ZDAS-16CA-8
Wireless & Wired Security Alarm System
Page 8of 16
2, If ARM succeed, the Buzzer will long sound,ARM Indicate Light on; if the system refuse the
dictate, the Buzzer will short sound 3 times, it means that some zone is activated or set
ARM already. If there is an ARM Delay, the system will exit the delay after inputs ARM
dictate, and short sound every second till delay time is over. It will not send alarm before
some zone is activated.
3.4.2 BOUNDARY ARM, also named Home ARM, when a BOUNDARYARM start
alarm status
, non-BOUNDARYARM will not activate alarm(BOUNDARY Zone Set:
See 4.9)
1, Operation: Press F
2
Shortcut Key or press “ ”on Remote Controller to set ARM.
Zone Number: 1~16
2, ARM Succeed, the Buzzer will long sound, ARM Indicate Light on; if the system refuse the
dictate, the Buzzer will short sound 3 times, it means no BOUNDARY Zone preset or it is
already Set BOUNDARYARM.
3.4.3 Set Single Zone ARM/ DIS- ARM: the specified zone start alarm
status, the other
zones will not activated alarm
1, Set single zone ARM: Zone Number(01～16)＋F
1
Shortcut Key,
2, Set single zone DIS-ARM: Password(6 bits)+Zone Number(01～16)＋F
4
Shortcut Key,
3, ARM Succeed, the Buzzer will long sound,ARM Indicate Light on; if the system refuse the
dictate, the Buzzer will short sound 3 times, it means no BOUNDARY Zone preset or it is
already Set BOUNDARYARM or Single Zone ARM.
Note: BOUNDARY ARM and Single Zone ARM can be set at the same time or turn
to EXIT ARM if ARM not stopped.
3.4.4 Fast alarmed set，
，，
，it can be operated direct without time late
Operating: press *+F1
3.5 Disarm:
DIS-ALARM Status
1, Operation: User Password (6 bits)＋F4 (Confirm Key) (Factory User Password:
123456), or press “ ” key on Remote Controller
2, Disarm Succeed: ARM Indicate Light off; if the system refuse the dictate, the Buzzer will
short sound 3 times, or system has already disarm.
3.6 Remote Control
When System is set as Remote Controllable (See 4.18), (Factory Setting: non-remote control),
use a preset phone or mobile phone to remote control the alarm system to ARM, disarm, record
or monitor.
3.6.1 Remote ARM, Disarm:
Use a preset phone or mobile to remote control the alarm
system toARM or DIS-ALARM status
1, Ring time when dial the preset phone: (Set in Step 4.19, Factory Setting is 8 times);
2, Input User Password: after a long sound “Di”, input “1” to startARM Status, if succeed, you
will hear a long sound ”Di”, if not succeed, you will hear 3 short sound; input “2” to disarm, if
succeed, you will hear a long sound ”Di”, if not succeed, you will hear 3 short sound.
3.6.2 Remote Monitor:
Use a preset phone or mobile to remote monitor the alarm system
1, In remote control status, Input User Password: after a long sound “Di”, press “3”, then you
can hear the instant sound from the zones; press “8” to return
3.6.3
Remote control to siren:
In remote control status, press “4” start siren, press “5” exit
siren.
3.7 Set Receive Alarm by Telephone
; when the alarm connected the phone or mobile
phone, user can remote control the system by phone or mobile phone. There are two methods
as following
1, Factory Setting: after connected, press “1” key on telephone or mobile phone to receive
recorded sound, after twice record and indicate sound “Du”, input user password to
Remote Control Sta
tus
; press “2” hang up to Confirm; press “3” start directly Remote
Control S
tatus.
2, It can also be programmed as: (See 4.21) after connected, receive alarm sound after 5
