, AND/OR SELLING THIS DOCUMENT IS STRICTLY PROHIBITED WITHOUT PRIOR

WRITTEN CONSENT FROM WASHLINK SYSTEMS. WASHLINK SYSTEMS RESERVES THE RIGHT

TO EDIT THIS DOCUMENT IN ANY MANNER DEEMED NECESSARY, AT ANY TIME, AND WITHOUT

PRIOR NOTICE.

Document Revision: v1.0.5 of

3 10

page

18805 Adams Ct., #110 ~ Morgan Hill, CA 95037, USA ~ +1-408.924.0808 ~ www.washlinksystems.com ~ [email protected]

Document Title: Tech Guide ~ Yaskawa V1000 Basic User Guide

Output Frequency (Hz)

Output Current (Amps)

Output Voltage

Monitor Display (typically not used)

Verify Menu (typically not used)

Set Up Mode (typically not used)

Parameter Setting mode

Auto-Tuning

Hz drive set to run

Forward Selection/Reverse Selection (typically not used)

Standard Operator Panel

Display

To Change Display Data View

The standard screen after a power cycle is the actual output in Hz (xx.xx)

To change data being displayed, press the or to the desired view.

Document Revision: v1.0.5 of

4 10

page

18805 Adams Ct., #110 ~ Morgan Hill, CA 95037, USA ~ +1-408.924.0808 ~ www.washlinksystems.com ~ [email protected]

Document Title: Tech Guide ~ Yaskawa V1000 Basic User Guide

Standard Operator Panel

Display

To Access & Change Paramaters

Press the or button until the screen showes Parameter Setting mode.

Press the button, display will now show Parameter A1-02 with the “A” flashing

ENTER

Press the or or to get to the parameter you want to adjust, then press

ENTER

RESET

You will now see the current setting for the selected parameter, left digit will flashing

Press the or or to change the parameter, then press

ENTER

RESET

With the VFD powered on and the motor not running;

You will now see the next parameter with the left digit flashing

If you want to adjust more parameters, go to step 3.7.

If you are done, press until you get back to the screen8. ESC

Press the or button until the screen shows (motor speed in Hz).

Document Revision: v1.0.5 of

5 10

page

18805 Adams Ct., #110 ~ Morgan Hill, CA 95037, USA ~ +1-408.924.0808 ~ www.washlinksystems.com ~ [email protected]

Document Title: Tech Guide ~ Yaskawa V1000 Basic User Guide

Common Drive Settings

b1-03 Stopping Method

0=Ramp Down, 1=Coast to Stop

b3-01 Speed Search Selection at Start (Flying Start)

0=Disabled, 1=Enabled

b5-03 PID Input Time Debounce (in seconds)

If used typically between 1.0-3.0

(note if more then one motor on same sensor, times must be different to prevent drive speed bouncing)

C1-01 Acceleration time 1 (in seconds)

Typically between 3.0-15.0

C1-02 Deceleration time 1 (in seconds)

Typically between 3.0-25.0

d1-01 Frequency Reference 1 (speed in Hz)

Typically between 35.0-60.0

d1-02 Frequency Reference 2 (speed in Hz)

Typically between 35.0-60.0

o1-02 Monitor selection after power up (what the display shows)

3=Output Frequency (what speed the motor is running in Hz.)

4=Output Current (how many amps the motor is using when running)

Document Revision: v1.0.5 of

6 10

page

18805 Adams Ct., #110 ~ Morgan Hill, CA 95037, USA ~ +1-408.924.0808 ~ www.washlinksystems.com ~ [email protected]

Document Title: Tech Guide ~ Yaskawa V1000 Basic User Guide

Common Drive Monitors

Note: these are basic tips, refer to the technical manual for more information

U1-01 Frequency Reference Monitors the frequency

U1-02 Output Frequency Displays the output frequency. Display units are determined by o1-03.

U1-03 Output Current Displays the output current.

U1-04 Control Mode Control method set in A1-02.

U1-05 Motor Speed Displays the motor speed feedback. Display units are determined by o1-03.

U1-06 Output Voltage Reference Displays the output voltage.

U1-07 DC Bus Voltage Displays the DC bus voltage.

U1-08 Output Power Displays the output voltage (this value is determined internally).

U1-13 Terminal A1 Input Level Displays analog input A1 level: 100% when input is 10 V.

U1-14 Terminal A2 Input Level Displays analog input A1 level: 100% when input is 10 V.

U3-01 Most Recent Fault Displays the most recent fault.

U3-02 2nd Most Recent Fault Displays the second most recent fault.

U3-03 3rd Most Recent Fault Displays the third most recent fault.

U3-04 4th Most Recent Fault Displays the fourth most recent fault.

U3-05 5th Most Recent Fault Displays the fifth most recent fault.

U3-06 6th Most Recent Fault Displays the sixth most recent fault.

U3-07 7th Most Recent Fault Displays the seventh most recent fault.

U3-08 8th Most Recent Fault Displays the eighth most recent fault.

U3-09 9th Most Recent Fault Displays the ninth most recent fault.

U3-10 10th Most Recent Fault Displays the tenth most recent fault.

U4-01 Accumulated Operation Time Displays the cumulative operation time of the drive.

U4-02 Number of Run Commands Displays the number of times the run command is entered.

Document Revision: v1.0.5 of

7 10

page

18805 Adams Ct., #110 ~ Morgan Hill, CA 95037, USA ~ +1-408.924.0808 ~ www.washlinksystems.com ~ [email protected]

Document Title: Tech Guide ~ Yaskawa V1000 Basic User Guide

Common Drive Faults

Note: these are basic tips, refer to the technical manual for more information

Output Power Phase Loss

The output cable is disconnected.

• Check for wiring errors and ensure the output cable is connected properly.

• Correct the wiring.

The motor winding is damaged.

• Check the resistance between motor lines.

• Replace the motor if the winding is damaged.

The output terminal is loose.

• Apply the tightening torque specified in this manual to fasten the terminals.

An output transistor is damaged.

• Replace the drive.

Ground Fault

Motor insulation is damaged.

• Check the insulation resistance of the motor.

• Replace the motor.

Hardware problem.

• Replace the drive.

Over Current

The motor has been damaged due to overheating or the motor insulation is damaged.

• Check the insulation resistance.

• Replace the motor.

One of the motor cables has shorted out or there is a grounding problem.

• Check the motor cables.

• Check the resistance between the motor cables and the ground terminal .

• Replace damaged cables.

The load is too heavy.

• Reduce the load to avoid sudden changes in the current level or switch to a larger drive.

The acceleration or deceleration times are too short.

• Increase the acceleration time

• Increase the deceleration time

Motor Overload

Load is too heavy.

• Reduce the load.

Cycle times are too short during acceleration and deceleration.

• Increase the acceleration and deceleration times (C1-01 through C1-08).

Multiple motors are running off the same drive.

• Disable the Motor Protection function (L1-01 = “0”) and install a thermal relay to each motor.

Output current fluctuation due to input phase loss

• Check the power supply for phase loss

Drive Overload

Load is too heavy.

• Reduce the load.

Cycle times are too short during acceleration and deceleration.

• Increase the acceleration and deceleration times (C1-01 through C1-08).

Output current fluctuation due to input phase loss

• Check the power supply for phase loss.

Document Revision: v1.0.5 of

8 10

page

18805 Adams Ct., #110 ~ Morgan Hill, CA 95037, USA ~ +1-408.924.0808 ~ www.washlinksystems.com ~ [email protected]

Document Title: Tech Guide ~ Yaskawa V1000 Basic User Guide

DC Bus Under Voltage

Input power phase loss.

• The main circuit drive input power is wired incorrectly.

One of the drive input power wiring terminals is loose.

• Ensure there are no loose terminals.

There is a problem with the voltage from the drive input power.

• Check the voltage.

The power has been interrupted.

• Correct the drive input power.

Drive internal circuitry has become worn.

• Check the maintenance time for the capacitors (U4-05).

• Replace the drive if U4-05 exceeds 90%.

Input Power Phase Loss

There is phase loss in the drive input power.

• Check for wiring errors in the main circuit drive input power.

There is loose wiring in the drive input power terminals.

• Ensure the terminals are tightened properly.

There is excessive fluctuation in the drive input voltage.

• Check the voltage from the drive input power.

There is poor balance between voltage phases.

• Stabilize drive input power or disable phase loss detection.

Over Voltage

Deceleration time is too short and regenerative energy flows from the motor into the drive.

• Increase the deceleration time (C1-02, -04, -06, -08).

Drive input power voltage is too high.

• Check the voltage.

Surge voltage entering from the drive input power.

• Install a DC reactor.

Ground fault in the output circuit causing the DC bus capacitor to overcharge.

• Check the motor wiring for ground faults.

The dynamic braking transistor is damaged.

• Replace the drive.

Common Drive Faults

Note: these are basic tips, refer to the technical manual for more information

Document Revision: v1.0.5 of

9 10

page

18805 Adams Ct., #110 ~ Morgan Hill, CA 95037, USA ~ +1-408.924.0808 ~ www.washlinksystems.com ~ [email protected]

Document Title: Tech Guide ~ Yaskawa V1000 Basic User Guide

Revision history

v1.0.1 Initial release

v1.0.3 Various typo’s

v1.0.5 Fixed red display box images

Document Revision: v1.0.5 of

10 10

page

18805 Adams Ct., #110 ~ Morgan Hill, CA 95037, USA ~ +1-408.924.0808 ~ www.washlinksystems.com ~ [email protected]

Document Title: Tech Guide ~ Yaskawa V1000 Basic User Guide

Notes:

Andere Handbücher für PROFINET V1000

Inhaltsverzeichnis

Andere YASKAWA Gleichstromantrieb Handbücher

YASKAWA

YASKAWA GA800 Series Bedienungsanleitung

YASKAWA

YASKAWA E7B T Series Bedienungsanleitung

YASKAWA

YASKAWA 1000 Series Bedienungsanleitung

YASKAWA

YASKAWA GA80U4720ABM Bedienungsanleitung

YASKAWA

YASKAWA HV600 Bedienungsanleitung

YASKAWA

YASKAWA iQpump Micro Bedienungsanleitung

YASKAWA

YASKAWA E7 Drive Bedienungsanleitung

YASKAWA

YASKAWA FP65U T Series Bedienungsanleitung

YASKAWA

YASKAWA PROFINET V1000 Bedienungsanleitung

YASKAWA

YASKAWA LA500 Betriebsanleitung

YASKAWA

YASKAWA MECHATROLINK-III Bedienungsanleitung

YASKAWA

YASKAWA SI-N3/V Bedienungsanleitung

YASKAWA

YASKAWA JOHB-SMP3-MA Bedienungsanleitung

YASKAWA

YASKAWA SI-P1/ V7 Bedienungsanleitung

YASKAWA

YASKAWA HV600 Gebrauchs- und Pflegehandbuch

YASKAWA

YASKAWA CM093 Bedienungsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

YASKAWA

YASKAWA DeviceNet SI-N3 Bedienungsanleitung

YASKAWA

YASKAWA VS-616PS5 Series Betriebsanleitung

YASKAWA

YASKAWA Varispeed f7 Bedienungsanleitung

YASKAWA

YASKAWA CDBR Series Bedienungsanleitung

YASKAWA

YASKAWA SI-EN3D Bedienungsanleitung

YASKAWA

YASKAWA JVOP-181 Montageanleitung

YASKAWA

YASKAWA V1000 SI-S3/V Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

Beckhoff

Beckhoff AX8911 Bedienerhandbuch