Please read this user’s manual thoroughly to ensure correct use of the
instrument. Carefully store this manual for future reference.
1. Cautionary Notes for Safe Use of the Products
The following symbol is indicated on the instrument and in this manual to
ensure safe use.
This symbol is indicated where theoperator must refer to instructions
in the manual in order to protect both personnel and the instrument.
This symbol on the product indicates that the operator must refer to
an explanation in the user’s manual inorder to avoid the risk of injury
or death of personnel and damage to the instrument. The manual
describes how the operator should exercise special care to avoid
electric shock or other dangers that may in injury or loss of life.
The purpose of the following conventional symbol in this manual is:
NOTE
Draws attention to information essential for understanding the
operation and features.
2.
Handling Precautions and Installation Location
N
OTE
●Note that these current transformers are designed for use with
general-purpose instruments and have not yet gained any official
certification. They cannot therefore be used for the purpose of
ascertaining wattage or other electric parameters.
●Use each current transformers under a load no greater than its
rated level. When calculating the load, you must calculate the
sum of the load given by the instruments to be connected to the
transformer and the load given by the lead-wire of the
secondary-stage cable.
●The inner-walls of the clamp are treated with rust preventive. But
if rusted, remove the rust with CRC-5-56 (goods on the market)
and spray rust preventive on the inner-walls again for recovery.
Avoid installing the current transformers in locations subject to:
ambient temperatures outside thespecified range of -20 °C to 50 °C, where
condensation is likely; ambient humidity exceeding 80 % RH, where
condensation is likely; relatively large amounts of flammable or explosive
gas, saline substance, lampblack or dust; splashes of water, oil or solvent;
radioactive rays or intense electric or magnetic fields; frequent mechanical
vibration or shock; or direct sunlight.
3. Installation
W
ARNING
Since there is a risk of electric shock during installation, be sure to
observe the following.
●Before connectingthe transformer to any other equipment, make
sure the circuit is not receiving any power in order to prevent
electric shock.
●Fasten the connecting terminals securely so they will not loosen
readily.
●Do not touch the terminals or any other part of the transformer
when the circuit is live.
●Do not use the transformer under a circuit current greater than
the level specified for that model.
●Do not use the transformer under a circuit voltage greater than
500 V AC.
N
OTE
The CTW containsa device for suppressing hazardous voltages that
ay arise when the secondary line is open-circuited.m
Install the transformer referring to the following figures.
How to Install and How to Remove
Example of Installation
Cable
Power-source side
K
Load side
L
Secondary-
stage cable
l side=black
k side=white
Banding band
BA
How to Install
Push the B part until it clicks to lock
the A part.
How to Remove
Loosen the A part using a flat-blade
screw driver to unlock, and pull the B
part in the direction of the arrow to
release.
● Attach the transformer to the cable according to the orientation of the
K and L symbols, as shown in the figure.
● Be careful not to make a gap between the inner-walls of the clamp.
● Be careful not to trap any dust between the inner-walls of the clamp.
● Use a crimp-on terminal for 0.75 mm2 cables to connect the
secondary-stage cable.
● The wires of the secondary-stage cable are color-coded as follows.
k side=white; l side=black
● Fix the transformer with a banding band or the like as shown in the
figure above to prevent it from falling.
IM 77C01W03-01E
3rd Edition: Jan.2005
User’s
Manual
Cross-check the Model
Make sure the model and suffix codes shown on the data plate attached to
the transformer are the same as specified in your purchase order.
Models Names
CTW15 Clamp-on Current Transformer (for 100A/ 1 A)
Applicable cable diameter: less than
Φ
24 mm
CTW35 Clamp-on Current Transformer (for 300A/ 1 A)
Applicable cable diameter: less than
Φ
36 mm
Models CTW15 and CTW35
Clamp-on Current Transformers
IM 77C01W03-01E 3rd Edition : 2005.01.15-00
1
