YASKAWA MOTOMAN-MS165 Bedienungsanleitung
MANUAL NO.
HW1482308
Part Number: 167109-1CD
Revision: 5
10
MOTOMAN-MS165
INSTRUCTIONS
TYPE:
YR-MS165/MH180-A00 (STANDARD SPECIFICATION)
Upon receipt of the product and prior to initial operation, read these instructions thoroughly, and
retain for future reference.
MOTOMAN INSTRUCTIONS
MOTOMAN-MS165 INSTRUCTIONS
DX200 INSTRUCTIONS
DX200 OPERATOR’S MANUAL (for each purpose)
The DX200 operator’s manual above corresponds to specific usage. Be sure to use the appropriate manual.
1 of 100
ii
167109-1CD
HW1482308
MS165
Copyright © 2018, 2017, 2016, 2015 Yaskawa America, Inc.
Terms of Use and Copyright Notice
All rights reserved. This manual is freely available as a service to
Yaskawa customers to assist in the operation of Motoman robots, related
equipment and software This manual is copyrighted property of Yaskawa
and may not be sold or redistributed in any way. You are welcome to copy
this document to your computer or mobile device for easy access but you
may not copy the PDF files to another website, blog, cloud storage site or
any other means of storing or distributing online content.
Printed in the United States of America
First Printing, 2018
Yaskawa America, Inc.
Motoman Robotics Division
100 Automation Way
Miamisburg, OH 45342
Phone: 937-847-6200
www.motoman.com
2 of 100
iii
167109-1CD
HW1482308
MS165
• This instruction manual is intended to explain mainly on the
mechanical part of the MOTOMAN-MS165 for the application to the
actual operation and for proper maintenance and inspection. It
describes on safety and handling, details on specifications,
necessary items on maintenance and inspection, to explain
operating instructions and maintenance procedures. Be sure to
read and understand this instruction manual thoroughly before
installing and operating the manipulator.
• General items related to safety are listed in Chapter 1: Safety of the
DX200 Instructions. To ensure correct and safe operation, carefully
read the DX200 Instructions before reading this manual.
• Some drawings in this manual are shown with the protective covers
or shields removed for clarity. Be sure all covers and shields are
replaced before operating this product.
• The drawings and photos in this manual are representative
examples and differences may exist between them and the
delivered product.
• YASKAWA may modify this model without notice when necessary
due to product improvements, modifications, or changes in
specifications.
If such modification is made, the manual number will also be
revised.
• If your copy of the manual is damaged or lost, contact a YASKAWA
representative to order a new copy. The representatives are listed
on the back cover. Be sure to tell the representative the manual
number listed on the front cover.
• YASKAWA is not responsible for incidents arising from
unauthorized modification of its products. Unauthorized
modification voids your product's warranty.
3 of 100
iv
167109-1CD
HW1482308
MS165
We suggest that you obtain and review a copy of the ANSI/RIA National
Safety Standard for Industrial Robots and Robot Systems (ANSI/RIA
R15.06-2012). You can obtain this document from the Robotic Industries
Association (RIA) at the following address:
Robotic Industries Association
900 Victors Way
P.O. Box 3724
Ann Arbor, Michigan 48106
TEL: (734) 994-6088
FAX: (734) 994-3338
www.roboticsonline.com
Ultimately, well-trained personnel are the best safeguard against
accidents and damage that can result from improper operation of the
equipment. The customer is responsible for providing adequately trained
personnel to operate, program, and maintain the equipment. NEVER
ALLOW UNTRAINED PERSONNEL TO OPERATE, PROGRAM, OR
REPAIR THE EQUIPMENT!
We recommend approved Yaskawa training courses for all personnel
involved with the operation, programming, or repair of the equipment.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
4 of 100
v
167109-1CD
HW1482308
MS165
Notes for Safe Operation
Read this manual carefully before installation, operation, maintenance, or
inspection of the MOTOMAN-MS165.
In this manual, the Notes for Safe Operation are classified as “DANGER”,
“WARNING”, “CAUTION”, “MANDATORY”, or “PROHIBITED”.
Even items described as “CAUTION” may result in a serious accident in
some situations.
At any rate, be sure to follow these important items.
DANGER
Indicates an imminent hazardous
situation which, if not avoided, could
result in death or serious injury to
personnel.
WARNING
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury to
personnel.
Indicates a potentially hazardous
situation which, if not avoided, could
result in minor or moderate injury to
personnel and damage to
equipment. It may also be used to
alert against unsafe practices.
Always be sure to follow explicitly
the items listed under this heading.
Must never be performed.
To ensure safe and efficient operation at all times, be sure
to follow all instructions, even if not designated as
“DANGER”, “WARNING” and “CAUTION” .
DANGER
• Maintenance and inspection must be performed by specified
personnel.
Failure to observe this caution may result in electric shock or injury.
• For disassembly or repair, contact your YASKAWA representative.
• Do not remove the motor, and do not release the brake.
Failure to observe these safety precautions may result in death or
serious injury from unexpected turning of the manipulator's arm.
5 of 100
vi
167109-1CD
HW1482308
MS165
WARNING
• Before operating the manipulator, check that servo power is turned
OFF pressing the emergency stop buttons on the front door of the
DX200 and the programming pendant.
When the servo power is turned OFF, the SERVO ON LED on the
programming pendant is turned OFF.
Injury or damage to machinery may result if the emergency stop circuit
cannot stop the manipulator during an emergency. The manipulator
should not be used if the emergency stop buttons do not function.
Fig. : Emergency Stop Button
• Once the emergency stop button is released, clear the cell of all
items which could interfere with the operation of the manipulator.
Then turn the servo power ON.
Injury may result from unintentional or unexpected manipulator motion.
Fig. : Release of Emergency Stop
• Observe the following precautions when performing teaching
operations within the P-point maximum envelope of the
manipulator:
– Be sure to use a lockout device to the safeguarding when going
inside. Also, display the sign that the operation is being
performed inside the safeguarding and make sure no one closes
the safeguarding.
– View the manipulator from the front whenever possible.
– Always follow the predetermined operating procedure.
– Keep in mind the emergency response measures against the
manipulator’s unexpected motion toward you.
– Ensure that you have a safe place to retreat in case of
emergency.
Improper or unintended manipulator operation may result in injury.
• Confirm that no person is present in the P-point maximum envelope
of the manipulator and that you are in a safe location before:
– Turning ON the power for the DX200.
– Moving the manipulator with the programming pendant.
– Running the system in the check mode.
– Performing automatic operations.
Injury may result if anyone enters the P-point maximum envelope of the
manipulator during operation. Always press an emergency stop button
immediately if there is a problem.
6 of 100
vii
167109-1CD
HW1482308
MS165
Definition of Terms Used Often in This Manual
The MOTOMAN is the YASKAWA industrial robot product.
The MOTOMAN usually consists of the manipulator, the controller, the
programming pendant, and supply cables.
In this manual, the equipment is designated as follows:
Description of the Operation Procedure
In the explanation of the operation procedure, the expression “Select • • •”
means that the cursor is moved to the object item and the SELECT key is
pressed, or that the item is directly selected by touching the screen.
Registered Trademark
In this manual, names of companies, corporations, or products are
trademarks, registered trademarks, or brand names for each company or
corporation. The indications of (R) and TM are omitted.
• Perform the following inspection procedures prior to conducting
manipulator teaching. If problems are found, repair them
immediately, and be sure that all other necessary processing has
been performed.
– Check for problems in manipulator movement.
– Check for damage to insulation and sheathing of external wires.
• Always return the programming pendant to the hook on the cabinet
of the DX200 after use.
The programming pendant can be damaged if it is left in the
manipulator's work area, on the floor, or near fixtures.
• Read and understand the Explanation of Warning Labels in the
DX200 Instructions before operating the manipulator.
Equipment Manual Designation
DX200 controller DX200
DX200 programming pendant Programming pendant
Cable between the manipulator and the
controller
Manipulator cable
7 of 100
viii
167109-1CD
HW1482308
MS165
Explanation of Warning Labels
The following warning labels are attached to the manipulator.
Always follow the warnings on the labels.
Also, an identification label with important information is placed on the
body of the manipulator. Prior to operating the manipulator, confirm the
contents.
Note: Taking the maintenance-relevant trainings offered by YASKAWA is
indispensable for replacing the L-axis of the balancer-equipped
manipulator.
Fig. : Warning Label Locations
WARNING Label B
WARNING Label A
WARNING Label B
WARNING Label C
Nameplate
(On the manipulator
manufactured by May 2014)
Nameplate
(On the manipulator manufactured after June 2014)
WARNING Label C
WARNING
Do not enter
robot
work area.
WARNING
Moving parts
may cause
injury
Nameplate:
WARNING Label B:
WARNING Label A:
release the brake. Failure to observe
Do not remove the motor,and do not
this caution may result in injury from
unexpected turning of the manipulator arm.
Please contact your Yaskawa representive.
DANGER
WARNING Label C:
MADEINJAPAN
YASKAWAELECTRICCORPORATION
Kitakyushu806-0004Japan
2-1Kurosakishiroishi,Yahatanishi-ku,
SERIALNO.
PAYLOAD kg
TYPE
MASS
DATE
ORDERNO.
kg
MOTOMAN-
MODEL
NJ3878
8 of 100
ix
167109-1CD
HW1482308
MS165
Safeguarding Tips
All operators, programmers, maintenance personnel, supervisors, and
anyone working near the system must become familiar with the operation
of this equipment. All personnel involved with the operation of the
equipment must understand potential dangers of operation. General
safeguarding tips are as follows:
• Improper operation can result in personal injury and/or damage to
the equipment. Only trained personnel familiar with the operation of
this equipment, the operator's manuals, the system equipment, and
options and accessories should be permitted to operate this
equipment.
• Improper connections can damage the equipment. All connections
must be made within the standard voltage and current ratings of the
equipment.
• The system must be placed in Emergency Stop (E-Stop) mode
whenever it is not in use.
• In accordance with ANSI/RIA R15.06-2012, section 4.2.5, Sources of
Energy, use lockout/tagout procedures during equipment
maintenance. Refer also to Section 1910.147 (29CFR, Part 1910),
Occupational Safety and Health Standards for General Industry
(OSHA).
Mechanical Safety Devices
The safe operation of this equipment is ultimately the users responsibility.
The conditions under which the equipment will be operated safely should
be reviewed by the user. The user must be aware of the various national
codes, ANSI/RIA R15.06-2012 safety standards, and other local codes
that may pertain to the installation and use of this equipment.
Additional safety measures for personnel and equipment may be required
depending on system installation, operation, and/or location. The following
safety equipment is provided as standard:
• Safety barriers
• Door interlocks
• Emergency stop palm buttons located on operator station
Check all safety equipment frequently for proper operation. Repair or
replace any non-functioning safety equipment immediately.
9 of 100
x
167109-1CD
HW1482308
MS165
Programming, Operation, and Maintenance Safety
All operators, programmers, maintenance personnel, supervisors, and
anyone working near the system must become familiar with the operation
of this equipment. Improper operation can result in personal injury and/or
damage to the equipment. Only trained personnel familiar with the
operation, manuals, electrical design, and equipment interconnections of
this equipment should be permitted to program, or maintain the system.
All personnel involved with the operation of the equipment must
understand potential dangers of operation.
• Inspect the equipment to be sure no potentially hazardous conditions
exist. Be sure the area is clean and free of water, oil, debris, etc.
• Be sure that all safeguards are in place. Check all safety equipment
for proper operation. Repair or replace any non-functioning safety
equipment immediately.
• Check the E-Stop button on the operator station for proper operation
before programming. The equipment must be placed in Emergency
Stop (E-Stop) mode whenever it is not in use.
• Back up all programs and jobs onto suitable media before program
changes are made. To avoid loss of information, programs, or jobs, a
backup must always be made before any service procedures are
done and before any changes are made to options, accessories, or
equipment.
• Any modifications to the controller unit can cause severe personal
injury or death, as well as damage to the robot! Do not make any
modifications to the controller unit. Making any changes without the
written permission from Yaskawa will void the warranty.
• Some operations require a standard passwords and some require
special passwords.
• The equipment allows modifications of the software for maximum
performance. Care must be taken when making these modifications.
All modifications made to the software will change the way the
equipment operates and can cause severe personal injury or death,
as well as damage parts of the system. Double check all
modifications under every mode of operation to ensure that the
changes have not created hazards or dangerous situations.
• This equipment has multiple sources of electrical supply. Electrical
interconnections are made between the controller and other
equipment. Disconnect and lockout/tagout all electrical circuits
before making any modifications or connections.
• Do not perform any maintenance procedures before reading and
understanding the proper procedures in the appropriate manual.
• Use proper replacement parts.
• Improper connections can damage the equipment. All connections
must be made within the standard voltage and current ratings of the
equipment.
10 of 100
Inhaltsverzeichnis
Andere YASKAWA Robotik Handbücher
YASKAWA
YASKAWA MOTOMAN MPL80 II Bedienungsanleitung
YASKAWA
YASKAWA MOTOMAN DX100 Bedienungsanleitung
YASKAWA
YASKAWA Motoman GP8 EduCart Benutzerhandbuch
YASKAWA
YASKAWA MOTOMAN-VA1400 Bedienungsanleitung
YASKAWA
YASKAWA Motoman GP50 Bedienungsanleitung
YASKAWA
YASKAWA MOTOMAN-MH50 Bedienungsanleitung
YASKAWA
YASKAWA MOTOMAN-MA1900 Bedienungsanleitung
YASKAWA
YASKAWA Motoman DX200 Bedienungsanleitung
YASKAWA
YASKAWA Motoman DX200 Bedienungsanleitung
YASKAWA
YASKAWA MOTOMAN-SDA Bedienungsanleitung
YASKAWA
YASKAWA Motoman ArcWorld IV-6300 XHD TR3C Benutzerhandbuch
YASKAWA
YASKAWA MOTOMAN-MPX2600 Bedienungsanleitung
YASKAWA
YASKAWA MOTOMAN MYS450L Handbuch
YASKAWA
YASKAWA Motoman XRC Stücklistenhandbuch
YASKAWA
YASKAWA YYR-1-06VXH25-A10 Betriebsanleitung
YASKAWA
YASKAWA Smart Series Montage- und Bedienungsanleitung
YASKAWA
YASKAWA MOTOMAN-EPX1750 Bedienungsanleitung
YASKAWA
YASKAWA motoman NX100 Kurzanleitung
YASKAWA
YASKAWA MPL160-J00 Betriebsanleitung
YASKAWA
YASKAWA YRC1000micro Benutzerhandbuch
Beliebte Robotik Handbücher anderer Marken
WowWee
WowWee ROBOQUAD Bedienungsanleitung
Milvus Robotics
Milvus Robotics SEIT 100 Bedienungsanleitung
RoboMaster
RoboMaster AI Robot 2020 Standard Version Bedienungsanleitung
fischertechnik
fischertechnik Mini Bots Bedienungsanleitung
Abicor Binzel
Abicor Binzel iCAT mini Bedienungsanleitung
ABB
ABB OmniCore E10 Bedienungsanleitung
