Zenith INTEQ SRX3253 Bedienungs- und Wartungshandbuch

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT

REMOVE COVER (OR BACK). NO USER SERVICEABLE

PARTS INSIDE. REFER TO QUALIFIED SERVICE

PERSONNEL.

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE

THIS PRODUCT TO RAIN OR MO][STURE.

The lightning flash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of uninsula_:ed

"dangerous voltage" within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to

alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the appliance.

Safety Tips

Refer to the "Safety Tips" booklet that came with your

product for important safety considerations.

Note to Cable TV System Installer

This reminder is provided to call the cable TV system

installer's attention to Article 82,3-40 of the NEC that

provides guidelines fi_r proper grounding and, in particular,

specifies that the cable ground shall be connected to the

grounding system of the building, as close to the point of

the cable entry as practical.

Power-Cord Polarization

This product is equipped with a polarized

alternating-current line plug (a plug having one blade wider

than the other.) This plug will fit into the power outlet only

one way. This is a safety feature. If you are unable to insert

the plug tully into the outlet, try reversing the plug. If the

plug should still fail to fit, contact your electrician to

replace your obsolete outlet. Do not defeat the safety

purpose of the polarized plug.

CAUTION

To prevent electric shock, malch wide blade of plug to

wide slot, fully insert.

ATTENTION

Pour _viter les chocs _lectriques.r introduire la lame la plus

large de la fiche darts la borne correspondante de la prise et

pous ser jusqu' au fond.

INTQWRN

INTEQ is a trademark of Zenith Electronics Corporation.

CONTENTS

Part 1. Connections and Basic

Operations

INTRODUCTION

Welcome ............................................ ii

Installation Considerations .............................. ii

Methods of Operation ................................. iii

ModeVFeatures Chart ................................. iii

STANDARD CONNECTIONS FOR YOUR TV

Connection Center, Auxiliary A/V Jacks, TV Only,

TV and Cable Box, IV and VCR, TV with VCR

and Cable Box, Accessory Jacks, Surround

Speakers and Audio Amplifier ......................... 1-1

FIRST TIME YOU OPERATE YOUR TV

Control Panel, Battery Installation, Power, Source,

Auto Program,Clock, and Other Options ................ 2-1

PIP OPERATION

Introduction,Selecting Main Picture and PIP Inset

Source, PIP Functions, Operation With Various

Configurations ...................................... 3-1

Part 2. Universal Remote Control

and Menus

UNIVERSAL REMOTE CONTROL

Battery Installation, Operating Mode, TV Operations,

StarSight Operations, Operational Modes, Programming,

Special Features, Auto Find, and Brand Codes ............ 4-1

QUICK REFERENCE TO MENUS

Available Menus. and Basic Operation .................. 5-1

SOURCE MENU

Menu Operation, Source Selection.

and Source Identification ............................. 6-1

SETUP MENU

Auto Program, Ch. Add/Del, Ch. Labels, Source ID,

Clock: Set, Timer Setup, Parental Ctl, Caption/

Text, Background, and StarSight ....................... 7-1

AUDIO MENU

Bass, Treble, Balance, Audio, SEQ,

Surround and Null .................................. 8-1

VIDEO MENU

Contrast, Brightness, Color, Tint, Sharpness, Color

Temp, Video Filter, Auto Flesh, and Picture Pref .......... 9-1

PIP MENU

Ch. Guide, Ch. Review, PIP Color, PIP Tint,

and PIP Size ...................................... 10-1

Part 3. Z-Trak Remote Control

and Menus

Z-TRAK REMOTE CONTROL

Battery Installation, Operating Mode,

Basic Operations and Auto Find ........................ 11-1

QUICK REFERENCE TO MENUS

Available Menus, Accessing the Menu,

Channel Icons and Volume Control ..................... 12-1

TV OPTIONS MENU

Timer, Captions, Z-Trak, PIP, Free;,e

and Mow_ PIP ...................................... 13-1

SOURCE MENU

Menu Operation, Source Selection,

and Source Identification ............................. 14-1

SETUP MENU o

Auto Program, Ch. Add/Del, Ch. Labels, Source ID,

Clock Set, Timer Setup, Parental Cfl, Caption/

Text, Background, and StarSight ....................... 15-1

AUDIO MENU

Bass, Treble, Balance, Audio, SEQ,

Surround, and Null .................................... 16-1

VIDEO MENU

Contrast, Brightness;, Color, Tint, Sharpness, Color

Temp, Video Filter, Auto Flesh, and Picture Pref .......... 17-1

PIP MENU

Ch. Guide, Ch. Review, PIP Color, PIP Tint,

and PIP Size ....................................... 18-1

Part 4. Maintenance, Accessories,,

and Warranty

MAINTENANCE AND TROUBLESHOOTING

Caring, Extended Absence, Interference,

Before Calling for Service ............................ 19-1

Replacement Product Registration Card

Your Inteq Warranty

How to use this operating guide

Standard TV installation and operation is given in this portion of the operating guide. Follow the procedures given if you will not

be using StarSight®.

_k Refer to the StarSight® portion of this operating guide for StarSight® activation and operation.

2949-1)!-A i

INTRODUCTION

WEL COME

Welcome into the family of 11-7TEO- Color Television

owners. This guide provides instructions on how to operate

your new TV. It is supplemented by a booklet containing

Safety Tips. We urge you to read these publications carefully

so that you will receive full enjoyment from your new

II-lTl:::z:l_)'- "IN for many years to come.

Your new TV has been designed and built to give you the very

besl in quality, features and performance. There are thousands

of I[-"ITEIS_- authorized service centers throughout the

U.S., Canada and Mexico who can attend promptly and effec-

tively to ordinary service needs.

If you should have an unusual performance or service problem

that cannot be satisfactorily resolved by your I/'-]TEI_-

dealer or IN-[-E[_- authorized service center, contact us at:

IF'qTEC_-

Customer Service Department

1000 Milwaukee Avenue

Glenview, IL 60025-2493

Telephone: (708) 391-8752

Mon-Fri, 8:00 a.m. - 4:30 p.m. Central Time

Send the model number, serial number, and date of purchase

or original installation, with a full explanation of the problem

and the service history. We will welcome the opportunity to

took in,to your specific question or problem and to be of assis-

tance in resolving it promptly.

The mcdel and serial numbers of },oar new TV are located on the

back of the TV cabinet. For your future convenience and protec-

tion, we suggest that you record these numbers here:

Model No.

Serial No.

rID iDOmYSURROUNDI

PRO •LOGIC

Manufactured under license from Dolb3, l_;tboratories Licensi ag Corporation.

Additionally licensed under Canadian patent number 1,037,877. "l)olby",

"Pro Logic" and the double-I) symbol are trademarks of DoWy Laboratories

Licensing Corporation.

INSTALLATION CONSIDERATIONS

Before you install your TV...

Ventilation -- Proper ventilation keeps your TV

running cool. Air circulates through perforations

in the back and bottom of the cabinet. Do not

block these vents or you will shorten the life of

your TV.

Power Source -- Your TV is designed to operate

on normal household current, 120 volt 60 Hertz AC.

Do not attempt to operate it on I)(2 current.

Power Cord -- Your power cord has a polarized

plug as required by Underwriters' Laboratories. It

has one regular blade and one wide blade and fits

only one way into a standard electrical outlet. If

the blades will not enter either way, your outlet is

very old and non-standard. A new outlet should be

installed by a qualified electrician.

Safe Operation -- Your TV is manufactured and

tested with your safety in mind. However, unusual

stress caused by dropping or mishandling, expo-

sure to flood, fire, rain or moisture, or accidental

spilling of liquids into the TV, can result in poten-

tial electrical shock or fire hazards. If this hap-

pens, have your TV checked by a service

technician before using it again.

PLEASE READ AND OBSERVE EACH SAFETY

POINT IN THE "SAFETY TIPS" FOLDER 'WHEN IN-

STALLING AND USING YOUR TV.

VIDEO GAMES AND OTHER FIXED

PATTERN DISPLAY CAUTION -- If you use your TV for

video games, teletext or other fixe:l displays, avoid setting the

BRIGHTNESS control for an excessively bright picture. A

bright, fixed pattern, if used for long periods of time, can

result in a permanent imprint on the TV picture tube. You

can reduce this possibility by alternating the use of the fixed

pattern display with normal TV picture viewing, by turning

down the CONTRAST control for sustained fixed pwLtern use,

and by turning off the fixed pattern display when not in use.

PLUGGING IN YOUR TV --- Be sure to plug your TV into

an "unswitched" AC power source. The "switched" AC out-

lets fo_and on some video equipment will not continue supply-

ing power to the TV once the equipment is turnecl off. If the

power to the TV is interrupted, you will have to reset the clock

in the IN to the current time.

Jr,_r,_wEL ii

INTRODUCTION

METHODS OF OPERATION

Your new II---TT__[--_-TV is a very sophisticated appliance. Optional features, video picture adjustments and audio sound adjust-

ments are performed through on-screen menus and displays. Self explanatory ICONS are used throughout. Most features can be se-

lected and adjusted from the comfort of your favorite chair by using either of the infrared remote controls.

Either of two remote controls can be used to operate the TV. Use the multi-brand programmable remote if you have different brands

and types of equipment in your video system which you need to control remotely. Use the Z-Trak progr;unmable remote if you feel

comfertable using track-ball access similar to that provided by the familiar computer mouse device. Many features can be selected

and adjusted by using the control panel provided on the TV.

StarSight provides ',anelectronic programming guide which is updated with new scheduling information automatically on a periodic

basis. StarSight allows you to rapidly scan through the programming guide to find a program for viewing or recording. Programs

can be searched and selected by category if desired.

Method of Operation Standard TV StarSight °

Control Panel on TV. YES NO n

Universal Remote Control YES YES

[] 7-Trak Remote Control YES YES

FEATURES PROVIDED WITH YOUR TV

This operating guide describes a "family" of TV models. Not all models have all of the features described in this guide. In addition,

different control panels may be used from model to model. Most models include the following features:

--------_ MODEL

FEATURE

StarSight Electronic Program Guide

Q StarSight Demonstration

n On-Screen Menus Accessed By Remote

o: TV Contro's

nUniversal Programmable Remote Control

ca Z-Trak Programmable Remote Control

c_ Picture-In-Picture

[] 1_1ChannelTuning

[] Automatic Channel Programming

ca Favorite Channel Add/Delete

ca Channel Labels (ABC, TNT, etc.) for Easy

Channel Identification

n Multiple Input Sources

a Source Identification (VCR, Cable, etc.)

c) Antenna/Cable and Loop Out Jacks

ca Audio/Video (A/V) Jacks

[] Super-VHS A/V Input Jacks

ca Front Mounted ?UV Jacks

Surround Sound System

t_ MTS Stereo with SEQ (Spatial Equalization)

Surround Sound Speaker Terminals

u Variable Audio Output Jacks

Surround Sound Speakers

Sleep Timer and On/Off Timer

[] Closed Caption and Text Modes

ca Parental Control

SRX2793, IQ2793

SRX3293, SRX359, iSRX3253, SRX3553 i

IQ3293, IQ3593 IQ3253, IQ3553

Y Y

SRX3593 only

Dolby Pro Logic

No SEQ

Optional

Dolby

Optional

Dolby Pro Logic, Premium

No SEQ

Optional

2949-01-A iii

STANDARD CONNECTIONS FOR YOUR TV

CONNECTION CENTER

Locate the Connection Center on the back of the TV.

Use these to send the incoming

attdio and video (from Video 1 In)

to another component, such as a

second VCR.

TURN OFF POWER OR UNPLUG

TV BEFORE MAKING ANY

CONNECTIONS.

"vARIABLE AUDIO OUTPUT

Star,dard phono jack connectors for

output to an optional stereo ampli-

fier or to external speakers.

For Dolby Pro Logic TVs, do not

connect speakers directly to these

jacks.

SPEAKER EXT/INT

Select EXT (external) to remove

sound from the TV's s_akers.

Select INT (internal) to hear sound

ffor,_the TV's speakers.

Note that this switch doe:+not ap-

pear on TVs having the Dolby Pro

I_,o_icaudio system.

SURROUND SPEAKER

TERMINALS

Connections for output to optional

sunound sound spe_&ers.

S-VIDEO 1 IN

Jacks for audio and video input

from a Super-VHS VCR

ADDITIONAL A/V JACKS (Some Models)

If your TV model is equipped with the additional A/V input jacks, they are located behind a small door below the control panel on

the front of the TV.

S-VIDEO 2 IN

Jacks for audio and video input from a second Super-VHS VCR.

VIDEO 3IN

Jacks for audio and video input from a third stereo VCR or other

A/V component.

294_÷01-A 1-- 1

STANDARD CONNECTIONS FOR YOUR TV

SETUP 1: TV ONLY

If you receive your television signal by antenna or basic cable-

TV (no cable box), connect your television as shown here.

_k TURN OFF POWER OR UNPLUG TV BE-

FORE MAKING ANY CONNECTIONS TO

YOUR TV.

1. Attach the cable coming out of the wall jack O

to the "ANT/CABLE 1" jack on the back of your

TV.

2. Plug your TV into a power outlet that is not

controlled by a light switch.

3. If you want to activate StarSight, proceed to

"Step 2. Activate StarSight" in the StarSight

section of the operating guide.

CABLE A

Q r_s_.rr

m_mr_x

matxt

"iV E_ACK

Antenna or Basic Cable-TV Connection

SETUP 2: 71/AND CABLE BOX

If you receive your television signal from a cable box,

connect your television as shown in the illustration.

_k O NOT UNPLUG YOUR CABLE BOX

AT ANY TIME:

DO NOT PLUG YOUR TV INTO THE

BACK OF YOUR CABLE BOX!

1. Turn off, but do not unplug, your Cable Box.

2. Attach the cable coming out of the wall O to the

Cable Box's "Input" or "Cable In" jack.

3. Attach an RF cable O between your Cable Box's

"Output" or "TV Set" jack, and the "ANT/CABLE

1" jack on the back of your TV.

4. Take the Remote Emitter cable _ and plug the jack

into the "StarSight Control Port" on the back of the

TV. Route the Remote Emitter cable under the

('-able Box and place either one of the plastic bulbs

about two inches in front of the Cable

Box's front panel, as shown in the

illustration. Make sure that the plastic C,_t_A

bulb is facing the front panel O. Do not

adhere the Remote Emitter until after

you have completed activating StarSight

and you have confirmed the correct code

that operates your Cable Box. Once the

code is confirmed, peel off the backing of the

.,:ticker on the Remote Emitter and adhere it in

place.

TO FRONT OF _ ,_L_

[/_ ,N --_&"-.. ""_REMDTE _ ._

NOTE:

The Remote Emitter is only necessary if you are planning to

activate StarSight and want StarSight to control the channel

tuning of your cable box.

Cable Box Connection

5. Plug your TV into a power outlet that is rtot

controlled by a light switch.

6. If you want to activate StarSight, proceed to "Step

1. Fill out the StarSight Checklist" in the StarSight

section of the operating gaide.

2949-01-A 1 -- 2

STANDARD CONNECTIONS FOR YOUR TV

SETUP 3: "IV AND VCR

If you receive your television signal through your VCR, connect

your television as shown here.

1. Attach the cable coming out of the wall O to the

"VHF In" (From Antenna) jack of your VCR.

2. Attach an RF cable Obetween your VCR's "VHF

Out" (To TV) jack, and the "ANT/CABLE 1" jack

on the back of your TV.

3. Take the Remote Emitter cable I_ and plug the jack

into the "StarSight Control Port" on the back of the

TV. Route the Remote Emitter cable under the VCR

and place either one of the plastic bulbs about two

inches in front of the VCR's front panel, as shown

in the illustration. Make sure that the plastic bulb is

facing the front panelO. Do not adhere the

Remote Emitter until after you have completed

activating StarSight and you have confirmed the

correct code that operates your VCR. Once the

code is confirmed, peel off the backing of the

sticker on the Remote Emitter and adhere it in

place.

...... ;+

Standard VHS VCR Connection

iuNOTE:

The Remote Emitter is only necessary if you are planning to

activate StarSight and want StarSight to control the record

nctions of your VCR.

4. Locate the area of the TV's jack panel that is

labeled "Video 1 In" (or "S-Video 1 In"). Attach

the three Audio/Video (A/V) cables Oto the

"Video," "Audio R" and "Audio L" jacks and attach

the other ends of the cables to the corresponding

"Video Out," "Audio R Out" and "Audio L Out"

jacks on the back of your VCR. Connecting these

A/V cables is necessary if ...

[] You have a VCR without a front panel channel indica-

tor that uses an on-screen display.

[] You have a stereo VCR and would like to take advan-

tage of the stereo feature.

[] You would like to take advantage of the TV's PIP

feature.

5. Plug your TV into a power outlet that is not

controlled by a light switch.

6. If you want to activate StarSight, proceed to "Step

1. Fill out the StarSight Checklist" in the StarSight

section of the operating guide.

'TO FRONT OF VCR

Super-VHS VCR Connection

294.9-01-A 1-- 3

STANDARD CONNECTIONS FOR YOUR TV

SET'UP 4: "IV WITH VCR AND CABLE BOX

If yo,areceive your television signal through your VCR, connect

your television as shown here.

_k DO NOT UNPLUG YOUR CABLE

BOX AT ANY TIME!

DO NOT PLUG YOUR TV INTO THE

BACK OF YOUR CABLE BOX!

TO FRONT OF VCR srh'_l.n-

oom'_t.

AND CABLE BOX

1. l'urn off, but do not unplug, your Cable Box.

2. Attach the cable coming out of the wall O

to the "ANT/CABLE 2" jack on the back of

your TV.

3. Attach an RF cable Obetween your TV's

"LOOP OUT TO DECODER" jack, and the

Cable Box's "Input" or "Cable In" jack.

4. Attach an RF cable t_ between your Cable

Box's "Output" or "TV Set" jack, and the

VCR's "VHF In" (From Antenna) jack of

your VCR.

5. Attach an RF cable O between your VCR's

"VHF Out" (To TV) jack, and the "ANT/

CABLE 1" .jack on the back of your TV.

6. Take the Remote Emitter cable O and plug the jack

into the "StarSight Control Port" on the back of the

TV. Route one Remote Emitter wire under the VCR

and place its plastic bulb about two inches in front

of the VCR's front panel !_, as shown in the

illustration. Make sure that the plastic bulb is

facing the front panel. Do the same for the

Cable Box _. Do not adhere the Remote Emitters

until after you have completed activating

StarSight and you have confirmed the correct

codes that operate your equipment. Once the

codes are confirmed, peel off the backing of the

sticker on tlhe Emitters and adhere it in place.

NOTE:

The Remote Emitter is only necessary if you are planning to

activate StarSight and want StarSight to control the record

functions of your VCR and the channel tuning of your cable

bo_.

TV BAC, K

CABLE

BOX

.qONT

Cable Box and VCR Connection

7. Locate the area of the TV's jack panel that is

labeled "VidLeo 1 In." Attach the three Audio/Video

(AIV) cables tl) to the "Video," "Audio P" and

"Audio L" jacks and attach the other ends of the

cables to the corresponding "Video Out," "Audio R

Out" and "Audio L Out" jacks on the back of your

VCR. Connecting these A/V cables is necessary if ...

Cl You have a VCR without a front panel ch;mnel indica-

tor that uses an on-screen display.

Cl You have a stereo VCR and would like to take: advan-

tage of the',stereo feature.

O You would like to take advantage of the q-V's PIP

feature.

8. Pl_ag your TV into a power outlet that is not

controlled by a light switch.

9. If you want to activate StarSight, proceed to "Step

1. Fill out the StarSight Checklist" in the StarSight

section of the operating :guide.

_949ol-a 1 -- 4

STANDARD CONNECTIONS FOR YOUR TV

AUDIO/VIDEO (AN) CONNECTIONS FOR OPTIONAL VIDEO EQUIPMENT

Connections to VIDEO 3 IN

or S-VIDEO 2 IN jacks.

(Some TV models only.) Stereo Camcorder [__

I \ \

:" ; _i EO S-VIDEO 2 IN "

i:!i!i...... VioEO

[

OPTIONAL AUDIO AMPLIFIER/SURROUND SOUND CONNECTIONS TO TV °

If you wish to listen to the TV audio through an external amplifier or stereo system, or listen to surround sound audio, make the connec-

tions to the "IN" shown in the illustration below.

__ TURN OFF POWER OR UNPLUG TV BEFORE MAKING ANY CONNECTIONS TO YOUR TV.

731 BACK

To Speakers

,''""" .... _ AUX INPUT

' ,,," _ _ RSPKR OUTPL_RIT-_

,[,._, Back of Customer's

Stereo Amplifier

8 ohm

Surround

Speakers

"/'vBACK

_SILVER

8ohm

Surround

Speaker

Amplifier and Dual Surround Speaker Connections Single Surround Speaker Connection

DIFFERENT WAYS TO LISTEN TO YOUR TV

Surround Sound

[2 O rn

c_I

TV Speakers On

(Some Models Only)

SPEAKER EXT/INT switch in the INT

(internal) position --

TV speakers are ON. Sound is heard

from both the TV's speakers and the

external amplifier's speakers.

Use TV's volume control to raise and

lower the level of sound being heard

from both sets of speakers.

TV Speakers Off

(Some Models Only)

SPEAKER EXT/INT switch in the EXT

(external) position --

TV speakers are OFF. Sound is only heard

from the speakers connected to the external

amplifier.

Use TV's volume control to raise and

lower the level of sound being heard from

the amplifier's speakers.

Connect surround sound speakers as

shown. The level of surround sound will

vary, depending on the program being

viewed. Note that not all programs have

surround sound audio.

The SURROUND SPKR terminals are

always active. The SPEAKERS EXT/INT

switch does not affect the operation of

surround sound speakers.

If you want to connect only one sarround

speaker to your "IV, connect the speaker

wires to the :erminals adjacent to the

positive (+):and negative (-) symbols that

are circled.

294)-01-A 1 -- 5

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Zenith Fernseher Handbücher

Zenith

Zenith P42W46X - 42" Flat Panel Plasma ED-Ready TV Installationsanleitung

Zenith

Zenith H13E01L Bedienungs- und Wartungshandbuch

Zenith

Zenith SY3238 Bedienungs- und Wartungshandbuch

Zenith

Zenith HealthView H20C50DT Bedienungs- und Wartungshandbuch

Zenith

Zenith Concierge H19C34DT Bedienungs- und Wartungshandbuch

Zenith

Zenith Presentation H27D44DT Fehlerbehebungshandbuch

Zenith

Zenith L23W36 - 23" Widescreen Flat-Panel HD-Ready LCD... Bedienungsanleitung

Zenith

Zenith C27A25 Bedienungsanleitung

Zenith

Zenith C27A25 Bedienungs- und Wartungshandbuch

Zenith

Zenith B13A03D Bedienungs- und Wartungshandbuch

Zenith

Zenith Sentry 2 Series Bedienungs- und Wartungshandbuch

Zenith

Zenith Presentation H25E46DT Bedienungs- und Wartungshandbuch

Zenith

Zenith HealthView H20E50DT Bedienungs- und Wartungshandbuch

Zenith

Zenith A20A22D Bedienungsanleitung

Zenith

Zenith SL2784BT and Bedienungs- und Wartungshandbuch

Zenith

Zenith C32V37 Installationsanleitung

Zenith

Zenith SENTRY 2 SAR2035Y7 Bedienungs- und Wartungshandbuch

Zenith

Zenith A50M91W Series Bedienungsanleitung

Zenith

Zenith SY1931SG Bedienungsanleitung

Zenith

Zenith C19A02D Bedienungs- und Wartungshandbuch

Zenith

Zenith PVR5269 Bedienungs- und Wartungshandbuch

Zenith

Zenith Concierge H20C35DT Bedienungs- und Wartungshandbuch

Zenith

Zenith SENTRY 2 SMS2047W Bedienungs- und Wartungshandbuch

Zenith

Zenith IQA32M46W Series Bedienungsanleitung

Beliebte Fernseher Handbücher anderer Marken

Philips

Philips Colour Television Bedienungsanleitung

Toshiba

Toshiba 27A10 Bedienungsanleitung

Philips

Philips 42PF9630A/37 Bedienungsanleitung

Hitachi

Hitachi 32FX48B Bedienungsanleitung

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Bedienungsanleitung

Changhong Electric

Changhong Electric uhd55b6000is Bedienungsanleitung

Philips

Philips Matchline 21CE7551 Bedienungsanleitung

Panasonic

Panasonic Genus TX-G10 Bedienungsanleitung

Toshiba

Toshiba 19A20 Bedienungsanleitung

Philips

Philips 25PT4523-16 Bedienungsanleitung

Sony

Sony XBR-100Z9D Bedienungsanleitung

Philips

Philips PR0930X3 Bedienungsanleitung

Philips

Philips Brilliance 231P4QPY Bedienungsanleitung

Samsung

Samsung 55S9 B Series Bedienungsanleitung

Philips

Philips 32HF9385D Fehlerbehebungshandbuch

Sharp

Sharp LC-40FI5012E Bedienungsanleitung

Loewe

Loewe Table Stand Reference 55 Bedienungsanleitung

Philips

Philips 32PFH5300 Bedienungsanleitung