Zoom F6 Bedienungsanleitung
You must read the Usage and Safety Precautions before use.
Quick Guide
© 2019 ZOOM CORPORATION
Copying or reprinting this manual in part or in whole without permission is prohibited.
Product names, registered trademarks and company names in this document are the property of their respective companies.
You might need this manual in the future. Always keep it in a place where you can access it easily.
The contents of this manual and the specifications of the product could be changed without notice.
Windows®is a trademark or registered trademark of Microsoft®Corporation.
Mac is a trademark or registered trademark of Apple Inc.
The Operation Manual can be downloaded from the ZOOM website (https://www.zoom.jp/docs/f6).
This page has les in PDF and ePub formats.
The PDF le format is suitable for printing on paper and reading on a computer. The ePub format can be
read with electronic document readers and is designed for reading on smartphones and tablets.
2
Connections
■Left side
Condenser
mic
Dynamic mic
• Computer
Audio interface
Card reader
• FRC-8 F Series remote controller
• Dedicated AC adapter (ZOOM AD-17)
• 5V mobile battery (commercially-available)
Playback device, etc. BTA-1 or other dedicated wireless adapter
Inputs for mics, instruments and mixers
■Right side
Headphones
Timecode
Inputs for mics, instruments and mixers
The timecode cable input and output should have the following specications.
Tip: Input to (output from external device)
Ring: Output from (input to external device)
Sleeve: GND
The XLR 1–6 inputs have the following specications.
1：GND
2：HOT
3：COLD
12
3
NOTE
3
Preparations
Supplying power
Power can be supplied using AA batteries, an L battery or USB.
■AA batteries
1. Loosen the screw in the battery cover on
the bottom.
2. Open the battery cover on the bottom,
and remove the battery case.
3. Install 4 AA batteries in the battery case.
4. Put the case into the compartment.
5. Close the battery cover and tighten the screw.
■L battery
1. Slide the battery in the direction of the
arrow while pressing it toward the re-
corder.
After loading batteries, use Menu > SYSTEM > Settings > Power Source > Type to set the correct type of
battery.
NOTE
A USB type C cable can also be connected to the USB port to operate it using AC power.
HINT
4
Installing the camera mount adapter
1. Remove the 4 screws from the top of the .
2. Align the screw positions of the camera mount
adapter with those of the , and tighten the
screws.
3. Attach the to a tripod, for example, and
then attach the camera with the camera mount
adapter screw.
5
Loading SD cards
1. Open the SD card slot cover, and insert an SD card.
To remove the SD card, push it further into the slot and then pull it out.
HINT
Before using SD cards that have just been purchased or that have been formatted on a computer, they
must be formatted by the . To format an SD card, use Menu > SYSTEM > SD Card > Format.
NOTE
Turning the power on and off
1. Press and hold to turn the power on.
Press and hold to turn the power off.
HINT
• If “No Card!” appears on the display, conrm that an SD card is inserted properly.
• If “Card Protected!” appears on the display, the SD card write-protection is enabled. Slide the lock
switch on the SD card to disable write-protection.
• If “Invalid Card!” appears on the display, the card is not formatted correctly. Format the card or use a
different card.
NOTE
6
Setting the language (rst time starting up)
The rst time you turn the power on after purchase, set the display language when the Lan-
guage setting screen opens.
1. Use and to select the display language, and
press .
The language setting can be changed later using Menu > SYSTEM > Language.
HINT
Setting the date and time (rst time starting up)
When the Date and Time setting screen opens after the Language settings screen, set the
date and time.
1. Use and to select the item to change, and
press .
2. Use and to change the value, and press .
3. Use and to select "Enter", and press .
The date and time setting can be changed later using Menu > SYSTEM > Settings > Date/Time > Set Date/
Time.
HINT
7
Display overview
■Home Screen
Status icons
Stopped
Recording
Paused
Playing back
Recording/playback
sample rate
Clipping indicator
Level meter
Track number
Red: Input enabled
Green: Playback track enabled
Gray: Input disabled
Frame rate
INT: Internal timecode enabled
EXT: External input timecode enabled
Mono
Stereo
Ambisonic
Counter
During recording: Elapsed/remaining recording time)
During playback: Elapsed/remaining playback time)
Power type and remaining amount
USB: Power supply connected to port
EXT: L battery
AA: AA batteries
Recording/playback timecode
Recording/playback take name
When stopped, press and hold
to show the name that will be
given to the next recorded take.
Adjacent track numbers are con-
nected to show input link settings.
The has two Record setting modes, Linear (16/24-bit) and Float (32-bit), with the following character-
istics.
Linear: This mode records ordinary 16/24-bit WAV les. Adjust input (trim) levels so that the clip indica-
tors do not light when recording. The level meters show input levels after adjustments.
Float: This mode records 32-bit oat WAV les. Adjusting input levels is unnecessary. As long as maxi-
mum input levels are not exceeded, both quiet and loud sounds can be recorded with high quality.
The level meters show levels after adjustments by [Track ] knobs.
HINT
Some of the screen will appear differently when the recording mode is Float (32 bit).
NOTE
8
Input and output settings
Setting the input source
Set the input source using Menu > INPUT > PFL > Input 1–6
> Source.
Open the Menu Screen.
/ Select up/down.
Conrm.
Setting Explanation
Mic Select this when connecting a mic or other equipment with a low input level.
Mic (PH) Use this setting for mic level with phantom power.
Line Select this when connecting line level equipment.
The input level will be reduced 20 dB compared to when "Mic" is selected.
Line (PH) Use this setting for line level with phantom power.
USB 1–4 When the “AIF with Rec” setting is on, computer output signals are treated as
input signals.
• Menu > INPUT > Phantom Settings can be used to set the phantom power voltage and change the
power conservation setting (power supply during playback).
• To return to the Home Screen from the Menu Screen, press to go back one menu level at a time.
HINT
9
Adjusting input levels (trim)
When the recording setting mode is not “Float (32 bit)”, use
Menu > INPUT > PFL > Input 1–6 > Trim to adjust the input
level.
Open the Menu Screen.
/ Select up/down, adjust value.
Conrm.
See “Adjusting headphone volume” ( →P. 10) for how to adjust the headphone volume.
HINT
Enabling tracks
You can select which among Inputs 1–6 to use.
Inputs will be recorded on tracks with the same numbers. For example, Input 1 will be
recorded on track 1 and Input 2 will be recorded on track 2.
1. Turn the with the same number as the
input you want to record right, making the track
status indicator light.
Status indicator Track number screen
background color Explanation
Lit red Red The input is enabled.
Unlit Gray The input is disabled.
10
Adjusting track volume
1. Turn for a track to adjust its volume.
Adjusting headphone volume
1. Turn .
Andere Handbücher für F6
4
Inhaltsverzeichnis
Andere Zoom Diktiergerät Handbücher
Zoom
Zoom Handy REcorder H1 Bedienungsanleitung
Zoom
Zoom F8 Anleitungen und Rezepte
Zoom
Zoom H4next Bedienungsanleitung
Zoom
Zoom F8n Pro Bedienungsanleitung
Zoom
Zoom Q2HD Bedienungsanleitung
Zoom
Zoom H3-VR Bedienungsanleitung
Zoom
Zoom H3-VR Bedienungsanleitung
Zoom
Zoom iQ5 Bedienungsanleitung
Zoom
Zoom F8n Bedienungsanleitung
Zoom
Zoom F1 Bedienungsanleitung
Zoom
Zoom F1 Montageanleitung
Zoom
Zoom F1 Bedienungsanleitung
Zoom
Zoom Handy REcorder H1 Bedienungsanleitung
Zoom
Zoom H4n Pro Bedienungsanleitung
Zoom
Zoom H6 Handy Recorder Bedienungsanleitung
Zoom
Zoom H4N Bedienungsanleitung
Zoom
Zoom F6 Bedienungsanleitung
Zoom
Zoom Handy recorder H2 Bedienungsanleitung
Zoom
Zoom H4N Bedienungsanleitung
Zoom
Zoom H4n Pro Bedienungsanleitung
