Zline KECOM-RD-48 Bedienungsanleitung
Wall Range Hood Installation
4
Installation
Tutorial Video
*Note: Wall range hoods with single motors will come with a square to 6˝ round transition piece
and will include a back dra damper. e ducting with these range hoods is 6˝.
Dual motor wall hoods will come with a square to 8˝ round transition piece without a back dra
damper. e ducting with these range hoods is 8˝.
*Use rigid ducting wherever possible. Try and minimize the use of elbows. More elbows and lon-
ger runs create higher static pressure. e hood comes with a grounded three prong plug that can
either be direct wired or plugged into a 20 amp. circuit.
A
E
B
F
6
D
C
B C E F
D
A
1. Main Hood With All Lights and
Button Banks Pres-installed
2. Adjustable Stainless Chimney Cover
3. Transition Piece (For 6˝ or 8˝)
4. Bae Filters
5. Flexible Duct (For 6˝ or 8˝)
6. Packet of Screws and Anchors
7. Top Mounting Bracket
8. Grease Cup
Parts Supplied:
Please unpack your range hood when it is delivered
and inspect to ensure all parts are included.
5
Wall Range Hood Installation
1
2
3
4
Find the center of the wall where you
are installing the hood. Make sure
there is sucient bracing to hold the
weight of the hood. Mark your center
line and measure out from the center
to nd your two mounting points.
Make sure your mounting points are
level when you mark them. It is rec-
ommended to install the hood direct-
ly into wood supports. (Figure 1)
Mark the mounting points and install
the two mounting screws provided
leaving the heads out ¼˝to mount the
hood. (Figure 1)
Mount the main body of the hood to
the two screws and screw into place.
(Figure 2)
Mount the top chimney mounting
bracket centering it above the hood.
(Figure 3)
Figure 1
Figure 2
Figure 3
*e recommended height to install your hood is 30˝minimum and 36˝maximum
above the cooktop.
*For Outdoor (304 Series) hood installation, the unit must be installed at a minimum
of 36˝above the grill.
6
Wall Range Hood Installation
Figure 5
Figure 4
Figure 6
7
6Make your electrical and ducting
connections. Try and minimize the
use of elbows. More elbows and lon-
ger runs create higher static pressure.
e hood comes with a grounded
three prong plug that can either be
direct wire or plugged into a 20amp.
circuit. (Figure 5)
5Install the transition piece securing it
with screws provided. (Figure 4)
Connect the ducting to the transition
piece using ring to hold into place.
Attach ducting to the range hood.
(Figure 6)
7
Wall Range Hood Installation
8
9
Install the two part chimneys on top
of the hood. Slide the inside section
up until the vertical vent slots are vis-
ible, attach top portion to mounting
bracket with screws. Secure lower
chimney portion to the hood with
screws provided. (Figure 7)
Install plastic drip cup by sliding into
brackets located at the bottom of the
motor. Install ◆bae channel and baf-
e lters. (Figure 8)
◆Not all models include bae channels.
*Before installing bae lters, make sure
that you insert the grease cup under the
motor blower.
Figure 7
Figure 8
8
Wall Range Hood Installation
25
Remote Blower Installation Options
1
2
3
4
Run duct work into the area that you will
install the remote from your range hood.
Fasten ducting to the range hood using
a hose clamp and silver/duct tape.
Use the least amount of elbows
as possible.
Mount the remote blower to
studs only.
When installing your new remote blower type range hood, follow the instructions for the type
of hood you are installing. If you are installing a wall, Island, under cabinet or insert hood
then you will follow those instructions. is portion of the manual will explain how to install
the remote blower for your range hood.
Remote Range Hood
Connections
Remote Blower Installation:
Installation
Tutorial Video
26
Remote Blower Installation Options
5
6
7
8
Run electrical cord (Provided) back
to the range hood (up to 26).
Install a regular outlet with a 20
amp circuit.
e hood comes with a grounded
3 prong grounded plug.
Run duct work to the outside of
the house and add a back dra
damper outside.
NOTE: e remote blower must be kept inside
the home, attic or crawl space etc. Never try to
install a remote blower outside of the home.
Remote Blower
with Brackets
e Remote Blower is designed for our Remote Range Hoods.
is unit is installed remotely in the interior of your home.
is provides venting, but with reduced noise.
T85 Remote Blower—Single Motor
(This Blower must be used with Remote Blower Hood)
Airow 280 / 400 / 580 / 900 (CFM)
Noise Level: 1.2 / 2.6 / 4.2 / 6.5 (Sones)
Dimensions: 26.14 x 14.6 x 13
T95 Remote Blower—Dual Motor
(This Blower must be used with Remote Blower Hood)
Airow 280 / 460 / 670 / 1200 (CFM)
Noise Level: 1.2 / 2.8 / 5.0 / 7.0 (Sones)
Dimensions: 26.14 x 14.6 x 13
27
Remote Blower Installation Options
e Remote Blower is designed for our Remote Range Hoods.
is unit is installed remotely in the interior of your home.
is provides venting, but with reduced noise.
T85 Remote Blower—Single Motor
(This Blower must be used with Remote Blower Hood)
Airow 280 / 400 / 580 / 900 (CFM)
Noise Level: 1.2 / 2.6 / 4.2 / 6.5 (Sones)
Dimensions: 26.14 x 14.6 x 13
T95 Remote Blower—Dual Motor
(This Blower must be used with Remote Blower Hood)
Airow 280 / 460 / 670 / 1200 (CFM)
Noise Level: 1.2 / 2.8 / 5.0 / 7.0 (Sones)
Dimensions: 26.14 x 14.6 x 13
28
Remote Blower Installation Options
Inhaltsverzeichnis
Andere Zline Dunstabzugshaube Handbücher
Zline
Zline 521 Montageanleitung
Zline
Zline 520 Fehlerbehebungshandbuch
Zline
Zline ATTAINABLE LUXURY CROWNSOUND Bedienungsanleitung
Zline
Zline 515 Montageanleitung
Zline
Zline ISLAND Bedienungsanleitung
Zline
Zline 432-30 Montageanleitung
Zline
Zline Attainable Luxury Alpine Series Montageanleitung
Zline
Zline RK62342 Montageanleitung
Zline
Zline Attainable Luxury 24" Montageanleitung
Zline
Zline 568 Montageanleitung
