ZUUM H10X10 Bedienungsanleitung

[email protected] * 1-888-861-7351 * www.zuum.life ZM0915

H10X10

Model: H10X10 a 10 in 10 out HDMI Matrix Switch allows you to route 10 HD sources to any 10 HD displays! The 10x10 HDMI Matrix switch is a complete

HD routing solution for whole home HDTV systems. It provides 3D support, Ultra HD 4K2K, and with 2U Rack mounting for professional installations. In

addition, the H10X10 allows for effortless control of up to 10 devices through Ethernet control, IR remote control, RS-232 and the front panel.

1.0 Features:

>Connect up to 10 HDMI sources to 10 HDMI displays (TV’s)

>High definition video up to 4K2K@60Hz@8bits, 1080p@60Hz@12bits

> Audio supports up to LPCM 7.1 @192KHz Dolby TrueHD DTS-HD

>Easy to use front panel control or included remote control for switching sources

>Built in Ethernet control, assign IP or set up as DHCP and enter IP into browser for computer-based control

>Built in RS232 console port for input / output selecting

>Front panel lights shows input /output connectivity and LCD display shows status

2.0 Installation View:

[email protected] * 1-888-861-7351 * www.zuum.life ZM0915

3.0 Front Panel Indications:

Front Power LED Indication

Blue

Power on

Red

Standby

LED Off

Power Off

Front Input 1 ~ 10 LED Indications

Blue

Signal indication

LED off

No signal

Front Output 1 ~ 10 LED Indications

Blue

HDMI output indications

LED off

Output unlinked

Front Button Functions:

POWER

Power on (Blue) / Standby (Red)

DOWN

Down

LEFT

Left

RIGHT

Right

ENTER

Select confirm key

Back to main/channel setting

EDID

Copy EDID

LOCK

Button lock

ALL

Set selected input channel to all output. When you press ALL the second line of LCD will show IN and flashing,

select the input 1 ~ 10 or ALL. Then press ENTER

OFF

Turn off selected output, could be 1 ~ 10 or ALL. When you press OFF the second line of LCD will show IN and

flashing, select the output 1 ~ 10 or ALL then press ENTER

OUTPUT 1 ~ 10

Fast switch output

INPUT 1 ~ 10

Fast switch input

[email protected] * 1-888-861-7351 * www.zuum.life ZM0915

3.3 Panel button Details:

OUTPUT 1~10 ＆_INPUT 1~10

Press OUTPUT 1~10 to select output port then the input at IN line of LCD will blink, press INPUT 1~10 to select input port to switch the channel

ALL:

Press ALL button, the IN line of LCD will blink, press INPUT 1~10 to select input port to all output port. ENTER

OFF:

Press OFF button, the IN line of LCD will blink, press ALL or OUTPUT 1~10 to select which port to turn off. ENTER

EDID:

Press EDID button, it will show “From OUTPUT” at second line of LCD and the channel number will blink, press OUTPUT 1~10 to select which port to copy

EDID. (NOTE: See section 4.4 for EDID details.)

LOCK:

Press LOCK until LOCK LED is on. Located above button. The panel buttons and IR remote will be locked or non working. Press LOCK until LOCK LED is off

to unlock. Panel buttons and IR remote will work again.

3.3 LCD Panel Function:

Power on Main Screen

When the power is on and the main screen appears

Channel Setting on Main Screen

The Matrix will jump to channel setting screen after 10 seconds, press the MENU key to enter the main

Main MENU Option:

*1 - SWITCH

*2 - SCENE

*3 - ETHERNET

*4 - EDID

*5 - REMOTE ID

*6 - VERSION

10X10 HDMI MATRIX

OUT 1 2 3 4 5 6 7 8 9 10

IN 1 2 3 4 5 6 7 8 9

[email protected] * 1-888-861-7351 * www.zuum.life ZM0915

Operation:

> Press UP or DOWN key to move * to select an item for setting and press ENTER key to enter into subpage.

> In MENU you could use key 1~6 of IR remote control to select the functions as well.

> When the selected sub-page setting is completed, press the MENU button to return to the main page

4.0 LCD Main MENU Function Operations:

4.1 Switch：(Default: 1 2 3 4 5 6 7 8 9 10)

This function is used to switch the input/output port. Enter the SWITCH menu. Press the ENTER key, then the LCD second line INPUT will flash. Press

LEFT or RIGHT button to select the output to be modified. Then press Up or Down button to select the input port. After that, press ENTER to confirm setting.

It also works with INPUT/OUTPUT button of panel or IR remote

4.2 Scene:

SCENE function provide 10 sets of channel setting to fast reload for different application.

Load:

Reload saved scene, press UP or DOWN to select the number of setting ENTER to load.

Save:

Save current channel setting, press UP or DOWN to select the number and ENTER to save.

4.3 Ethernet

* IP Address

Subnet Mask

Gateway IP

DHCP Client

Media Type

MAC Filter

OUT 1 2 3 4 5 6 7 8 9 10

IN 1 2 3 4 5 6 7 8 9 10

LOAD

SAVE

LOAD 1

1 2 3 4 5 6 7 8 9

SAVE 1

[email protected] * 1-888-861-7351 * www.zuum.life ZM0915

IP Address: (Default: 192.168.0.10)

This function can setup MATRIX host intranet ”IP Address”, press the ENTER, the left-most number of second row will flash, then press the UP or DOWN

button to change the numbers, , press LEFT or RIGHT to move to another location, the move to a position number will flash, press ENTER to complete the

setting. NOTE: If DHCP Client is set to ENABLE you can not change IP.

Subnet Mask: (Default 255.255.255.0)

This function can setup MATRIX host intranet “Subnet Mask”, press the ENTER, the left-most number of second row will flash, then press the UP or DOWN

button to change the numbers Press ENTER, , press LEFT or RIGHT to move to another location, the move to a position number will flash, press ENTER to

complete the setting. NOTE: If DHCP Client is set to ENABLE you can not change IP.

Gateway: (Default 192.168.0.1)

This function can setup MATRIX host intranet “Gateway”, press the ENTER, the left-most number of second row will flash, then press the UP or DOWN

button to change the numbers Press the ENTER, , press LEFT or RIGHT to move to another location, the move to a position number will flash, press ENTER

to complete the setting.

DHCP Client: (Default Disable)

When DHCP Clients setup to “Enable”, the MATRIX host will automatically get IP Address, Subnet Mask, Gateway, if setup at “Disable”, the MATRIX Host IP

Address needs to go through “ ETHERNET” menu to set IP Address, Subnet Mask, Gateway, press ENTER, the second row will flash, then press the UP or

DOWN to select DISABLE, ENABLE, then press ENTER to complete the setting.

Media Type: (Default AUTO)

This function can setup MATRIX host intranet “Media Type, press the ENTER, the second row will flash, then press the UP or DOWN button to select AUTO、

10MHalf、10MFull、100MHalf、100MFull, press ENTER to complete the setting.

IP Address

192.168. 0.10

Subnet Mask

255.255.255.0

Gateway

192.168. 0. 1

DHCP Client

Disable

Media Type

AUTO

[email protected] * 1-888-861-7351 * www.zuum.life ZM0915

MAC Filter: (Default Disable)

MAC Filter can setup with registered MAC Address in order to connect the MATRIX host Web UI, MAC Address is required by the Web page to fill in, this

function can only be setup at “DISABLE”, “ENABLE”, then press ENTER, the second row will flash, then press the UP or DOWN to select DISABLE, ENABLE,

then press ENTER to complete the setting.

4.4 EDID: (Default: 1080P LPCM-2CH)

Because the player output display resolution will be based on TV EDID, the Matrix provides two default EDID modes:” BUILD-IN MODE” and “COPY MODE”.

NOTE: 4K2K resolution you have to copy the EDID from your 4K2K monitor.

4.4.1 BUILD-IN MODE:

This mode supports video resolution 480p, 720p, 1080i/p at 24/50/60Hz, support 1080P LPCM two-channel audio and 5.1 channel. After enter BUILD-IN

MODE menu, press UP or DOWN key to select 1080P LPCM-2CH or 1080P LPCM-5.1CH, then press ENTER to confirm setting.

Copy Mode:

To fully support the TV resolution and audio mode, the matrix provides “COPY MODE” to copy TV EDID for input source reference. When using the copy

mode, recommend copying the lowest resolution TV EDID. Otherwise it may cause no picture display if the TV resolution is not able to support higher

resolution.

After entering COPY MODE menu, press UP or DOWN button to select the OUTPUT TV (1 to 10). Then press ENTER to confirm.

4.5 Remote ID：(Default IR ID: 4)

This function must be set to match the Matrix remote control IR1 with the matrix itself. A conflict with other devices remote control is avoided.

After entering MATRIX IR ID menu, press ENTER, the LCD LINE 1 number will flash. Then Press UP or DOWN button to select the number, and then press

ENTER to confirm.

When MATRIX IR ID setting is completed, MATRIX remote control IR1 must also have the same ID

in order to operation in normal.

Remote control IR ID setting mode: Press and hold the POWER button, then press the

number button which can be set from 0 to 9, total 10 groups. (See 5.1)

NOTE: These settings on IR1 remote control have to be done the first time you use the IR1 or when you change the

batteries.

COPY MODE

From OUTPUT: 1

BUILD-IN MODE

COPY MODE

1080P LPCM-2CH

1080P LPCM-5.1CH

MATRIX IR ID 4

＋

MAC FILTER

DISABLE

[email protected] * 1-888-861-7351 * www.zuum.life ZM0915

4.6 Version:

Display Matrix and WEB firmware version

5.0 Remote Control Function (IR1):

> To command the matrix locally, setup the remote control IR1 ID with the same code of the Matrix (see 4.5). The default code is

4. (Power+4)

> Warning: These settings have to be done the first time you use the IR1 or when you change the batteries.

> IR ID setup: press and hold POWER button then press Number key

NOTE: In Standby mode: The IR Remote can only control POWER on/off.

Remote control button define:

(Symbol)

(Function)

Power

ON/Standby (same as Matrix)

Left

Left (same as Matrix)

Right

Right (same as Matrix)

Up (same as Matrix)

Down

Down (same as Matrix)

Enter

Confirm (same as Matrix)

Menu (same as Matrix)

Quick key 1

Quick key 2

Quick key 3

Quick key 4

Quick key 5

Quick key 6

Quick key 7

Quick key 8

Quick key 9

Quick key 0

EDID (same as Matrix)

Off (same as Matrix)

Example: to connect output port 1 to input port 4, press the quick key 1 (OUTPUT 1) and then press the quick key 4 (INPUT 4).

FIRMWARE

VERSION 1.12

[email protected] * 1-888-861-7351 * www.zuum.life ZM0915

6.0 REMOTE Control Function:

HSM10X10 supports RS232 and TCP/IP control by the same command as below:

6.1 For RS232 CONSOLE/IP:

Connect the RS232 CONSOLE port to the COM port of the host by an F/M RS232 straight cable (pin 2 to pin 2; pin 3 to pin 3, pin 5 to pin 5) Communication

format is 9600, 8, N, 1 (9600 bps, 8 data bits, no parity check, 1 stop bit)

For Ethernet TCP/IP(Winsock) Default IP address: 192.168.0.10, Port:47011

6.2 Operation Instruction format:

Command + △(Space) + Parameter + Enter

[COMMAND]

[DESCRIPTION]

POWER △[y]

Power on/off

TX(n) △[n]

Set RXn to TXn

RX(n) △[m,m,m,m…]

Set RXn to multiple TXm,m,m,m…

MATRIX_ID△[p]

Set Matrix IR ID

EDID_COPY△[n]

Copy EDID from TX n

SAVE △[n]

Save setting to #n

LOAD △[in]

Load setting from #n

KEY△[y]

Panel buttons & IR remote control Lock/Unlock

DHCP△[y]

DHCP client on/off

IP_ADDRESS△[x.x.x.x]

Set Matrix IP address

SUBNET_MASK△[x.x.x.x]

Set Matrix subnet mask

GATEWAY△[x.x.x.x]

Set Matrix gateway

MEDIA_TYPE△[z]

Network speed select

MAC_FILTER△[y]

Mac filter on/off

STATUS

Show connection status

VERSION

Show firmware version

HELP

Help

[Symbol]

[Parameter]

01~10, ff=ALL

00=off, 01~10=1~10

00-09=0~9

0~255

00=off, 01=on

00=auto, 01=10M, 02=200M

Command Example:

> To route input 4 to output 1, send the following string: TX01△04Enter

> To route input 2 to all output, send the following string: RX02△ffEnter

> To route input 2 to output 1,2,4, send the following string: RX02△01,02,04Enter

> To put in standby the matrix, send the following string: POWER△00Enter

Commands are case insensitive.

The Matrix will reply OK once string is correct, NG in case of incorrect string

7. Web Control Function:

Initial IP Configuration

1. Setup MATRIX IP Address based on 4.3 ETHERNET section.

NOTE: If you set by DHCP go back to ETHERNET/IP address to confirm IP to enter into browser.

2. Input IP Address on a web page, so you can link to the Web UI of the MATRIX host.

3. Web UI Operation below:

Switch Settings:

POWER

Control MATRIX power on and standby

OUTPUT

Display output 1~10, you can change the display name by the Aliases page

INPUT

Display input 1~10, this field is a drop down menu, you can change the display name by

the Aliases page.

RELOAD

Get MATRIX host message.

ADVANCED

Enter into the “Advanced” page.

APPLY

Complete the setting

[email protected] * 1-888-861-7351 * www.zuum.life ZM0915

Advanced:

IP ADDRESS

Change IP address

SUBNET MASK

Change Subnet mask

GATEWAY IP

Change Gateway IP

MEDIA TYPE

Change 10/100/Auto detect

DHCP CLIENT

When setup as Enable, the MATRIX host will automatically get IP Address

Subnet Mask, Gateway. If setup as Disable, the MATRIX host IP Address、Subnet

Mask、Gateway need to set from Matrix console.

AUTO RESET

The terminal connection will support 4 users on line at same time; this function can

setup the connect time to avoid long connections with users. When over the set connect

time, the terminal will automatically disconnect the link. . (0: no time setup, 1 ~ 255

Minute time range that can be setup)

DEVICE NAME

Can change device name

MAC ADDRESS

Click to enter MAC Filter setup page

ONLINE

Terminal connection users display, the max. 4 users on line.

MEMORY

Click to enter memory setup page

MAC FILTER

Click to enter MAC Filter setup page

ALIASES

Click to enter Aliases setup page

BACK

Back to SWITCH SETTING page

APPLY

Click Apply after setting changes

Inhaltsverzeichnis

Andere ZUUM Schalten Handbücher

ZUUM

ZUUM MAHCL4X4V2 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung