Yunca Heating MONTE Bedienungsanleitung

Monte Multi & Monte Euro Multi Installation - AUG_2014.doc www.yunca.co.nz Page 1 of 4

A division of Terry Young Ltd, New Zealand

INSTALLATION INSTRUCTIONS for

MONTE MULTI-FUEL & MONTE EURO MULTI-FUEL

FREESTANDING BURNER

REFER TO APPLIED RESEARCH TEST REPORT 12/2514 APRIL 2012

TESTED in compliance with the requirements of AS/NZS 2918:2001

The Yunca Monte Multi-Fuel and Monte Euro Multi-Fuel are NOT clean-air approved.

A. Yunca recommends that competent trades persons carry out all installations (e.g. NZHHA

Registered Installer), to obtain maximum performance and safe, efficient heating.

B. A permit is required and we suggest you check with local building inspectors as by-laws

do vary from area to area.

Also notify your Insurance Company that a solid fuel heater has been installed.

C. Ash Floor Protector –

1. Must extend a minimum of 300mm in front of the door aperture.

2. Must extend at least 125mm from each side of the heater.

3. Ash Floor Protector must be constructed of non-combustible materials.

D. Seismic restraint –Heater must be restrained from seismic movement as required by

AS/NZS 2918:2001. 10mm diameter bolting holes in the rear corners allow restraint.

E. Manufacturers recommended tested minimum clearances from combustible walls:

Tested to NZS by APPLIED RESEARCH SERVICES

Clearance

Rear Clearance (with YUNCA flue guard fitted)

150mm

Side Clearance (with YUNCA flue guard fitted)

400mm

Corner Clearance (with YUNCA flue guard fitted)

200mm

F. YUNCA Flue Kit (Complies to AS/NZS 2918:2001 Appendix F): FIG A, B & E

1. 4.2m x 150mm stainless steel flue. 4. 1 x insulation boundary shield.

2. 2.4m x 250mm galvanised liner. 5. 2 x spider brackets.

3. 1 x ceiling tile. 6. 1 x weather cap & cowl.

7. 4 x support angles

Please Note: All joints must be sealed with flue sealing compound. Use stainless steel

screws or rivets to join the flue pipe (three equally spaced places at each joint). The first

length of flue must be fixed to the flue spigot with at least one stainless steel screw or rivet.

The required minimum flue termination height is 4.6 m above the floor protector.

G. MULTI-FUEL & EURO MULTI-FUEL Flue Mounted Shield (Flue Guard) Kit: FIG A

Complies (with heater) to AS/NZS 2918:2001

1 x 1200mm length lined Back Guard.

1 x 1200mm length Perforated Front Guard.

1 x 1200mm length Tertiary Back Guard with spacers.

1 x top front deflector shield (half round shaped, angled when installed).

Please Note: The minimum Flue Guard Height is 1200mm.

Monte Multi & Monte Euro Multi Installation - AUG_2014.doc www.yunca.co.nz Page 2 of 4

MONTE MULTI-FUEL & MONTE EURO MULTI-FUEL –TYPICAL FLUE INSTALLATION

(drawings on the following pages not drawn to scale)

FIG A MONTE MULTI-FUEL & MONTE EURO MULTI-FUEL Flue Mounted Shield

(Flue Guard) Kit Installation

Complies (with heater) to AS/NZS 2918:2001

CEILING PLATE

25mm min. BETWEEN LINER & ANY TIMBER

ENLARGEMENT OF CEILING ASSEMBLY

300

300mm Sq. TIMBER FRAME

TIMBER RAILS

SUPPORT ANGLES

LINER POSITIONED BY SPIDER

BRACKETS. TOP/BOTTOM

INSULATION BOUNDARY SHIELD

CUT CEILING MATERIAL

BACK 25mm CLEAR

OF BOUNDARY SHEILD.

CEILING

300

CONDITIONS FOR FLUES (Refer Fig. E)

1. The FLUE shall extend to:

Not less than 600mm above the highest

point on the roof if within 3.0m of that point,

Not less than 1000mm above the

intersection point with the roof and not lower

than any point of the roof within 3.0m.

In any case the length of the flue shall not be

less than 4.6m from the ash floor protector.

In some situations the Local Council may

vary the above requirements.

2. The flue system must be tested and comply

with AS/NZS2918:2001, Appendix F.

3. The insulation boundary shield shall be

capable of preventing accidental migration of

loose-fill or any combustible material by any

action of wind or by persons moving in the

ceiling space.

These instructions spare parts information,

operation and maintenance guides may be

downloaded from www.yunca.co.nz

FIG B

FIG B.

Note! All Dimensions are in millimetres

Monte Multi & Monte Euro Multi Installation - AUG_2014.doc www.yunca.co.nz Page 3 of 4

FIG. C: HEATER DIMENSIONS & WATER BOOSTER POSITION –Monte MF & Euro MF

(not to scale)

FIG.D: HEATER POSITION. (Not to scale)

Above: Non combustible wall clearances. Brick lining.

From the floor to within 25mm of ceiling. Leave air vents at

the bottom to allow airflow in the cavity. If Yunca flue

mounted shield is fitted, brickwork may be 1200mm high as

long as all vertical joints in top and bottom of brickwork are

left out to allow airflow when brickwork is capped.

FIG D: MINIMUM FIRE TO COMBUSTABLE WALL CLEARANCES –MONTE MF & Euro MF

(WITH YUNCA FLUE MOUNTED SHIELD FITTED). Measurements in millimetres.

150

400

200

314

732

519

FIG D: MINIMUM FLOOR PROTECTION MEASUREMENTS

(WITH YUNCA FLUE MOUNTED SHIELD FITTED). Measurements in millimetres.

300

125

913

947

1367

1208

633

663

647

FOR ACCESS

Monte Multi & Monte Euro Multi Installation - AUG_2014.doc www.yunca.co.nz Page 4 of 4

FIG E: FLUE SYSTEM REQUIREMENTS (not to scale)

More than 30003000

or less

600 min.

3000

1000 min. if clear

within 3000 of

flue top

3000

Any nearby

structure

1000 min. if clear

within 3000 of

flue top

MINIMUM HEIGHT OF FLUE SYSTEM EXIT

NOTE : Dimensions are in millimetres

3000

or less

600 min.

More than 3000

3000

Increase from

1000 min. until

clear within

3000 of flue top

IMPORTANT INFORMATION

A. The appliance and flue system shall be installed in compliance with AS/NZS 2918:2001 and

the appropriate requirements of the relevant building code or codes.

B. Mixing of appliance or flue system components from different sources or modifying the

dimensional specification of components may result in hazardous conditions. Where such

action is considered, the manufacturer should be consulted in the first instance.

C. Cracked and broken components e.g. glass panels or fire bricks, may render the installation

unsafe.

IF A WATERBOOSTER IS FITTED:

A. Do not connect to an unvented hot water system

B. Install in accordance with AS 3500.4.1 or NZS 4603 and the appropriate requirements of the

relevant building codes.

Seismic Restraint

Secure the heater base to the hearth or sub-framing with Dynabolts or similar, through the holes

provided in the heater base.

Follow local Council’s Specifications.

The Yunca Monte Multi-Fuel and Monte Euro Multi-Fuel are NOT clean-air approved.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Yunca Heating Brenner Handbücher

Yunca Heating

Yunca Heating HOBSON Betriebsanleitung

Beliebte Brenner Handbücher anderer Marken

Riello

Riello RS 28/M Kurzanleitung

True Induction

True Induction TI4B Bedienungsanleitung

Weishaupt

Weishaupt WG20 Series Bedienungsanleitung

Carolina Cooker

Carolina Cooker M116672 Bedienungsanleitung

Riello

Riello RX 500 S/PV Bedienungsanleitung

Unigas

Unigas HTP2000 Bedienungsanleitung

baltur

baltur BT 250 DSG 4T Bedienungsanleitung

muenkel design

muenkel design round burner Bedienungsanleitung

Ecoflam

Ecoflam Multicalor 170.1 Bedienungsanleitung

baltur

baltur BT 14 DSGW Bedienungsanleitung

artisan

artisan Art-SB1 Leitfaden

Riello

Riello P 140 T/G Kurzanleitung

AESYS

AESYS TurboFire II Bedienungsanleitung

Riello

Riello RG1RKD Kurzanleitung

IKEA

IKEA GRILLSKÄR Bedienungsanleitung

RUSTA

RUSTA SAREK Bedienungsanleitung

PROPOINT

PROPOINT 8933657 Bedienungsanleitung

baltur

baltur TBL 1000 ME Referenzhandbuch