Zodiac PH Expert Bedienungsanleitung

H0434900.G - 2019/11

More documents on:

www.zodiac.com

- English

pH dosing system

Translation of the original instructi ons in french





• Failure to respect the warnings may cause serious damage to the pool equipment

or cause serious injury, even death.

• Only a person quali ed in the technical  elds concerned (electricity, hydraulics or

refrigera on) is authorised to perform this procedure. The quali ed technician

working on the appliance must use/wear personal protec ve equipment (such as

safety goggles and protec ve gloves, etc.) in order to reduce the risk of injury oc-

curring when working on the appliance.

• Before servicing the appliance, ensure that it is switched o and isolated from the

power supply circuit.

• The appliance is intended to be used only for swimming pools and spas; it must not

be used for any purpose other than that for which it has been designed.

• This appliance is not intended for use by children.

• This appliance is not intended for use by persons (including children, aged 8 years

and above) with reduced physical, sensory or mental capabili es or lack of experi-

ence and knowledge, unless:

- they have been given supervision or instruc on, by a person responsible for their

safety, concerning use of the appliance in a safe way by a person responsible for

their safety; and

- they clearly understand the hazards involved.

• Children should be supervised to ensure that they do not play with the appliance.

• The appliance must be installed according to the manufacturer’s instruc ons and

in compliance with all applicable local and na onal standards. The installer is re-

sponsible for installing the appliance and for compliance with na onal installa on

regula ons. Under no circumstances may the manufacturer be held liable in the

event of failure to comply with applicable local installa on standards.

• For any work other than the simple user maintenance described in this manual, the

product should be referred to a quali ed professional.

• Incorrect installa on and/or use may cause serious damage to property or serious

injuries (possibly causing death).

• All equipment, even postage and packing paid, travels at the risks and perils of the

recipient. The la er shall issue reserves in wri ng on the carrier's delivery slip if

damage is detected, caused during transport (con rma on to be sent to the car-

rier within 48 hours by registered le er). In the event that an appliance containing

coolant has been turned on its side, men on your reserva ons in wri ng to the

carrier.

• If the appliance su ers a malfunc on, do not try to repair it yourself; instead con-

tact a quali ed technician.

• Refer to the warranty condi ons for details of the permi ed water balance values

for opera ng the appliance.

• In addi on to using spare parts manufactured by unauthorised third-party manu-

facturers, deac va ng, elimina ng or by-passing any of the safety mechanisms in-

tegral to the appliance, will automa cally void the warranty.

• Do not spray insec cide or any other chemical (inﬂ ammable or non-inﬂ ammable)

in the direc on of the appliance, as this may damage the body and cause a  re.

• Do not touch the fan and/or any moving parts and do not insert anything, including

your  ngers in the vicinity of the moving parts while the appliance is in opera on.



This symbol means that your appliance must not be thrown into a normal bin. It will be selecvely collected

for the purpose of reuse, recycling or transformaon. Any substances it may contain which are potenally

dangerous to the environment shall be eliminated or neutralised.

Request informaon on recycling procedures from your retailer.



• The electrical supply to the appliance must be protected by a dedicated 30

mA dierenal residual current protecon device (RCD), complying with the

standards and regulaons in force in the country where it is installed.

• Do not use an extension cord to plug in the appliance; connect the appliance

directly to a suitable power supply circuit.

• Before carrying out any operaons, check that:

- The voltage indicated on the rang plate of the appliance corresponds to the

mains voltage,

- The power grid is adapted to the power requirements of the appliance, and is

grounded.

- The plug (where applicable) is suitable for the socket.

• In the event of abnormal funcon or signs of overheang such as a burning

odour from the appliance, turn it of immediately, unplug / disconnect it from

its power supply and contact a professional.

• Before accessing the enclosure for any reason, ensure that all power to the

appliance and also power to any accessories or external devices which may

be connected to the appliance, is disconnected from the mains power supply.

• Do not disconnect and reconnect the appliance to the power supply when in

operaon.

• Do not pull on the power cord to disconnect it from the power supply.

• If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualied persons in order to avoid a hazard.

• Do not aempt to carry out any servicing or maintenance operaons with

wet hands or while the appliance is wet.

• Ensure that all terminals for mains power are free in good condion and free

of corrosion and/or dirt/debris.

• For any component or sub-assembly containing a baery: do not recharge or

dismantle the baery, or throw it into a re. Do not expose it to high tempera-

tures or direct sunlight.

• In stormy weather, disconnect the appliance from the power supply to pre-

vent it from suering lightning damage.

• Do not immerse the appliance in water (with the excepon of cleaners) or

mud.

CONTENTS

 4

1.1 I Descrip on 4

1.2 I Technical speci ca ons 4

1.3 I Dimensions and marking 5

 6

2.1 I Preparing the pool 6

2.2 I Hydraulic connec ons

2.3 I Electrical connec ons 10

 11

3.1 I Control box presenta on 11

3.2 I Checks before commissioning 11

3.3 I Calibra ng the sensor 12

3.4 I Priming the peristal c pump 13

3.5 I Se ngs 13

 16

4.1 I Changing the peristal c tube 16

4.2 I Winterizing 16

 17

5.1 I Appliance behaviour 17

5.2 I Displays 18

 





 

     



 





• Write down your retailer's contact details to help you  nd them more easily and  ll in the "product"

informa on on the back of the manual; your retailer will ask you for this informa on.





AControl box

BSuc on cane

CPipework installa on kit

DpH sensor

E Threaded sensor holder

FFixture collar

GWall-moun ng bracket kit

HPack of pH4, pH7 bu er solu ons



Power supply voltage 220-240 VAC-50 Hz - 1-phase

Electric output 9W

Protec on index IP65

Maximum peristal c pump ﬂ ow 1.5L/hr

Maximum counter pressure at the injec on point 1.5 bar

Correc on acidic or basic

pH sensor tolerance 5 bar / 60°C / maximum speed 2m/s

Measurement scale 0.0 - 14.0 pH (± 0.1 pH)

pH sensor response  me 15 seconds



Peristal c pump

Master switch

BNC connector socket for pH sensor

Cable gland for direct coupling with the  ltering system

Connector for suc on tube

Connector for injec on tube

Cable gland for suc on cane cable

Cable gland for 230Vac/50Hz power cord





2.1.1 Water balance

It is essen al that the pool water balance is controlled and adjusted before installing the appliance. Making

sure that the pool water balance is correct from the very start will reduce the likelihood of encountering

problems on the  rst days of opera on or during the season the pool is in use.

Even though it is an automa c regula on system, it is essen al to carry out regular water analyses

to check the water balance parameters.

Unit Recommended

values To increase To decrease Test frequency

(during the

season)

pH /7.2 – 7.4

Use the appliance in

"alkaline" dosage mode

and/or increase the set

point.

Use the appliance in

"acidic" dosage mode

and/or decrease the

set point.

Weekly

Free

chlorine

mg/L

or ppm 0.5 – 2 Add chlorine (manually

or using an automated

system)

Stop the release or

produc on of chlorine Weekly

(alkalinity

or bu er

capacity)

°f (ppm) 8 – 15

(80 – 150)

Add alkalinity corrector

(Alca+ or TA+) Add hydrochloric acid Monthly

(hardness

level)

°f (ppm) 10 – 30

(100 – 300) Add calcium chloride

Add a scale

sequestering

agent or carry out

decarbona on

Monthly

Cyanuric

acid

(stabiliser)

mg/L

or ppm < 30 / Par ally empty the

pool and re ll it Quarterly

Metals

(Cu, Fe,

Mn…)

mg/L

or ppm ± 0 / Add a metal

sequestering agent Quarterly

2.1.2 Appliance injec on programme

Example of 4 cycles with a set point at 7.4 pH and acid regula on (standard alkalinity):

 : 20% injec on (2 min) & 80% pause (8 min)

 : 50% injec on (5 min) & 50 % pause (5 min)

 : 75% injec on (7 min 30 sec) & 25% pause (2 min 30 sec)

 : 100% injec on (10 min)

• The injec on programme is of course inverted when a basic dosage is selected.

• Ac ve chlorine is more eﬃ cient with the correct pH level.

• Maximum release rate is 1.5 L/h. This dosage ensures that the set point is reached quickly and

accurately.

• This propor onal injec on is cyclic and the cycle dura on is 10 minutes. The

dose will change according to the distribu on of injec on  mes and pauses.

The propor onality adjusts automa cally and the balancing between the

di erent doses is made in 0.15 pH steps.

2.1.3 Adjus ng dosage according to alkalinity

The pH level of water is poten ally unstable. Its stability is governed by the level of water alkalinity (also called "TA" for

‘‘Total alkalinity’’). If the TA is low (< 100 ppm), the pH will become poten ally unstable and conversely if the TA is high

(>150 ppm).

In order to always achieve op mal water balance, the appliance has a feature that allows users to adjust the quan ty of

corrector product poten ally injected depending on the water TA (see §"3.5.4 "Dosage" menu")





2.2.1 Sensor and injec on point loca on

• The pH sensor must be installed more than 30 cm before or a� er a piping bend. Use the op onal

POD kit if necessary. Failing to follow this posi oning can lead to incorrect or unstable measure-

ments.

• The  p of the pH sensor must not be in contact with the pipe.

• Never install a pH sensor before the  ltra on pump or between the pump and the  lter. This

would cause random readings and a shortened service life.

• The pH sensor must be placed a� er the  lter and before the hea ng system,

• It must be placed ver cally or sloping at a maximum of 45°; it should never point downwards.

• The injec on point must be the last element on the pool circuit, a� er any hea ng and water treatment

systems.



2.2.2 Sensor and injec on point installa on

• There must be at least 60 linear cm between the sensor and the injec on point. If this is not possible, use

the POD kit available as an op on or a check valve.

• Fixture collars (or the POD kit) must be installed on rigid Ø50 PVC pipes. A Ø63 adapter is available as an

op on.

• The POD kit is recommended if a Redox (chlorine) regula on module has also been installed.

• Maximum pressure must not exceed 1.5 bar.

• Drill a hole with a diameter between 16 and 22 mm on the pipe at the selected loca ons for the pH sensor

and the injec on point.

• Then install the  xture collars.

• Use Teﬂ on tape to make sure the threads on the sensor holder, the injec on valve and its adapter are

water ght.

• Screw down the one or more sensor holders onto the  xture collar or a POD kit (op onal), 



• Carefully unscrew the protec on tube from the sensor,  



• Rinse the end of the sensor with tap water and shake o excess water,  

 

 



• Screw the sensor into the sensor holder, holding the BLUE connector in one hand and the black connector

in the other to avoid tangling the cable,  

• Once the sensor is installed, it can be connected to the BNC connector's control box, 



Andere Handbücher für PH Expert

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Zodiac Prüfgeräte Handbücher

Zodiac

Zodiac Diag box Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung