Z Microsystems 15 Bedienungsanleitung

Doc# 27-0002UM Issued 7/99 Rev. 1.2

Z Microsystems

FIELD-READY

COMMAND

CONSOLE

Z Microsystems

FIELD-READY

User Manual

Doc# 27-0002UM Issued 7/99 Rev. 1.2

1. Use the power

and video

cab es supp ied

with the

Command

Conso e to he p

prevent

interference

with radio and

te evision

reception. The

use of cab es

and adapters

may cause

interference

with e ectronic

equipment in

the vicinity of

this unit.

2. This equipment

is pending

approva for a

C ass A digita device,

pursuant to certain imits

imposed by Part 15 of the

FCC ru es. These imits are

designed to provide

reasonab e protection

against harmfu interference

in a residentia insta ation.

This equipment generates,

uses and can radiate radio

frequency energy, and, if not

insta ed and used in

accordance with the

instructions, may cause

harmfu interference to radio

communications. However

there is no guarantee that

interference wi not occur in

a particu ar insta ation. If

this equipment does cause

harmfu interference, to

radio or te evision reception,

which can be determined by

turning the equipment off

and on, the user is

encouraged to try to correct

the interference by one or

more of the fo owing

measures:

 Reorient or re ocate the

receiving antenna.

 Increase the separation

between the equipment and

receiver.

 Connect the equipment into

an out et on a circuit

different from that to which

the receiver is connected.

 Consu t your dea er or an

experienced radio/TV

technician for he p.

3. If necessary, the user shou d

contact the dea er or an

experienced radio/te evision

technician for additiona

suggestions. The user may

find the fo owing book et,

prepared to be the FCC,

he pfu : How to Identify

and Reso ve Radio-TV

Interference Prob ems. This

book et is avai ab e from the

U.S. Government Printing

Office, Washington, DC,

20402, Stock No. 004-

00345-4.

FCC INFORMATION

Regulatory

COMMAND

CONSOLE

Doc# 27-0002UM Issued 7/99 Rev. 1.2

STARTING POINT 4

Shipment Contents 4

User Manua 4

System Requirements 4

Product Description 5

PREPARATION 6

INSTALL RAILS 7

INSTALL CONSOLE 9

FINAL ADJUSTMENTS 10

SETUP 11

CLOSING CONSOLE 12

OPERATION 13

CONFIGURE MONITOR 14

Setup For Windows 95 or 98 14

Auto Setup 15

Auto Setup for DOS 15

Auto Setup for Windows 3.1

95, 98 or NT 16

ADJUSTMENTS 18

User Contro Features 18

Operation 18

OSD Lock/Un ock 19

On-Screen Disp ay (OSD) 19

OSD Functions 20

MAINTENANCE 23

TROUBLESHOOTING 24

Causes and Corrective Action 24

APPENDICES 26

Disp ay Modes 26

Power Management 27

SPECIFICATIONS 28

Disp ay Specifications 28

Supported Disp ay Modes 28

Communications 28

Power Input 28

Power Consumption 28

Performance Tested 28

Environmenta Specifications 28

Regu atory 29

Re iabi ity Specifications 29

Deve opmenta Options 29

SUPPORT 30

Further He p 30

Rep acing Parts 31

Providing Feedback 31

Y2K COMPLIANCE 32

DRAWINGS 33

Contents

Doc# 27-0002UM Issued 7/99 Rev. 1.2

The User Manua comes in two

formats: printed hardcopy or CD-

ROM. This Manua is a so avai ab e

on the Z Microsystems website

(www.zmicro.com).

We recommend you read this manua

as fo ows:

Carefu y fo ow the instructions in the

Insta ation and Testing chapter for

hookup and initia contro settings.

Refer to the Operation chapter for a

comp ete description of a the user

contro s, and the Maintenance and

Troub eshooting chapters for care and

correcting any unforeseen prob ems

with the system. The Appendices and

References chapters are provided for

quick y finding technica information

about the Command Conso e.

SYSTEM REQUIREMENTS

The Command Conso e works with

any computer system that provides

industry standard screen formats from

640 x 480 to 1280 x 1024, with up to

75 Hz vertica sync. See the Specifica-

tions Tab e of this Manua for a

comp ete isting of a reso utions

supported.

The Command Conso e requires a

computer with a suitab e onboard

subsystems for Video Adapter Card

that can support XGA 1024 x 768,

SVGA 800 x 600, or VGA 640 x 480

at 60 Hz

The Command Conso e shipping box

contains the fo owing:

 The Command Conso e Unit

 Video Signa Cab e

 AC/DC Power Supp y Brick with

attached DC cab e

 AC Power Cab e

 Setup Diskette

 User Manua

Remember to save your origina

shipping container and packing

materia to transport or ship the

Command Conso e.

USER MANUALSHIPMENT CONTENTS

Doc# 27-0002UM Issued 7/99 Rev. 1.2

PRODUCT DESCRIPTION

The Command

Conso e provides

a iquid crysta

disp ay, a desk

work surface and

storage for any

size keyboard

and mouse in a

3.5" high (2U)

standard 19"

rack or transit

case.

Specia y de-

signed ocks on

each side of the

Command

Conso e ho d the

compact fo ded

unit secure y in

p ace during

storage.

Re ease of the

two Z-Locks on

the front sides of

the Conso e

a ow it to s ide

out and the LCD

disp ay to quick y

swing up into a

reading position

By ifting up the

desktop, the

keyboard and

mouse can be

easi y removed

and set on top.

The ightweight and durab e a umi-

num construction provides exceptiona

strength in fie d app ications.

The high qua ity LCD screen provides

fu co or and features up to 1280 x

1024 pixe reso ution.

The LCD screen has a back ight

contro that reduces power and

extends the ife of the monitor.

The side-viewing ang e is up to 160

degrees. It can be easi y adjusted to

any vertica -viewing ang e up to 100

degrees. The disp ay works effective y

with any workstation.

An e ectrostatica y-app ied and

baked-on finish is used for extreme

durabi ity for shipboard, airborne,

fie d dep oyments, and industria or

ab app ications where weight and

size are very critica .

Doc# 27-0002UM Issued 7/99 Rev. 1.2

TOOLS REQUIRED

PRECAUTIONS

Required Too s and Equipment

 F athead screwdriver with about 10"

shaft.

 Phi ips screwdriver with about 10"

shaft.

 Computer Setup Diskette

In preparation to insta the Com-

mand Conso e, take the fo owing

precautionary steps:

Turn off the e ectrica power to your

computer.

Verify the Command Conso e power

switch is off. If the Conso e is off, the

ight wi not be i uminated.

DANGER: To avoid shock hazard:

 Do not remove the covers around

the Command Console.

 Do not connect or disconnect the

Command Console during an

electrical storm.

 The power cord plug must be

connected to a properly wired

and grounded power outlet.

 Any equipment to which the

Command Console will be

attached must also be connected

to properly wired and grounded

power outlets.

OTE: For the fastest and easiest

installation of the

Command Console, follow

these steps in the sequence

they are presented.

Starting Point

Doc# 27-0002UM Issued 7/99 Rev. 1.2

SLIDE REMOVAL

With the Conso e sitting

on a workbench with the

front facing towards

you, press down to

re ease the Z-Locks on

each side of the front of

the Conso e to s ide the

side rai s back.

The s ide rai wi reach

a stop about ha f way

back.

This is a safety stop to

prevent the Conso e

s iding out too far whi e

mounted to the rack.

Simu taneous y press in

the safety catches on

each s ide rai and s ide

the side rai s a the way

off the back of the

Conso e.

The s ides shou d now

be separated from the

Conso e.

Each s ide unit inc udes

the s ide rai , with the

front Z- ock mount and

the rear mount.

On the front of the

cabinet frame, use three

Phi ips screws on each

side to secure the right

and eft Z-Lock mounts.

DO NOT tighten these

screws to a ow for

adjustment of the

Conso e within the

cabinet frame.

On the rear of the

cabinet frame, use the

two Phi ips screws to

oose y secure the right

and eft rear s ide mount

to the cabinet frame.

DO NOT tighten these

screws fu y at this time.

On the s ide rai s, using

a s ot screwdriver,

oosen off the screw.

Repeat on each side.

INSTALL THE SLIDES IN THE CABINET FRAME

Install Rails

Doc# 27-0002UM Issued 7/99 Rev. 1.2

Install Rails

Go back on the rear of

the cabinet frame, and

tighten the s ide mount

to the cabinet frame.

Make sure you ho d the

s ide mounts hard

against the rack rai .

Doc# 27-0002UM Issued 7/99 Rev. 1.2

INSTALL THE COMMAND CONSOLE IN THE SLIDES

Pu the two Conso e

s ides out unti they ock.

Ho d the Conso e by

each side, with the front

toward you.

Feed the four cab es

coming out of the

Conso e back through

the cabinet frame.

Guide the Conso e into

the s ides and s ide the

Conso e in unti it stops.

Simu taneous y press in

the catches on each

s ide and s ide the

Conso e a the way into

the cabinet frame.

The Conso e shou d

s ide in and out easi y.

S ide the Conso e in

and out severa times.

The Conso e shou d

easi y c ose comp ete y.

To be sure the s ide and

mount assemb y are

a igned proper y, s ide

the Conso e in and out

severa times.

If the Conso e binds

during s iding, do the

fo owing:

Because of variances in

cabinet frames, there

may need to be some

adjustments of the

Conso e s ide system for

best fit and movement

of the Conso e in and

out.

TEST INSTALLATION AND MAKE ADJUSTMENTS

Install Console

Doc# 27-0002UM Issued 7/99 Rev. 1.2

Loosen the screws on

each of the front Z-Lock

mounts.

FINAL ADJUSTMENTS OF THE COMMAND CONSOLE

S ide the Conso e

partia y out.

Use a f athead screw

driver to s ight y move

the Z-Locks out away

from the Conso e.

Tighten a the screws on

the front Z-Lock mounts.

S ide the Conso e in and

out to see if it moves

smooth y.

Go back to the rear of

the rack and fu y

tighten the side rai

screws.

Note: A wrench may be

necessary to hold the

nut on the other side.

Install Console

Andere Handbücher für 15

Dieses Handbuch passt für folgende Modelle

Andere Z Microsystems LCD-Schublade Handbücher

Z Microsystems

Z Microsystems 19 Bedienungsanleitung

Beliebte LCD-Schublade Handbücher anderer Marken

Acnodes

Acnodes KD 8228 Bedienungsanleitung

Ameriwood

Ameriwood 9524328PCOM Bedienungsanleitung

Kesseböhmer

Kesseböhmer TANDEM solo Bedienungsanleitung

Crystal Image Technologies

Crystal Image Technologies RMD-151-A Series Bedienungsanleitung

APW Wyott

APW Wyott Ease Extreme HDX-1-120 Bedienungsanleitung

NTI

NTI RACKMUX-V17-N Bedienungsanleitung

Austin Hughes

Austin Hughes CyberView L120 Bedienungsanleitung

Uplift Desk

Uplift Desk STR018 Bedienungsanleitung

Acnodes

Acnodes KDC 81932 Bedienungsanleitung

Acnodes

Acnodes RK1200T Bedienungsanleitung

StarTech.com

StarTech.com DuraView RACKCONS1501 Bedienungsanleitung

Mocka

Mocka Mischa Bedienungsanleitung

GRASS

GRASS DWD XP Bedienungsanleitung

StarTech.com

StarTech.com DuraView RACKCONS1701 Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel IZONA CoolDrawer RB36S Bedienungsanleitung

Synergy Global Technology

Synergy Global Technology LCD1U17-44 Bedienungsanleitung

Fujitsu

Fujitsu RC25 Bedienungsanleitung

Acnodes

Acnodes RK 1000B Bedienungsanleitung