Zhone BSX8000 Bedienungsanleitung

BSX8-A2-GZ40-20 June 2005 1

BSX8000-5 Broadband Services Switch

Installation Instructions

Document Number BSX8-A2-GZ40-20

June 2005

Contents

Software and Firmware License Agreement ...................................................... 1

Product Documentation Online .......................................................................... 3

Release Notes ................................................................................................... 3

BSX8000-5 Overview ........................................................................................ 3

Unpacking and Inspecting the Equipment ......................................................... 4

Installing a Micro Interface Module (MIM) in the BSX8000-5 ............................ 4

Installing the BSX8000-5 in a BLC .................................................................... 5

Connect the MIM to the Network ....................................................................... 5

BLC Management .............................................................................................. 6

Web Interface (NMS) ......................................................................................... 6

Command Line Interface (CLI) .......................................................................... 10

LED Indicators ................................................................................................... 13

10/100/1000BaseT Connectors ......................................................................... 14

DB9 to RJ45 Adapter Pinouts ............................................................................ 14

Regulatory Compliance for Class A Equipment ................................................. 15

Warranty, Sales, Service, and Training Information ........................................... 15

Software and Firmware License Agreement

The terms and conditions of this License Agreement (the “Agreement”) will apply to the

software and/or firmware (individually or collectively the “Software”) incorporated into the

Paradyne product (the “Product”) purchased by you and any derivatives obtained from the

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS TERMS,

YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED INTO THE

PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU SHOW YOUR

ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS

LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS

ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE

LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE

LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU

WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT

PURCHASED BY YOU.

2June 2005 BSX8-A2-GZ40-20

Software, including any copy of either. If you have executed a separate written agreement

covering the Software supplied to you under this purchase, such separate written

agreement shall govern.

Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to accept a

personal, non-transferable, non-exclusive, right (without the right to sublicense) to use the

Software, solely as it is intended and solely as incorporated in the Product purchased from

Paradyne or its authorized distributor or reseller under the following terms and conditions:

1. Ownership: The Software is the sole property of Paradyne and/or its licensors. The

Licensee acquires no title, right or interest in the Software other than the license

granted under this Agreement.

2. Licensee shall not use the Software in any country other than the country in which the

Product was rightfully purchased except upon prior written notice to Paradyne and an

agreement in writing to additional terms.

3. The Licensee shall not reverse engineer, decompile or disassemble the Software in

whole or in part.

4. The Licensee shall not copy the Software except for a single archival copy.

5. Except for the Product warranty contained in the manual, the Software is provided “AS

IS” and in its present state and condition and Paradyne makes no other warranty

whatsoever with respect to the Product purchased by you. THIS AGREEMENT

EXPRESSLY EXCLUDES ALL OTHER WARRANTIES, WHETHER EXPRESS OR

IMPLIED, OR ORAL OR WRITTEN, INCLUDING WITHOUT LIMITATION:

a. Any warranty that the Software is error-free, will operate uninterrupted in your

operating environment, or is compatible with any equipment or software

configurations; and

b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE AND NON-INFRINGEMENT.

Some states or other jurisdictions do not allow the exclusion of implied warranties on

limitations on how long an implied warranty lasts, so the above limitations may not

apply to you. This warranty gives you specific legal rights, and you may also have other

rights which vary from one state or jurisdiction to another.

6. In no event will Paradyne be liable to Licensee for any consequential, incidental,

punitive or special damages, including any lost profits or lost savings, loss of business

information or business interruption or other pecuniary loss arising out of the use or

inability to use the Software, whether based on contract, tort, warranty or other legal or

equitable grounds, even if Paradyne has been advised of the possibility of such

damages, or for any claim by any third party.

7. The rights granted under this Agreement may not be assigned, sublicensed or

otherwise transferred by the Licensee to any third party without the prior written

consent of Paradyne.

8. This Agreement and the license granted under this Agreement shall be terminated in

the event of breach by the Licensee of any provisions of this Agreement.

9. Upon such termination, the Licensee shall refrain from any further use of the Software

and destroy the original and all copies of the Software in the possession of Licensee

together with all documentation and related materials.

This Agreement shall be governed by the laws of the State of Florida, without regard to its

provisions concerning conflicts of laws.

BSX8-A2-GZ40-20 June 2005 3

BSX8000-5 Overview

The BSX8000-5 Broadband Services Switch provides multi-gigabit Ethernet uplink

support capability, full-nonblocking switching throughput, and enhanced

management functionality for the 4000E and 12000E Broadband Loop Carriers

(BLCs).

The BSX8000-5 supports four fixed 10/100/1000 RJ45 Ethernet interfaces and

one MIM (Micro Interface Module) slot. Multiple MIM varieties are supported.

The BSX8000-5 delivers a full 1 Gbps full duplex

backplane connection to each access module in the

BLC. This ensures that the aggregate access bandwidth

cannot exceed the backplane speed of the chassis.

When two BSX8000 modules are used in the 12000E,

the backplane speed is doubled, providing a 2 Gbps

connection to each access module.

The BSX8000-5 supports the following access modules:

AAM8000-24

AIM24000-48

EIM2000-12

EIM2000-24

SIM2000-24

TIM1500-12

TIM1500-24

The BSX8000-5 supports 576 DSL ports.

Product Documentation Online

Complete documentation for Paradyne products is available at

www.paradyne.com. Select Support →Technical Manuals.

To order a paper copy of a Paradyne document, or to speak with a sales

representative, please call 1-727-530-2000.

Release Notes

Release notes for this product are available in the subscriber firmware area of

www.paradyne.com. Select Support →Subscriber Firmware.

Always review the relevant release notes before installing a new card.

4June 2005 BSX8-A2-GZ40-20

Unpacking and Inspecting the Equipment

HANDLING PRECAUTIONS FOR

STATIC-SENSITIVE DEVICES

This product is designed to protect sensitive components from damage

due to electrostatic discharge (ESD) during normal operation. When

performing installation procedures, however, take proper static control

precautions to prevent damage to equipment. If you are not sure of the

proper static control precautions, contact your nearest sales or service

representative.

If there is any visible damage, do not attempt to connect the device. Contact your

sales or support representative

Installing a Micro Interface Module (MIM) in the BSX8000-5

A MIM provides the upstream network connection for the BLC. Any of Paradyne's

available MIM models may be installed on the BSX8000-5 uplink module.

Procedure

1. Remove the cover plate from the MIM port.

CAUTION: Cover plates should be stored for possible future use. If a MIM is

removed from a BSX8000-5, it must be replaced with either another MIM or a

cover plate. Do not operate a BSX8000-5 with an open MIM port.

2. Carefully slide the faceplate of the MIM into the BSX8000-5 uplink module

faceplate. Ensure that the mounting holes on the MIM are lined up with the

BSX8000-5 uplink module.

3. Secure the MIM circuit board to the BSX8000-5 uplink module with the two

thumbscrews.

BSX8-A2-GZ40-20 June 2005 5

Installing the BSX8000-5 in a BLC

The 12000E is a 14-slot Broadband Loop Carrier (BLC). Slots 1–12 are reserved

for access modules (such as the AIM24000-48) and slots U1 and U2 are reserved

for uplink modules. Although not required for operational purposes, if redundancy

is desired, two BSX8000-5 modules may be installed in the 12000E, in slots U1

and U2. (Note: For redundancy, the two uplink modules in the chassis must be

identical models.)

The 4000E is a five-slot BLC. Slots 1–4 are reserved for access modules and slot

U1 is reserved for a single uplink module.

Procedure

1. Align the BSX8000-5 uplink module with the slot module guides of the chosen

slot for installation (either slot U1 or U2 on the 12000E or slot U1 on the

4000E).

2. Slide the BSX8000-5 uplink module into the chassis. Do not use excessive

force.

3. Tighten the fastening screws on the BSX8000-5 uplink module faceplate.

4. Verify that the PWR (Power) LED on the BSX8000-5 faceplate is illuminated.

Connect the MIM to the Network

Connect to the core network by using one of the fixed GigE interfaces or by using

an interface from the added MIM. See 10/100/1000BaseT Connectors on page 14.

MIM-10/100

Plug your Ethernet cable into the RJ45 Ethernet port on the MIM-10/100 faceplate.

The MIM-10/100 connects to a router or a PC with a straight-through cable and to

a hub or a switch with a crossover cable.

Verify the connection: solid illumination of the Lnk (link) LED on the MIM-10/100

faceplate indicates an Ethernet uplink connection has been established. The

MIM-10/100 Ethernet port is 10/100 auto-negotiating.

NOTE: Configure the remote device with which you are connecting to

auto-negotiate (if applicable) prior to establishing your Ethernet connection.

MIM100F

Plug your Ethernet Fiber Optic Cable into the port on the MIM100F faceplate.

MIM-2000F

The MIM-2000F is a two-port fiber gigabit Ethernet interface, which connects to

the Fast Ethernet Bus of the BLC. This will function but is not recommended for

use with the BSX8000-5 Uplink Interface.

6June 2005 BSX8-A2-GZ40-20

MIM-4000F

The MIM-4000F is a four-port fiber gigabit Ethernet interface connecting directly to

the gigabit Ethernet switch in the BSX8000-5 uplink module.

MIM-2E1 or MIM-4E1

Plug your E1 cable into one of the RJ45 E1 ports on the MIM faceplate. The

MIM-2E1 or MIM-4E1 connects to an E1 network extender provider unit, or an

interface module in another BLC, via a standard E1 line.

Verify the connection: the Lnk (link) LED on the MIM faceplate flashes green to

indicate a network connection has been established.

MIM-2T1 or MIM-4T1

Plug your T1 cable into one of the RJ45 T1 ports on the MIM faceplate. The

MIM-2T1 or MIM-4T1 connects to a T1 network extender provider unit, or an

interface module in another BLC, via a standard T1 line.

Verify the connection: the Lnk (link) LED on the MIM faceplate flashes green to

indicate a network connection has been established.

BLC Management

The BSX8000-5 uplink module provides BLC management capability via the

Command Line Interface (CLI), Simple Network Management Protocol (SNMP),

and the web-based Network Management System (NMS).

Web Interface (NMS)

The following are required for use of the NMS:

Web Browser – Required for running NMS. Compatible web browsers

include, but are not limited to, Microsoft Internet Explorer (version 6.0 or

higher) and Netscape Navigator (version 6.0 or higher). NMS is optimized for

use with Internet Explorer.

Use your browser's default settings when running NMS. JavaScript must be

enabled.

Screen Resolution – 1024 x 768 pixels is the minimum resolution required for

all NMS views to fit within the dimensions of most monitors and laptops. Lower

screen resolutions (such as 800 x 600 pixels) may cause NMS screens to

exceed the width or height of the screen. To verify screen resolution on a

Windows system:

— Right click on your desktop

— Select Properties

— Click the Settings tab

— Adjust the Screen Resolution as needed

BSX8-A2-GZ40-20 June 2005 7

Configuring Your Windows PC to Communicate with NMS

To communicate with NMS, your PC’s Ethernet interface must be on the same

subnet as the BSX8000-5. For example, to configure the IP address under

Windows XP:

Procedure

1. In the Windows task bar, click on the Start button, and then click on Control

Panel.

2. Double-click on the Network Connections icon.

3. In the LAN or High-Speed Internet window, right-click on the icon

corresponding to your network interface card (NIC) and select Properties.

(Often this icon is labeled Local Area Connection.) The Local Area Connection

dialog box is displayed with a list of currently installed network items.

4. Ensure that the check box to the left of the item labeled Internet Protocol

(TCP/IP) is checked, and click on Properties.

5. Write down the current IP Address and Subnet Mask in the Internet Protocol

(TCP/IP) Properties dialog box. When you are done using NMS, you will need

to reconfigure your PC with these values.

6. In the Internet Protocol (TCP/IP) Properties dialog box, click in the radio button

labeled “Use the following IP address” and type 192.168.254.x (where x is any

number between 3 and 250, inclusive) in the IP Address field.

7. Type 255.255.255.0 in the Subnet Mask field.

8. Click on OK twice to confirm your changes, and close the Control Panel.

9. Start your web browser. Type the default IP address into the Address field and

press Enter. The default IP address of a BSX8000-5 in Slot 13 of a 12000E

BLC or Slot 5 of a 4000E BLC is 192.168.254.252. The default IP address of a

BSX8000-5 in Slot 14 of a 12000E BLC is 192.168.254.253.

The web server opening screen appears.

10. Click on >> Next >>. The login dialog box appears. Log in using:

Username: superuser

Password: Password

8June 2005 BSX8-A2-GZ40-20

The NMS home page appears.

BSX8-A2-GZ40-20 June 2005 9

NMS Management Configuration

Use the Management Configuration screen to set the unit’s IP address and other

management parameters.

Procedure

To configure management parameters:

1. From the home screen, click on the Management Config button. The

Management Configuration screen appears.

2. Select or enter the following parameters:

Parameter Description

IP Address Specify the management IP address for the DSLAM.

Subnet Mask Specify the subnet mask for the IP address.

Gateway Specify the first-hop gateway address.

EtherType Select the type of packets supported by your router.

This is used only for backbone VLAN (Q in Q) traffic.

Inband MGMT Check this box if you will use inband management

(that is, you will allow the device to be contacted by

ports other than the MGMT port)..

VLAN Id Specify a VLAN identifier for inband management.

Priority Specify a priority (0–7) for inband management traffic.

10 June 2005 BSX8-A2-GZ40-20

3. Click on Submit.

Command Line Interface (CLI)

CLI System Requirements

Straight-Through RJ45 to RJ45 Ethernet Cable – Required for establishing

a direct connection from the COM port to a DB9 adapter.

DB9 Female to RJ45 Male Adapter – Required for conversion of your PC's

RS232 serial port for use with the RJ45 to RJ45 Ethernet cable.

Terminal Emulation Program – Required for running the CLI over a direct

connection. The program must emulate a VT100 terminal.

Telnet Client – Required for remote management with the CLI. Microsoft

Windows Operating Systems (98, 2000, NT, and XP) include a Telnet client

which is executed using the Windows command prompt (cmd.exe). If you are

using an operating system other than Windows, you may need to install a

Telnet client.

Flood Configuration Flood refers to the method in which interface modules

handle unknown unicasts, unknown broadcasts, and

unknown multicasts for each port.

Uplink – Any traffic with VLAN IDs that match a

VLAN ID that has been configured to Uplink flood

(default) will be allowed to flow from DSL ports to

uplinks only (not DSL port to DSL port).

VLAN – Any traffic with VLAN IDs that match a

VLAN ID that has been configured to VLAN flood

will be allowed to flow from DSL port to uplinks and

DSL port to DSL port.

Flood Membership

Configuration

Specify the VLAN membership of the uplink ports

(four fixed ports and any MIM ports).

By default all uplinks are members of all VLANs.

However you can change it such that an uplink port is

a member of only a certain set of VLAN IDs. In this

case any ingress or egress traffic on an uplink port

with a VLAN ID that the uplink port is not a member of,

will be dropped.

Parameter Description

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Zhone Schalten Handbücher

Zhone

Zhone 4929-A1-530 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch