Zennio MAXinBOX 24 ZIO-MB24 Bedienungsanleitung

➢

MAXinBOX 24

Multifunction Actuator with 24 Outputs

ZIO-MB24

USER MANUAL

Application programme version: [1.1]

User manual edition: [1.1]_a

www.zennio.com

MAXinBOX 24

http://www.zennio.com Technical Support: http://support.zennio.com

CONTENTS

Contents ........................................................................................................................................ 2

Document Updates ....................................................................................................................... 3

1 Introduction .......................................................................................................................... 4

1.1 MAXinBOX 24 ................................................................................................................... 4

1.2 Installation........................................................................................................................ 5

1.3 Start-Up and Power Loss.................................................................................................. 6

2 Configuration......................................................................................................................... 7

2.1 General............................................................................................................................. 7

2.2 Outputs............................................................................................................................. 9

2.3 Manual Control .............................................................................................................. 10

2.4 Logic Functions............................................................................................................... 14

2.5 Scene Temporisation...................................................................................................... 15

ANNEX I. Communication Objects............................................................................................... 17

MAXinBOX 24

http://www.zennio.com Technical Support: http://support.zennio.com

DOCUMENT UPDATES

Version

Changes

Page(s)

[1.1_a]

Changes in the application program:

•Parameters reorganization.

MAXinBOX 24

http://www.zennio.com Technical Support: http://support.zennio.com

1INTRODUCTION

1.1 MAXinBOX 24

MAXinBOX 24 from Zennio is a versatile KNX actuator featuring a wide variety of

functions:

24 relay outputs, configurable as:

➢Up to 12 independent shutter channels (with or without slats),

➢Up to 24 individual ON/OFF outputs,

➢Up to 6two-pipe fan coil modules where both the fan speed control and

the valve control are performed through relays,

➢A combination of the above.

30 customisable, multi-operation logic functions.

Scene-triggered action control, with an optional delay in the execution.

Manual operation / supervision of the 24 relay outputs through the on-

board pushbuttons and LEDs.

Relay Switches Counter.

Heartbeat or periodical “still-alive” notification.

MAXinBOX 24

http://www.zennio.com Technical Support: http://support.zennio.com

1.2 INSTALLATION

MAXinBOX 24 connects to the KNX bus through the on-board KNX connector.

Once the device is provided with power from the KNX bus, both the individual address

and the associated application programme may be downloaded.

This device does not need any additional external power since it is entirely powered

through the KNX bus.

Figure 1. Element Diagram for MAXinBOX 24.

The main elements of the device are described next.

Prog./Test Pushbutton (5): a short press on this button sets the device into

the programming mode, making the associated LED (6) light in red.

Note: if this button is held while plugging the device into the KNX bus, the

device will enter into safe mode. In such case, the LED will blink in red every

0.5 seconds.

Outputs (1 and 2): output ports for the insertion of the stripped cables of the

systems being controlled by the actuator (see section 2.2). Please secure the

connection by means of the on-board screws.

To get detailed information about the technical features of this device, as well as on the

installation and security procedures, please refer to the corresponding Datasheet,

bundled with the original device packaging and also available at www.zennio.com.

1. Outputs.

2. Output status LED.

3. Manual Control Pushbutton

4. Fixing clamp.

5. Prog./Test LED Pushbutton.

6. Prog./Test LED Indicator.

7. KNX Bus Connector.

MAXinBOX 24

http://www.zennio.com Technical Support: http://support.zennio.com

1.3 START-UP AND POWER LOSS

During the start-up of the device, the Prog./Test LED will blink in blue colour for a few

seconds before the device is ready. External orders will not be executed during this

time, but afterwards.

Depending on the configuration, some specific actions will also be performed during

the start-up. For example, the integrator can set whether the output channels should

switch to a particular state and whether the device should send certain objects to the

bus after the power recovery. Please consult the next sections of this document for

further details.

On the other hand, when a bus power failure takes place, MAXinBOX 24 will interrupt

any pending actions, and will save its state so it can be recovered once the power

supply is restored.

For safety reasons, all shutter channels will be stopped (i.e., the relays will open) if a

power loss takes place, while the individual outputs and fan coil contacts will switch to

the specific state configured in ETS (if any).

MAXinBOX 24

http://www.zennio.com Technical Support: http://support.zennio.com

2CONFIGURATION

2.1 GENERAL

After importing the corresponding database in ETS and adding the device into the

topology of the desired project, the configuration process begins by entering the

Parameters tab of the device.

ETS PARAMETERISATION

The first parameterisable screen available by default is General. From this screen it is

possible to activate/deactivate all the required functionality.

Figure 2. General screen.

The Manual Control function is enabled by default. Once activated, Inputs, Outputs,

Logic Functions and Manual Control bring additional tabs to the menu on the left. On

the other hand, the user can also activate the functionalities of Sending of Indication

Objects on Bus Voltage Recovery, Heartbeat and Show Relay Switches Counter

Objects. These functions and their parameters will be explained in later sections of this

document.

Sending of Indication Objects (0 and 1) on Bus Voltage Recovery: this

parameter lets the integrator activate two new communication objects (“Reset

0” and “Reset 1”), which will be sent to the KNX bus with values “0” and “1”

MAXinBOX 24

http://www.zennio.com Technical Support: http://support.zennio.com

respectively whenever the device begins operation (for example, after a bus

power failure). It is possible to parameterise a certain delay to this sending (0

to 255 seconds).

Figure 3. Sending of Indication Objects on Bus Voltage Recovery.

Heartbeat (Periodical Alive Notification): incorporates a one-bit object to

the project (“[Heartbeat] Object to Send ‘1’”) that will be sent periodically

with a value of “1” to notify that the device is still working (still alive)..

Figure 4. Heartbeat (Periodical Alive Notification).

Note: The first sending after download or bus failure takes place with a delay

of up to 255 seconds, to prevent bus overload. The following sendings match

the period set.

Show Relay Switches Counter Objects: enables two communication

objects to keep track of the number of switches performed by each of the

relays ("[Relay X] Number of Switches") and the maximum number of

switches carried out in a minute ("[Relay X] Maximum Switches per

Minute").

MAXinBOX 24

http://www.zennio.com Technical Support: http://support.zennio.com

2.2 OUTPUTS

The MAXinBOX 24 actuator incorporates 24 relay outputs, which can be configured

as:

Individual binary outputs, which allows an independent control of loads.

Shutter channels, which allow controlling the motion of shutters or blinds.

Fan Coil modules, which allow the control of the fan and the valve of two-

pipe fan coil units.

In particular:

MAXinBOX 24: the 24 outputs are grouped into two-output channels, which

themselves are grouped into two-channel (or four-output) blocks. Therefore, it

is possible to configure up to 6 fan coil modules, or up to 12 shutter channels,

or up to 24 individual outputs.

For detailed information about the functionality and the configuration of the related

parameters, please refer to the following specific manuals, all of them available within

the MAXinBOX 24 product section at the Zennio website (www.zennio.com):

Individual outputs.

Shutter channels.

‘Relays’ Fan Coil. Note that MAXinBOX 24 is only compatible with two-pipe

fan coils. Therefore, any references to four-pipe fan coils do not apply to this

device.

MAXinBOX 24

http://www.zennio.com Technical Support: http://support.zennio.com

2.3 MANUAL CONTROL

MAXinBOX 24 allows manually switching the state of its output relays through the

respective pushbuttons on the top of the device. A specific pushbutton is therefore

available per output.

Manual operation can be done in two different ways, named as Test On mode (for

testing purposes during the configuration of the device) and Test Off mode (for a

normal use, anytime). Whether both, only one, or none of these modes should be

accessible needs to be parameterised in ETS. Moreover, it is possible to enable a

specific binary object for locking and unlocking the manual control in runtime.

Notes:

The Test Off mode will be active (unless it has been disabled by parameter)

after a download or a reset with no need of a specific activation –the

pushbuttons will respond to user presses from the start.

On the contrary, switching to the Test On mode (unless disabled by

parameter) needs to be done by long-pressing the Prog/Test button (for at

least three seconds), until the LED is no longer red and turns yellow. From

that moment, once the button is released, the LED light will remain green to

confirm that the device has switched from the Test Off mode to the Test On

mode. After that, an additional press will turn the LED yellow and then off,

once the button is released. This way, the device leaves the Test On mode.

Note that it will also leave this mode if a bus power failure takes place.

Test Off Mode

Under the Test Off Mode, the outputs can be controlled through both their

communication objects and the actual pushbuttons located on the top of the device.

When one of these buttons is pressed, the output will behave as if an order had been

received through the corresponding communication object, depending on whether the

output is configured as either an individual output, as a shutter channel or as a fan coil.

Individual output: asimple press (short or long) will make the output switch

its on-off state, which will be reported to the KNX bus through the

Inhaltsverzeichnis

Andere Zennio Controller Handbücher

Zennio

Zennio LUMENTO X4 Leitfaden

Zennio

Zennio MINiBOX 0-10V X3 Bedienungsanleitung

Zennio

Zennio ALLinBOX 1612 Leitfaden

Zennio

Zennio MAXinBOX Hospitality ZCL-HP126 Bedienungsanleitung

Zennio

Zennio FANinBOX 110V 1CH Leitfaden

Zennio

Zennio MAXinBOX SHUTTER 4CH Bedienungsanleitung

Zennio

Zennio FANinBOX 230V 1CH Leitfaden

Zennio

Zennio HeatingBOX 24V 4X Bedienungsanleitung

Zennio

Zennio MINiBOX 45 v3 Leitfaden

Zennio

Zennio ZN1CL-IRSC Bedienungsanleitung

Zennio

Zennio MINiBOX 45v2 Bedienungsanleitung

Zennio

Zennio MAXinBOX 66 Leitfaden

Zennio

Zennio Tecla 55 X Sign Bedienungsanleitung

Zennio

Zennio MAXinBOX FANCOIL 2CH2P Bedienungsanleitung

Zennio

Zennio MAXinBOX SHUTTER 8CH v3 Leitfaden

Zennio

Zennio inBOX 24 vT Bedienungsanleitung

Zennio

Zennio ZoningBOX 6 Bedienungsanleitung

Zennio

Zennio MAXinBOX 16 Plus Leitfaden

Zennio

Zennio ZCL-8HT230 Bedienungsanleitung

Zennio

Zennio MAXinBOX 66 Bedienungsanleitung

Zennio

Zennio MAXinBOX 24 Leitfaden

Zennio

Zennio HeatingBOX 230V 4X Leitfaden

Zennio

Zennio ZCL-MCC Bedienungsanleitung

Zennio

Zennio MAXinBOX 8 Plus Leitfaden

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung