Zephyr AK0710 Installationsanleitung

www.zephyronline.com

Use, Care and Installation Guide

Tempest I , II

Stainless Steel

Backsplash

AK0710 - 30”

AK0716 - 36”

AK0712 - 42”

AK0718 - 48”

FEB07.0201

Table of Contents

LIST OF MATERIALS —————————–- 2

SPECIFICATION ———————————— 3

INSTALLATION ————————————- 4,5

CLEANING AND

CONTACT INFORMATION ———————— 6

1

List of Materials

1 - Upper Section

1 - Lower Section

2 - Wire Racks

1 - Hardware Packet

2 - Retaining Clips

4 - Hinge Clips

6 - 7/16” Carriage Head Bolts

8 - 5/8” Philips Head Wood Screw

6 - Carriage Head Bolt Nuts

Note: If any parts are missing, please call

1-888-880-8368 for replacements.

2

Specifications

3

Installation

1. Mark a level line on the wall at 16” below bottom of hood.

2. Position the lower section of backsplash (flat part with flange on top) on the wall.

Center it side to side and mark the top and bottom holes. Remove the lower section from

the wall.

3. If installing onto drywall only and not onto studs, insert wall anchors (we recommend EZ

anchors) into the marked holes. If installing onto studs, attach screws without EZ anchors.

4. Attach lower section of backsplash to wall with screws provided.

5. Position upper section of backsplash by engaging its flange with the lower section. Push up

to fully engage flanges*, center it side to side and mark the location of the mounting holes.

Remove the upper section from drywall and install wall anchors into marked holes.

5b.If hood is already installed, attach wall anchors into the (3) holes from inside the hood at the

bottom. These are the holes which the upper section will line up with and mount to the wall.

6. Insert retaining clips and hinge clips to the upper section. The retaining clips go in the top

top two openings and the hinge clips go in the bottom four openings. (see diagram, page 4)

Fasten and tighten nuts to the clips on back of the upper section with the provided

hardware.

7. Attach upper section to wall with screws provided. If hood is already installed, Insert the top

2” lip of the upper section behind the bottom of the hood and line up the holes with the (3)

holes at the bottom of the hood. Insert screws into holes and fasten upper section to wall.

*note: in some installations, the flanges will not fully engage in the final install. This is fine

since the weight of the upper section will rest against the bottom section.

4

Installation

1. For the warming plate option; snap the wire shelves into hinge clips

on the backsplash as shown in the left side shelf diagram.

2. For the spice rack option; attach shelf to hinge clips, as

show in the right side shelf diagram, then rotate shelf upwards and

secure with retaining clip.

5

Cleaning and Contact Information

Cleaning of the backsplash should be done frequently to preserve the

life of the stainless steel. Cleaning should typically be done once or

twice a month depending on your cooking habits.

When cleaning, use a non abrasive cleaner, do not use “orange”

cleaner. Abrasive cleaners may scratch the surface and discolor the

stainless steel. To clean the wire racks, soak them in soapy water.

DO NOT place in a dishwasher as this may discolor the wire racks.

You may also polish the stainless steel by using stainless steel polish.

Make sure when polishing to go along with the grain of the backsplash.

Zephyr Corporation

395 Mendell Street

San Francisco, CA 94124

1-888-880-8368

6

Dieses Handbuch passt für folgende Modelle

3

Inhaltsverzeichnis

Andere Zephyr Dunstabzugshaube Handbücher

Zephyr

Zephyr AK7048BS Installationsanleitung

Zephyr

Zephyr elica Glide Installationsanleitung

Zephyr

Zephyr Tornado Glo Installationsanleitung

Zephyr

Zephyr Willow AK8800AG Technisches Handbuch

Zephyr

Zephyr brisas BML-E30BG Installationsanleitung

Zephyr

Zephyr Firenze ZFI-M90BS Installationsanleitung

Zephyr

Zephyr Gust AK7100AS Installationsanleitung

Zephyr

Zephyr AK9028AS Installationsanleitung

Zephyr

Zephyr ZML-M90BG Installationsanleitung

Zephyr

Zephyr Napoli ZNA-M90DS Installationsanleitung

Zephyr

Zephyr ZNA-M90BS Installationsanleitung

Zephyr

Zephyr Pisa ZPI-E30AG290 Installationsanleitung

Zephyr

Zephyr ACT Luce ZLU-E30CS Installationsanleitung

Zephyr

Zephyr Glide EGL-E30AS Installationsanleitung

Zephyr

Zephyr ALU-E43BSX Installationsanleitung

Zephyr

Zephyr VALINA ZVA-M60AS290 Bedienungsanleitung

Zephyr

Zephyr Ombra Installationsanleitung

Zephyr

Zephyr Tornado II Installationsanleitung

Zephyr

Zephyr ZPO-E30AS Bedienungsanleitung

Zephyr

Zephyr AK8000CS Installationsanleitung

Zephyr

Zephyr AK6500 series Use Installationsanleitung

Zephyr

Zephyr Twister Installationsanleitung

Zephyr

Zephyr ZAZ Series Installationsanleitung

Zephyr

Zephyr AK7000BS Installationsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

Küppersbusch

Küppersbusch DX ISLA Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch