YOODA SMART TOUCH 2 Bedienungsanleitung
In order to fully explore available functions of SMART TOUCH 2 system please take a moment and read this manual before using the device. SMART
TOUCH 2 system is compatible with all YOODA brand devices.
From the top:
SMART TOUCH 2 transmitter system
Seal SMART TOUCH 2 system
Finish elements of the seal for SMART TOUCH 2 system
Transition strip with touch sensor for SMART TOUCH 2 system
1. Range:
up to 35 meters
2. Battery:
1 x CR2430
3. Power supply:
3 V
4. Dimensions of the transmitter:
40 x 65 x 17 mm
6. Transmitting power:
10 mW
7. Operating temperature:
from -20°C to 50°C
8. Protection degree:
IP 55
9. Possibility to program 3 work modes:
a) stop the work motor,
b) stop the work motor and reverse one turn
c) stop and maximum motor reverse to the upper end position
Radio receiver range is a variable value and can differ from declared values depending on conditions in which device
operates. Possible sources of changes in range are building construction, interference caused by other radio transmitters
etc.
System SMART TOUCH 2
www.sukcesgroup.pl
1. General information
1
The garage door security system includes 3 working modes A,B and C. Programming the transmitter takes place after
opening the transmitter cover.
WORK MODE A - stop the work mode of the motor. After encountering an unexpected obstacle in the area of the closed
garage door or roller shutter, the system will stop automatically and immediately.
WORK MODE B - stop the work mode of the motor and reverse one turn. After encountering an unexpected obstacle in the
area of the closed garage door or roller shutter, the cover will be automatically and immediately stopped and its operation
will be reversed by one turn.
WORK MODE C - and maximum motor reverse to the upper end position. After encountering an unexpected obstacle in
the area of the closed garage door or roller shutter, the motor will automatically stop and the cover will be raised to its
upper end position.
2. Detailed description
3. Installation
4. Choosing work mode
2
Clamps connecting seal with the transmitter
UP button
Work mode switch
Battery
Programming button
The seal should be placed
directly in the bottom of the
roller slat or the transition strip.
Turn on one of the 3 working
modes - A, B or C or turn off the
device using the switch.
The transmitter's
power is off.
Put finish elements
on the ends of the seal.
The finish element
of the seal connect
to the transmitter.
LImiter of the transmitter should
be placed with the door closed in
a position parallel to the transmitter
at a distance T (T <25 mm).
The transmitter's
power is on.
A work mode. B work mode. C work mode.
5. Adding transmitter to R type motors
6. Adding transmitter to R type motors using the key-ring remote control
3
Longer than 5 seconds pause between series of button clicks during programming will cause device to switch off from
programming mode without saving any changes.
Motor will make a sound.
Roller shutter will make
an up/down move.
Motor will
make a sound.
Roller shutter
will make
an up/down move
and the motor
will make a few
short sounds.
Press
programming button
P2 on the A
remote control.
Press
programming button
P2 on the A
remote control.
Press
programming button
P2 on the B transmitter.
Motor will make a sound.
Roller shutter will make
an up/down move.
Motor will
make a sound.
Roller shutter
will make
an up/down move
and the motor
will make a few
short sounds.
Press
simultaneously
STOP and UP buttons.
Press
simultaneously
STOP and UP buttons.
Press
programming button
P2 on the B transmitter.
Transmitter
has been
programmed.
Transmitter
has been
programmed.
1. Simultaneously pressing the STOP and UP buttons performs the function of programming button.
2. Longer than 5 seconds pause between series of button clicks during programming will cause device to switch off from
programming mode without saving any changes.
Andere YOODA Fernbedienung Handbücher
YOODA
YOODA MELODY 1R Bedienungsanleitung
YOODA
YOODA MAGNETIC Deluxe Series Bedienungsanleitung
YOODA
YOODA MAGNETIC PRO 1RT YSH Bedienungsanleitung
YOODA
YOODA NUXO Series Bedienungsanleitung
YOODA
YOODA SVERO Series Bedienungsanleitung
YOODA
YOODA VITO Series Bedienungsanleitung
YOODA
YOODA ARTISTIC 1R Bedienungsanleitung
YOODA
YOODA UNO Series Bedienungsanleitung
YOODA
YOODA ARTISTIC 5R Bedienungsanleitung
YOODA
YOODA VETRO 5RT Bedienungsanleitung
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
