Zonet ZSR2104WE Bedienungsanleitung
Wireless 125Mbps AP Router
User’s Manual
Contents
1.Introduction....................................................................................2
2.SafetyNotification...........................................................................3
3.Hardware Installation.....................................................................4
4.Web Management Settings............................................................6
4.1.PrimarySetup……………………………………..…………………7
( how to set up 125Mbps mode )………………………………12
4.2.Security…………………………………………………………….13
4.3.System……………………………………………………………..19
4.4.DHCPServer…….…………………………………………………23
4.5.SNMPInfo………………………………………………………….25
4.6.Status………………………………………………………………27
4.7.AdvancedWireless………. .. …………………………………….29
4.8.AccessFilters………………………………………………………33
4.9.VirtualServer…………..…………………………………………..36
4.10.RoutingTable……………………………………………………..39
4.11.DynamicDNS……………….……………………………………42
5. Troubleshooting.....................................................................….44
1
1. Introduction
Thank you for purchasing this Wireless 125Mbps AP Router.
This user guide will assist you with the installation procedure.
The package you have received should contain the following items:
---AP Router Wireless 125Mbps AP Router
---Installation CD（with manual inside）
---Quick Installation Guide
---Power Supply / Cord
---Ethernet Cable
Note: if anything is missing, please contact your vendor
2
2. Safety Notification
Your Wireless AP Router should be placed in a safe and secure location. To
ensure proper operation, please keep the unit away from water and other
damaging elements. Please read the user manual thoroughly before you install
the device. The device should only be repaired by authorized and qualified
personnel.
---Please do not try to open or repair the device yourself.
---Do not place the device in a damp or humid location, i.e. a bathroom.
---The device should be placed in a sheltered and non-slip location within a
temperature range of +5 to +40 Celsius degree.
---Please do not expose the device to direct sunlight or other heat sources. The
housing and electronic components may be damaged by direct sunlight or heat
sources.
3
3. Hardware Installation
Front Panel
The front panel provides LED’s for device status. Refer to the following table for
the meaning of each feature.
LED STATUS Description
PWR/STAT Off No power
Red On 1. Power on 2. Reset to default 3.
Firmware upgrade (first 1 minute)
Red On
Red Blink 1. System up 2. Power on 3.
Firmware upgrade
Red Blink
LAN Off no Ethernet link detected
Green ON 10/100Mbps Fast Ethernet link
detected. No activity.
Green On Green Blink Indicates data traffic on the 10/100
Mbps LAN
WAN Orange Blink Indicates data traffic on the 10/100
Mbps LAN
G Yellow Blink Indicates the device is linking or
active data through wireless links
4
Rear Panel
The rear panel features 4 LAN ports, 1 WAN port and Reset button. Refer to the
following table for the meaning of each feature.
Power (DC 5v)
Used to connect to the power outlet. Only
use the power adapter provided with the
device. Use of an unauthorized power
adapter may cause damage to your device
and violate your warranty.
Reset Press the Reset Button for approximately
ten seconds, all configurations will set to
factory default settings.
LAN The RJ-45 Ethernet ports used to connect
your PC, hub, switch or Ethernet network.
WAN The RJ-45 Ethernet port labeled WAN is
used to connect your AP Router to your
xDSL or Cable modem.
AP Router Default Settings
The default settings are shown following.
User
Password admin
AP Router IP Address 192.168.1.1
AP Router Subnet Mask 255.255.255.0
RF ESSID wlan-g
11g RF Channel 6
Mode
Disabled
11b+g
11g only
AfterBurner
Encryption Disabled
DHCP client Enabled
5
4 Web Management Settings
START UP & LOGIN
In order to configure the Wireless 11g AP Router, you must use your web
browser and manually input http://192.168.1.1 into the Address box and press
Enter. The Main Page will appear.
In order to configure the Wireless 125Mbps AP Router, you must input the
password into the Password box and leave blank on the User Name box. The
default password is “admin”.
Once you have logged-in as administrator, it is a good idea to change the
administrator password to ensure a secure protection to the Wireless 125Mbps
AP Router. The Security Settings section described later in this manual describes
how to change the password.
Once you have input the correct password and logged-in, the screen will change
to the Setup page screen.
WARNING : TURN ON POWER SUPPLY
Quick power cycle can caused system corruption. When power on, be careful
not to shut down in about 5 seconds, because data is writing to the flash.
6
4.1. Primary Setup
Primary Setup
This screen contains all of the Router's basic setup functions.
.
7
Most users will be able to configure the AP Router and get it working properly
using the settings on this screen. Some Internet Service Providers (ISPs) will
require that you enter AP Router Wireless 802.11g AP Router specific
information, such as User Name, Password, IP Address, Default Gateway
Address, or DNS IP Address. This information can be obtained from your ISP, if
required.
MAKE CORRECT NETWORK SETTINGS OF YOUR COMPUTER
To change the configuration, use Internet Explorer (IE) or Netscape
Communicator to connect the WEB management 192.168.1.1.
WAN:
Host Name:
This entry is necessary for some ISPs and can be provided by them.
Domain Name:
This entry is necessary for some ISPs and can be provided by them.
Configuration Type:
The Router supports four connection types:
Dynamic IP Setting:
Static IP Address
PPPoE (Point-to-Point Protocol over Ethernet)
PPTP (Point-to-Point Tunneling Protocol)
Dynamic
8
Static IP Address
PPPoE
9
PPTP
These types can be selected from the drop-down menu next to Internet
Connection. The information required and available features will differ depending
on what kind of connection type you select.
Some descriptions of this information are included here:
Internet IP Address and Subnet Mask
This is the Router's IP Address and Subnet Mask as seen by external users on
the Internet (including your ISP). If your Internet connection requires a static IP
address, then your ISP will provide you with a Static IP Address and Subnet
Mask.
Default Gateway
Your ISP will provide you with the Gateway IP Address.
DNS (Domain Name Server) IP Address
Your ISP will provide you with at least one DNS IP Address.
User Name and Password
Enter the User Name and Password you use when logging onto your ISP
through a PPPoE or PPTP connection.
10
Inhaltsverzeichnis
Andere Zonet WLAN-Router Handbücher
Zonet
Zonet ZSR9104WE Bedienungsanleitung
Zonet
Zonet ZSR4174WE Bedienungsanleitung
Zonet
Zonet ZSR1114WE Bedienungsanleitung
Zonet
Zonet ZSR1124WE Bedienungsanleitung
Zonet
Zonet ZSR4154WE Bedienungsanleitung
Zonet
Zonet ZSR4134WE Bedienungsanleitung
Zonet
Zonet ZSR0104UP Bedienungsanleitung
Zonet
Zonet ZSR4154WS Bedienungsanleitung
Zonet
Zonet ZSR0104CP Bedienungsanleitung
Zonet
Zonet ZSR1114WE Bedienungsanleitung
Zonet
Zonet ZSR1124WE Bedienungsanleitung
Zonet
Zonet ZSR4134WS Bedienungsanleitung
Zonet
Zonet ZSR4124WE Bedienungsanleitung
Zonet
Zonet ZSR1134WE Bedienungsanleitung
Zonet
Zonet ZSR4174WE Bedienungsanleitung
Zonet
Zonet ZSR4124WE Bedienungsanleitung
Zonet
Zonet ZSR0104CP Bedienungsanleitung
Zonet
Zonet ZSR0104DE Bedienungsanleitung
Zonet
Zonet ZSR4134WE Bedienungsanleitung
Zonet
Zonet ZSR4154WE Bedienungsanleitung
