Zenit Powertools SEMI-PROFI Series Bedienungsanleitung

INSTRUCTION MANUAL

ELECTRIC CHAIN SAW

ECS-406/2800 pROfI

SEMI-PROFI SERIES

General safety precautions

WARNING! When using electric tools, basic safety precautions should always

be followed to reduce the risk of re, electric shock and personal injury, including the

following.

Read all these instructions before operating this product and save these instructions.

For safe operations:

1. Keep work area clean. Cluttered areas and benches invite injuries.

2. Consider work area environment. Do not expose power tools to rain. Do not use

power tools in damp or wet locations. Keep work area well lit. Do not use power tools

where there is risk to cause re or explosion.

3. Guard against electric shock. Avoid body contact with earthed or grounded surfaces.

(e.g. pipes, radiators, ranges, refrigerators).

4. Keep children and inrm persons away. Do not let visitors touch the tool or

extension cord. All visitors should be kept away from work area.

5. Store idle tools. When not in use, tools should be stored in a dry, high or locked up

place, out of reach of children and inrm persons.

6. Do not force the tool. It will do the job better and safer at the rate for which it was

intended.

7. Use the right tool. Do not force small tools or attachments to do the job of a heavy

duty tool. Do not use tools for purposes not intended

8. Dress properly. Do not wear loose clothing or jewelry; they can be caught in

moving parts. Rubber gloves and non-skid footwear are recommended when working

outdoors. Wear protecting hair covering to contain long hair.

9. Use eye protection. Also use face or dust mask if the cutting operation is dusty.

10. Connect dust extraction equipment. If devices are provided for the connection of

dust extraction and collection facilities ensure these are connected and properly used.

11. Do not abuse the cord. Never carry the tool by the cord or yank it to disconnect it

from the receptacle. Keep the cord away from heat, oil and sharp edges.

12. Secure work. Use clamps or a vise to hold the work. It is safer than using your

hand and it frees both hands to operate tool.

13. Do not overreach. Keep proper footing and balance at all times.

14. Maintain tools with care. Keep cutting tools sharp and clean for better and safer

performance. Follow instructions for lubrication and changing accessories. Inspect

tool cords periodically and if damaged, have it repaired by authorized service center.

Inspect extension cords periodically and replace, if damaged. Keep handles dry, clean,

and free from oil and grease.

15. Disconnect tools. When not in use, before servicing, and when changing

accessories such as blades, bits and cutters.

16. Remove adjusting keys and wrenches. Form the habit of checking to see that keys

and adjusting wrenches are removed from the tool before turning it on.

17. Avoid unintentional starting. Do not carry a plugged in tool with a nger on the

switch. Ensure switch is off when plugging in.

18. Use outdoor extension leads. When tool is used outdoors, use only extension cords

intended for outdoor use.

19. Stay alert. Watch what you are doing. Use common sense. Do not operate tool

when you are tired.

20. Check damaged parts. Before further use of the tool, a guard or other part that is

damaged should be carefully checked to determine that it will operate properly and

perform its intended function. Check for alignment of moving parts, free running of

moving parts, breakage of parts, mounting and any other conditions that may affect

its operation. A guard or other part that is damaged should be properly repaired or

replaced by an authorized service center unless otherwise indicated in this instruction

manual. Have defective switches replaced by an authorized service center. Do not use

the tool if the switch does not turn it on and off.

21. Warning Use only accessories or attachments recommended in this instruction

manual or in the catalogue of ZENIT ТМ.

22. Have your tool repaired by a qualied person. This electric tool is in accordance

with the relevant safety requirements. Repairs should only be carried out by

qualied persons using original ZENIT TM spare parts. Otherwise this may result in

considerable danger to the user.

Safety precautions on using electric chain saw

• Do not expose power tools to rain or wet conditions.

• Before use check power cord for cracks or other damage. Replace cord if necessary.

• Always hold the chain saw rmly with both hands.

• Keep bystanders away.

• Before any work on the machine itself, pull the mains plug from the socket.

• When idle store in a secure place.

• When transporting the chain saw always t the guide bar cover.

• Fully grip both handles at all times during operation.

• Use the chain saw only with secure footing.

• If the power cord is damaged disconnect it from the receptacle.

• Never work with the tip of the chain bar.

• Do not operate the chain saw in in the presence of ammable liquids or gases.

• Connect the chain saw only to grounded power sources. It is recommended to use

residual current devices (RCD). Mains must be protected by a 16А fuse.

• In case of using extension cord in a drum it must be completely unwound.

• Do not use twisted or damaged power cord.

• Do not connect the chain saw to mains before it is completely assembled.

• In case of any malfunction immediately turn off the chain saw.

• Always carry rst-aid kit when operating the chain saw.

• In case of contact the chain saw with ground, stones, nails and other objects

immediately disconnect the chain saw from the power source and inspect chain and

guide bar.

• When operating make sure that oil from chain doesn’t get on the ground or in the

sewage drain. To avoid this put nonoperational chain saw on the shim which can

absorb oil.

To avoid kickback

ATTENTION! be alert against kickback when saw kicks up and back at

operator. Never cut with the tip of the bar.

• Do not touch trunks and limbs with the tip of the bar.

• Use working platform is possible.

• When operating always control tip of the guide bar.

• Do not operate a chain saw in a tree.

• Do not attempt a boring cut if you are not properly trained. A boring cut involves the

use of the nose of the guide bar and can result in kickback.

Rules for operation

• Before operation make sure there is enough light in the working area.

• When operating do not lean forward.

• Make sure you have a secure foothold.

• Never operate the chain saw standing on stairs.

• Never operate the chainsaw above the shoulder level.

• Do not cut materials other than wood or wooden objects.

• Never climb a tree when operating the chain saw.

• Watch for ying debris.

• Do not use the chain saw as a lever or a crowbar. Cut only with the lower part of the

chain. Otherwise it may lead to a kickback.

• Make sure the material to be cut does not include stones, nails and other objects.

ATTENTION! after stopping the motor the chain will rotate for some time by

inertia – INJURY DANGER!

Description

1. Main handle;

2. Attachment for the cord;

3. «On\Off» switch;

4. Service cover for quick graphite brushes change;

5. Front handle;

6. Front protective device with chain stop function;

7. Screw-nut for cover and guide bar fastening;

8. Guide bar

9. Chain

technical specifications

Model ECS-406/2800 pro

Rated voltage 220-240 V

Rated frequency 50-60 Hz

Rated power 2800 W

Max chain speed 14.0 m/s

Bar size 406 mm

Gross/net weight 6.0/5.3 kg

Standard accessories list is subject to change without prior notice.

how to use

1. Filling oil tank

Never operate the chain saw without chain oil or at an empty oil tank level, as this will

result in damage to the product. Never use exhaust oil for lubrication. To ll the oil

tank disconnect the tool from the power source. Thoroughly clean the area around the

oil tank.

Unscrew the cap and put it aside.

Pour about 200 ml of oil and screw on oil ller cap. You can check the oil level

through a special oil-level gauge. If the chain is stored for a long period of time drain

the oil. Drain oil before transporting the chain saw or chain removal.

2. Chain and bus assembly

ATTENTION! always wear safety goggles and gloves. Disconnect the tool

from the power source.

To perform assembly use the supplied wrench. Perform following actions:

• unscrew xing nut

• remove sprocket cover

• turn the adjusting screw to the left, till the boss reaches end of its travel

• install the saw chain in such a way so that cutting edges of the chain were facing

clockwise.

• the chain should stay on the bar and the boss of the chain tension should t into the

whole of the bar

• install the case and x it with screws. The saw chain is correctly tensioned when it

can be raised approx. 3-5 mm from the bar in the center nally tighten the xing nut

with a wrench.

ATTENTION! in case of chain whipping or getting out of the groove in the bar

adjust tension immediately.

ATTENTION! before connecting the saw to the mains make sure that the

switch returns to “Off” position after pressing and releasing. If it is not, do not connect

the saw to mains.

Chain brake is a protecting device which is activated after pressing the front guard.

Check chain brake operation before every operation.

3. Operation

Limbing

Make the rst cut 15 cm from a tree trunk on the lower part of the branch. To make

a cut use upper part of the guide surface. Do not cut too deeply, about 1/3 of the

diameter is enough.

Move 10 - 15 cm to the branch edge. Make the second cut. Continue cutting until the

branch is cut.

Make the third cut on the lower part of the branch as close to the trunk as possible.

Cutting depth must be about 1/3 of the branch diameter.

Make the fourth cut through the third cut. Cut from up to down towards the third cut.

This will make the cut branch fall.

Felling.

Make sure no bystanders are in the zone with radius of two lengths of the tree to be

cut. Prepare a path retreat away from felling direction. Keep rm footing. Remove all

foreign objects.

Stand to the side of the saw when cutting.

Before making a notch take into account the direction of the natural lean in order to

determine direction of its felling.

Make the rst horizontal cut. The depth of the cut should be about 1/3 of the log

diameter.

Make an upper cut at an angle about 45° to the rst one. Remove wedge cut from the

notch.

Make a cut on the opposite side of the tree 5 cm higher than the lower edge of the

notch.

Keep cut alignment to the lower edge of the notch.

When the cut reaches the axis, the tree will start to fell. Insert a wedge or a felling

lever in the cut well before the tree becomes unstable. Use only wedges made of

plastic, wood or aluminum. Never use wedges made of steel. This can cause kickback

and chain damage.

Maintenance anD inspection

ATTENTION! before maintenance switch off the saw, disconnect from the

power source, and x its position.

Do not forget to remove oil and chips after operation. To avoid overheating timely

clean the vent holes in motor case. In case of heavy choking disassemble the chain and

clean it separately. To do this put chain in a special cleaning solution for a couple of

hours and rinse with clean water.

Do not store chain saw outdoors at increased humidity. Check saw after each use.

Regularly check chain tension. When the chain is loosened it may cause serious

injury. In case of chain damage immediately replace it. Every time after operation

check motor frame and power cord possible damage. In case of damage contact an

authorized service center.

After operation check oil level in chain lubrication system.

Insufcient oil leads to chain, bar and motor damage.

ATTENTION! When using the chain saw follow these rules:

• continuous use of the power tool should not exceed 15 minutes;

• do not allow mechanical damage (strikes, falls etc.);

• protect the power tool from external sources of heat and chemically active

substances, as well as liquid and objects penetration;

• before disconnecting the tool from the power source turn off the On/Off switch;

• check the motor temperature, do not allow overheating;

• change the rotation direction only after switching off the tool and complete stop of

rotating parts.

Inobservance of these rules will make warranty void!

WARNING! Repair, modication and check of ZENIT power tools should be

performed only in authorized service centers ZENIT. While use or maintenance of

power tools follow all safety rules and standards.

NOTE

Zenit Power Tools are constantly being improved and modied to incorporate the

latest technological advancements. Accordingly, some parts may be changed without

prior notice.

Demix LLC

Head ofce:

14, Shevchenko str., 3rd oor

Dnepropetrovsk, Ukraine, 49044

tel./fax: +38 056 375-43-16

http://www.en.zenit-pro.com

Andere Handbücher für SEMI-PROFI Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Zenit Powertools Kettensäge Handbücher

Zenit Powertools

Zenit Powertools CS-508/2300 Bedienungsanleitung

Beliebte Kettensäge Handbücher anderer Marken

Bushranger

Bushranger CS4210 Bedienungsanleitung

Husqvarna

Husqvarna 136, 141 Bedienungsanleitung

Echo

Echo CS-330EVL Bedienungsanleitung

HART

HART HLCS01 Bedienungsanleitung

Homelite

Homelite UH10817 Bedienungsanleitung

Westfalia

Westfalia SCS 725 Bedienungsanleitung

Nakayama

Nakayama EC2050 Bedienungsanleitung

The Handy

The Handy THPCS16 Bedienungsanleitung

McCulloch

McCulloch PRO MAC 54 Handbuch

Husqvarna

Husqvarna 359 E-tech Bedienungsanleitung

Craftsman

Craftsman 358.352162 Bedienungsanleitung

Craftsman

Craftsman 358.350270 Bedienungsanleitung

Craftsman

Craftsman 358.351610 Bedienungsanleitung

Echo

Echo CS-8001(6digits)(36) Bedienungsanleitung

Poulan Pro

Poulan Pro 545047544 Bedienungsanleitung

Ryobi

Ryobi RY3714VNM Bedienungsanleitung

Homelite

Homelite Ranger UT10926 Bedienungsanleitung

McCulloch

McCulloch TimberBear TM502 Bedienungsanleitung