Zodiac T5 Duo Suction Bedienungsanleitung

1/LIST OF PARTS 15

ADVICE 15

2/FITTING THE HOSE 16

3/CONNECTING 17

4/FLOW TEST 19

5/HOSE AND CLEANER ASSEMBLY 20

6/TROUBLESHOOTING 21

7/CLEANING, REPLACING THE DIAPHRAGM 22

8/WARRANTY 24

Dear customer,

Congratulations on your purchase of the ZODIAC T5 Duo

Suction cleaner. We would like to thank you for your custom.

Your appliance has been designed, manufactured and

checked with the greatest care to ensure you are completely

satisfied with the product.

Before using the appliance read this manual carefully.

It contains all the information needed in order to get

the most from your pool cleaner in complete safety.

For any further information your retailer, a pool professional,

will be able to advise you on how to use and maintain

your pool cleaner.

They will be able to supply spare parts and will provide

qualified After Sales service.

Contents

1 4

1/List of parts

1 5

Below is the list of parts shipped in the box needed to install

your T5 Duo:

Complete head

Complete disk

Quick connector

Deflector wheel (used if the cleaner jams

on obstacles, ladders, steps,...)

Set of 12 Twist Lock 1 metre hose sections

1 hose counter-weight

1 automatic flow regulation valve

1 flow tester

1 cone adapter

During the season we recommend you leave your T5 Duo

in the pool and remove it when you do shock treatments.

If you wish to remove it while bathing, remove the hose,

but do not roll it up.

Never expose the hose to direct sunlight.

When the season is over, we recommend that you rinse the hose

sections in clear water and you store them in a dry place.

ADVICE

REF. NAME QUANTITY

1Complete Head 1

2Complete disk 1

3Quick connector 1

4Deflector wheel 1

5Set of 12 Twist Lock 1 metre hose sections 12

6Hose counter-weight 1

7Automatic flow regulation valve 1

8Flow tester 1

9Cone adapter 1

6 5 4 3 2 1 0

01 2 3 4 5 6

The hose for your T5 Duo is composed of 12 x 1 m sections.

•The ideal hose length for your pool corresponds to one 1 m hose

section plus the greatest distance between the Connection point

(suction point or skimmer) and the furthest point in your pool

(Figure 1).

Ex: if the greatest distance between the suction point or skimmer

and the furthest point equals 10 metres, you will need 11 sections

of 1 metre.

•Once you have calculated the total length, assemble your

hose by inserting the 1 m sections into each other, male end

connected to female end. In order the join them correctly,

give the hose a quarter turn so as to position the latch in

the notch.

You do not need to fit the tab in the last housing when using

the cleaner at first (Figure 2).

2/Fitting the hose

1 6

Figure 2 Lock latch

Figure 1

Greatest

distance

•Orient your pool inlet jets downward.

•Close the main drain of your pool.

•Activate the pool pump.

•Fill the T5 Duo hose with water using the flow generated

by the return fitting and maintain the hose underwater for

the remained of the operations (Figure 3). The hoses must be

emptied of all the air they contain in order for the cleaner to

operate correctly. Once all the air has been removed, the robot

will sink to the bottom of the pool.

IMPORTANT NOTE:

You can connect the T5 Duo hose to the suction point or to one

of the skimmers in your pool.

It is preferable to use a suction point situated at mid-distance

of the main length of your pool.

CONNECTING TO THE VACUUM POINT OR TO THE SKIMMER

IMPORTANT: When connecting the last elements (last section

of hose, automatic flow control valve, leaf trap*) ensure that

these remain underwater so that there is absolutely no risk of air

entering the system and draining the pump.

•Install the automatic flow control valve on the suction point using

the weir adaptor.

IMPORTANT:

The automatic flow adjustment valve is pre-set in the factory to

number 3, the most suitable position for European pools.

For an optimal performance from your cleaner, we recommend

that you do not move the valve from this position.

Secondly, always check that the valve's dark grey flap is not held

in the open position by the red lever – otherwise your cleaner

cannot function (Figure 4).

•Connect the first 1 m section to the flow control valve, after

filling it with water to remove the air.

•Connect the leaf trap* to the other end of the hose section after

it too has been filled with water.

IMPORTANT: Make sure that the arrows on the automatic flow

regulator valve and on the leaves basket* point toward the suction

point and not toward the robot.

3/Connecting

1 7

Figure 3

Figure 4

* optional, not sold with this product.

Connect the male part of the hose adaptor to the leaf trap*.

Check that there is no air in the hose assembly, then connect it to

the vacuum point by joining the last hose section to the female

part of the hose adaptor (Figure 5).

Connection to the vacuum point with leaf trap*

Connection to the skimmer with leaf trap*

Check that there is no air in the hose

assembly before connecting it to the

skimmer.

Figure 7

Example with the connection to

the vaccuum point

1 8

Figure 5

Figure 6

* optional, not sold with this product.

Figure 7

optional

You can always check the flow rate, particularly if you have doubts

about the suction power of your pump.

NB: all these operations must be carried out under water so that

the pump does not take in air.

•Remove your T5 Duo from its hose, hold down the quick connector

and connect it to the flow tester (Figure 8).

Note the zone indicated on the tester (Figures 13 to 15)

“Ideal”: The red indicator is on 3.

The flow is perfect to operate your T5 Duo. Remove the tester and

reconnect the cleaner to the hose.

“Minimum”: The red indicator is below 3.

Increase the flow by closing the skimmer valve if the cleaner is

connected to the suction point or by closing the suction outlet

valve if the cleaner is connected to the skimmer, until the indicator

on the tester is in the ideal zone. Remove the tester and reconnect

the device to the hose.

“Maximum”: The red indicator is above 3.

Reduce the flow by opening the skimmer valve if your cleaner is

connected to the suction point or by opening the suction outlet

valve if your cleaner is connected to the skimmer, until the

indicator on the tester is in the ideal zone. Remove the tester

and reconnect the cleaner to the hose.

4/Flow test

1 9

6 5 43 2 1 0

0 1 2 3 45 6

Figure 9

6 5 4 3 2 1 0

0 1 2 3 4 5 6

Figure 10

6 5 4 3 2 1 0

0 1 2 3 4 5 6

Figure 11

Figure 8

•Immerse the hose and the cleaner and assemble the elements

underwater.

•Fit the assembled hose (see paragraph 2 page 16 : fitting

the hose) with the quick connection fitting (Figure 12).

To assemble them correctly make a quarter turn and position

the tabs in one of the slots. You do not need to fit the tab in the

last housing when using the cleaner at first.

•If needed; if you have ladders or areas that might jam

your cleaner, clip the non blocking wheel to the end of the hose

(Figure 12).

•Then clip the assembly to the cleaner nozzle (Figure 13).

•A counter-weight is supplied to be used when the T5 Duo

tends to rise from the bottom of the pool (Figure 14).

Fit the counterweight to the end of the first hose section at about

1 metre from the appliance (Figure 15) then make sure that

the disk remains on the bottom of the pool when the appliance

is operating.

5/Hose and cleaner assembly

2 0

Figure 12

Figure 13

Figure 15

Figure 14

incorrect incorrectcorrect

•Control the flow using the flow tester.

If the flow is insufficient:

•Check that the valve of the main drain is closed.

•Check that the pump pre filter and basket are clean.

•Check that the hose and automatic adjustment valve are

correctly connected.

IMPORTANT:

Always check that the dark grey flap gate on the valve is not held

in the open position by the red lever – otherwise your pool cleaner

cannot operate.

If the water flow is correct:

•Check that the cleaner suction inlet is not clogged up with debris.

•Is the T5 Duo Diaphragm damaged?

(see pages 22 and 23)

•In order to ensure complete cleaning of the pool, the total time

may be split into periods. For example, 6-hour filtration performed

as 3 times 2 hours will provide better coverage than a single

6-hour filtration.

•Is your hose long enough: add hose sections if necessary.

•Have you oriented all inlet jets downwards?

•Is the hose in perfect condition?

•Check the position of the float on the hose (see figure 14 page 20).

•Test the flow and increase it if necessary (see page 19).

•Plug the hose in the suction fitting situated furthest from

the stairs.

•Modify the hose length by adding or removing a section.

•Orient the inlet jets so as to push the hose away from the steps.

•If necessary add the deflector wheel.

•Check the air tightness of the circuit: between all hose sections,

between the hose and the valve, between the valve and the

skimmer.

•Reduce the flow (see page 19).

•Close the main drain valve.

6/Troubleshooting

2 1

The T5 Duo is not operating

correctly

The T5 Duo doesn't

clean all the zones of

your swimming pool

The T5 Duo does not stay on

the bottom of the pool

The T5 Duo stays stuck

at the stairs of

your pool ladder

The T5 Duo moves slowly

and air bubbles form at

the level of the suction outlet

The T5 Duo moves above

the waterline

The T5 Duo stays stuck

at the main drain plug

Cleaning the Diaphragm

If the cleaner stops, check the diaphragm for blockage.

•Turn cleaner over (Figure 16).

•Inspect diaphragm and push through debris or obstacles

to clear.

If not blocked, check the diaphragm for wear or damage.

Removing the Diaphragm

•Unscrew the casing (Figures 17 and 18).

•Unscrew the handle (Figure 19), release the inner tube then

remove the diaphragm (Figure 20).

•Check the diaphragm for possible traces of wear and rinse profusely

with water. If necessary replace with a new diaphragm.

7/Cleaning, replacing the Diaphragm

2 2

Figure 16

Figure 17 Figure 18

Figure 19 Figure 20

Casing

Handle

Reassembling the Diaphragm

•Insert the diaphragm back on the inner tube.

•Insert the diaphragm/inner tube assembly into the upper part of

the cassette. Align the stop markers on the diaphragm with

the notches and pull gently on the inner tube (without twisting)

until the edge of the diaphragm becomes visible (Figures 21 and 22).

•Screw the handle back onto the upper part of the cassette.

•Assemble the casing then slide the ring and the nut onto

the handle (Figure 23).

•Insert the engine into the body and thread the handnut

down tight (Figure 24).

•Make sure the extension tube swivels freely by spinning it

(Figure 25).

2 3

Figure 21 Figure 22

Figure 23

Figure 24

Figure 25

Notch

Stop

Upper part of the cassette

Edge of the Diaphragm

Outer tube

Nut

Upper ring

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Zodiac Schwimmbadroboter Handbücher

Zodiac

Zodiac Vortex OV 3450 Bedienungsanleitung

Zodiac

Zodiac CyclonX OC 3300 TILE Bedienungsanleitung

Zodiac

Zodiac Kontiki Bedienungsanleitung

Zodiac

Zodiac Vortex 3.2 Bedienungsanleitung

Zodiac

Zodiac VX65 iQ Vortex-Pro Bedienungsanleitung

Zodiac

Zodiac RV 5500 iQ Bedienungsanleitung

Zodiac

Zodiac Pacer Bedienungsanleitung

Zodiac

Zodiac Pacer Bedienungsanleitung

Zodiac

Zodiac RV 5480 iQ Bedienungsanleitung

Zodiac

Zodiac EvoluX iQ Series Bedienungsanleitung

Zodiac

Zodiac MX8 Bedienungsanleitung

Zodiac

Zodiac B3 Bedienungsanleitung

Zodiac

Zodiac T3 Bedienungsanleitung

Zodiac

Zodiac RC 4100 Bedienungsanleitung

Zodiac

Zodiac Genius Bedienungsanleitung

Zodiac

Zodiac RC 4370 Bedienungsanleitung

Zodiac

Zodiac CyclonX Bedienungsanleitung

Zodiac

Zodiac Automatic Pool Cleaner Bedienungsanleitung

Zodiac

Zodiac MX6 Elite Bedienungsanleitung

Zodiac

Zodiac CYBERNAUT NT Bedienungsanleitung

Zodiac

Zodiac Vortex iQ Bedienungsanleitung

Zodiac

Zodiac Vortex RV5380 Bedienungsanleitung

Zodiac

Zodiac IQ904-PS Bedienungsanleitung

Zodiac

Zodiac VORTEX-PRO EC15 Series Bedienungsanleitung

Beliebte Schwimmbadroboter Handbücher anderer Marken

POOLGOODS

POOLGOODS PoolGobbler Pro Bedienungsanleitung

Maytronics

Maytronics Dolphin POOL UP Bedienungsanleitung

iRobot

iRobot Verro 600 Bedienungsanleitung

Kokido

Kokido SKOOBA K535CBX/18/EU Bedienungsanleitung

SmartPool

SmartPool Robo-Kleen PLUS Bedienungsanleitung

Brilix

Brilix BARACUDA Bedienungsanleitung

Aiper

Aiper Orca 1200 Pro Bedienungsanleitung

Hayward

Hayward Navigator Pro Bedienungsanleitung

Polaris

Polaris Vac-Sweep 380 Bedienungsanleitung

Pentair

Pentair Prowler 710 Bedienungsanleitung

BWT

BWT D500 Bedienungsanleitung

Kokido

Kokido xtrovac 70 Bedienungsanleitung

Pentair

Pentair RACER Bedienungsanleitung

Pentair

Pentair REBEL 2 Bedienungsanleitung

SmartPool

SmartPool Robo Kleen Plus Bedienungsanleitung

Steinbach

Steinbach Twin Bedienungsanleitung

STA-RITE

STA-RITE PoolShark Vacuum Bedienungsanleitung

BWT

BWT BC 30 Bedienungsanleitung