ZiLOG ZMOTION Bedienungsanleitung

www.zilog.com

Introduction

This Quick Start Guide acquaints users with Zilog’s ZMOTION Intrusion Detection

Development Kit (part number ZMOTIONS200ZCOG) and provides instructions for set-

ting up and using the Kit to demonstrate its basic operation. The following topics are cov-

ered:

•Getting Started: the quickest way to get the board up and running; see page 3

•Installing the Lens: see page 5

Kit Contents

• ZMOTION Intrusion Detection Development Board

• USB SmartCable Debugger

• 1.2" focal flat lens holder

• Three 1.2" focal flat lenses

– ZWA12GI12V4

– ZLR12GI12V3

– ZVB12GIV1

• Mini-USB serial cable

• Wall mount power supply

• Mounting hardware

Figure 1 shows the components of the Intrusion Detection Development Kit and Figure 2

displays the three lenses.

ZMOTION®Intrusion

Detection Development Kit

Quick Start Guide QS007802-1014

ZMOTION®Intrusion Detection Development Kit

Quick Start Guide

QS007802-1014 Page 2 of 10

Figure 1. ZMOTION Intrusion Detection Development Kit Components

1.2" Lens Holder

ZMOTION®Intrusion Detection Development Kit

Quick Start Guide

QS007802-1014 Page 3 of 10

Getting Started

The

ZMOTION Intrusion Detection Development Kit

contains several lens options. To

provide a quick method of getting the Kit up and running, the ZMOTION MCU is initially

programmed with a

ZMOTION_Intrusion_Demo

project using the RE200B-P pyroelectric

sensor and the ZWA12GI12V4 lens. By installing the lens and then applying power, the

basic operation of the Kit can be observed.

To get started with the Kit, observe the following brief procedure.

1. Install the ZWA12GI12V4 lens as described on page 5.

2. Insert the power supply output connector into the Mini-USB Plug P1 on the

ZMOTION

Development Board and insert the other end into the wall outlet. Move SW1 on the

board up to the ON position.

Figure 2. The Three Lenses contained in this Development Kit

ZMOTION®Intrusion Detection Development Kit

Quick Start Guide

QS007802-1014 Page 4 of 10

Use the power supply provided with the Kit.

3. The Blue power LED will illuminate and the Red LED will flash 1 second on and one

second off until the pyroelectric sensor stabilizes –a period of approximately 10 to 60

seconds. After the pyroelectric sensor has stabilized, the Red LED turns OFF and turns

ON again only when motion is detected.

4. To test this procedure, wave your hand over the lens and notice the LED turning ON

for approximately 1 second.

To learn more about the operation of the Kit, including how to use the additional features

of the preloaded sample project and how to download and modify other ZMOTION proj-

ects, refer to the ZMOTION Intrusion Detection Kit User Manual (UM0233), available

from the Zilog website.

Downloading ZMOTION Software and Documentation

ZMOTION software and documentation are available as a downloadable file from the

Zilog Store. Observe the following steps to install this software.

1. In a web browser, visit zilog.com/store. At the top left, under Categories, click

Downloadable Software to present a list of the available software in the Zilog Store.

In this list, click ZMOTIONS200ZCOG Software and Documentation; the Product ID

for this software is SD00030.On the Product Details page, click the Add to Cart button

and complete the Checkout process to download the ZMOTION Software and

Documentationfiles toyourhard drive.(Ifyou area first-time visitor to the Zilog Store,

you will be required to register before downloading this software).

2. When the download is complete, unzip the file to your hard drive, double-click to

launch the ZMOTIONS200ZCOG_<version>.exe installation file, and follow the on-

screen instructions.

3. When the installation is complete, the user manual can be viewed in the following path

when using the default installation directory: 

C:\Program Files (x86)\ZiLOG\ZMOTIONS200ZCOG_<version>\ZMOTION

Product Documentation

Note:

ZMOTION®Intrusion Detection Development Kit

Quick Start Guide

QS007802-1014 Page 5 of 10

Installing the Lens

When mounting the ZMOTION Development Board vertically, special con-

sideration should be taken regarding the height, angle and level plane of the

board. Be sure to follow the lens manufacturer’s recommended height and

mounting angle requirements to ensure optimal performance.

Flat Lens Holder

The flat lens holder, shown in Figure 3, is a two-piece assembly that provides a 1.2" focal

length mounting. Figure 4 shows the detail of the ZWA12GI12V4 lens, with its correct

orientation.

Figure 3. Flat 1.2"Lens Cap (Top) and Lens Base (Bottom)

Note:

ZMOTION®Intrusion Detection Development Kit

Quick Start Guide

QS007802-1014 Page 6 of 10

To assemble this flat lens and holder, observe the following brief procedure.

1. Place the lens into the inside of the cap, ensuring that the grooves of the lens are facing

inward.

2. Place the cap over the base, ensuring that the top of the lens is toward the arrow on the

base. Use the provided ¾" machine screws (2) with a nut to secure the cap in place, as

shown in Figure 5.

Figure 4. Flat Lens: ZWA12GI12V4

ZMOTION®Intrusion Detection Development Kit

Quick Start Guide

QS007802-1014 Page 7 of 10

3. Place the lens and lens holder assembly onto the ZMOTION Development Board with

the arrow on the lens holder pointing up, as shown in Figure 5; use the Primary Place-

ment position labeled on the circuit board for the ZWA12GI12V4 lens. The four screw

holes in the circuit board should line up with the four upper mounting holes in the lens

holder.

4. Fasten each of the four (4) provided ⅜" machine screws with a nut to secure the lens

holder in place. Figure 6 shows an example of the top of the lens holder installed on the

ZMOTION Development Board.

Figure 5. Assembled Flat 1.2" Lens Holder and Flat Lens

ZMOTION®Intrusion Detection Development Kit

Quick Start Guide

QS007802-1014 Page 8 of 10

Installing ZDSII and the USB SmartCable

To learn more about installing ZDSII and the USB SmartCable, installing the FTDI driver

for the serial cable, downloading and running the sample project, and making changes to

the sample project, refer to the ZMOTION Intrusion Detection User Manual (UM0233),

available on zilog.com.

Figure 6. Top of Lens Holder on the ZMOTION Development Board

ZMOTION®Intrusion Detection Development Kit

Quick Start Guide

QS007802-1014 Page 9 of 10

References

Refer to the documentation in Table 1 for additional information about Zilog’s ZMOTION

products.

Table 1. ZMOTION Documentation

Document

Number Description

PS0288 ZMOTION Intrusion Detection Product Specification

PB0230 ZMOTION Intrusion Detection Product Brief

UM0233 ZMOTION Intrusion Detection Development Kit User Manual

WP0018 ZMOTION Lens and Pyro Configuration Guide

PS0228 Z8 Encore! XP F082A Series Product Specification

PS0286 ZMOTION Lens Product Specification

PS0336 ZMOTION Pyroelectric Sensor Product Specification

RD0001 ZMOTION Intrusion Reference Design

WP0017 ZMOTION –A New PIR Motion Detection Architecture

ZMOTION®Intrusion Detection Development Kit

Quick Start Guide

QS007802-1014 Page 10 of 10

DO NOT USE IN LIFE SUPPORT SYSTEMS.

LIFE SUPPORT POLICY

ZILOG’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPO-

NENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS

PRIOR WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF

ZILOG CORPORATION.

As used herein

Life support devices or systems are devices which (a) are intended for surgical implant

into the body, or (b) support or sustain life and whose failure to perform when properly

used in accordance with instructions for use provided in the labeling can be reasonably

expected to result in a significant injury to the user. A critical component is any compo-

nent in a life support device or system whose failure to perform can be reasonably

expected to cause the failure of the life support device or system or to affect its safety or

effectiveness.

Document Disclaimer

devices, applications, or technology described is intended to suggest possible uses and

may be superseded. ZILOG, INC. DOES NOT ASSUME LIABILITY FOR OR PRO-

VIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION, DEVICES,

OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO DOES NOT

ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT

RELATED IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECH-

NOLOGY DESCRIBED HEREIN OR OTHERWISE. The information contained within

this document has been verified according to the general principles of electrical and

mechanical engineering.

ZMOTION is a registered trademark of Zilog, Inc. All other product or service names are

the property of their respective owners.

Warning:

Andere Handbücher für ZMOTION

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ZiLOG Sicherheitssensor Handbücher

ZiLOG

ZiLOG ZMOTION Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung