Zycoo SC15 Bedienungsanleitung

Quick Installation Guide

SC15

Packing List

Network Ceiling Speaker (1PCS)

Warranty Card (1PCS) Quick Installation Guide (1PCS)

Power Adaptor (optional)

Mounting Bracket (optional)

安装方式一

1、在天花板上开一个直径在210±5mm的安装圆孔；

2、连接网线及需要的干接点信号线；

3、取下铁网放好；

4、小心将设备推入已开好的安装孔，旋转夹扣螺钉以调整夹片的位置，使夹扣能够勾住天花板；

5、拧紧四个螺钉，将四个夹扣扣紧，使夹扣能够牢固加紧天花板，最后盖上铁网。

φ210mm

天花

铁网

1、如需要安装支架，需要先将两扇支架安装到塑料圆形圈上；

安装方式二

中文

系统登录导向

1.连接好电源（或PoE）及网线。

2.设备启动完成后，按下恢复出厂设置按键5秒后，松开按键，设备进行IP播报。出厂默认DHCP，若未获取到IP地址，则

默认登录IP地址为192.168.1.101。直接在浏览器地址栏输入IP地址，即可进入设备登录界面，设备的缺省用户名及密码，

均为admin。

2、在天花板上开一个直径在220±5mm的圆孔；

3、连接网线及需要的干接点信号线；

4、取下铁网放好；

5、小心将设备推入已开好的安装孔，将组装好的支架套件装进后桶，紧贴天花板；

6、旋转夹扣螺钉以调整夹片的位置，使夹扣能够勾住支架套件；

7、拧紧四个螺钉，将四个夹扣扣紧，使夹扣能够牢固加紧支架套件，最后盖上铁网。

支架

铁网

φ220mm

支架

天花

恢复出厂设置导向

长按恢复出厂设置按键10秒以上，听到语音提示后松开，设备进入恢复设置状态，系统指示灯熄灭。恢复成功后，系统运

行指示灯进入闪烁状态。

恢复出厂设置按键

以太网接口

系统运行指示灯

RST

SYS

ETH0

COM

BTN

MIC+

VOL-

DC24V-

MIC-

VOL+

DC24V+

RST

SYS

ETH0

COM

BTN

MIC+

VOL-

DC24V-

MIC-

VOL+

DC24V+

直流电源24V输入+

直流电源24V输入-

按键呼叫

喇叭音量输出调节+

喇叭音量输出调节-

麦克风音频输入-

麦克风音频输入+

干接点信号常开输出

干接点信号公共端输入

干接点信号常闭输出

English

Installation Method 1

1.Cut a hole in the ceiling with 210±5 mm diameter.

2. Connect network cable and power supply (if PoE is not enabled on the network cable), and other cabling if required.

3. Detach the metal mesh (adsorbed by magnets).

4.Adjust the clips and place the back end of the ceiling speaker into the mounting hole, adjust the clips again for being

able to clamp the ceiling.

5.Tighten the screws in order to tighten the clamping of the clips with the ceiling, and then cover the metal mesh.

φ210mm

Ceiling

Metal Mesh

1.To install the ceiling speaker with mounting brackets, please first fix the two plates to the plastic ring.

Installation Method 2

Web Login

1.Connect network cable and power supply (if PoE is not enabled on the network cable).

2.Wait for 30 seconds then press and hold the RST button for 5 seconds and release, it will announce the IP address

obtained from the DHCP server. If there’s no DHCP server or DHCP fails, it will use default IP 192.168.1.101. In the

browser address bar input the IP address you hear to open its web management interface. Default username and

password admin/admin.

2. Cut a hole in the ceiling with 210±5 mm diameter.

3.Connect network cable and power supply (if PoE is not enabled on the network cable), and other cabling if required.

4.Detach the metal mesh (adsorbed by magnets).

5.Place the mounting bracket on top of ceiling, push the speaker back end into the ceiling through the mounting

bracket ring and ensure the mounting bracket is tightly attached to the ceiling.

6.Adjust the clips for being able to clamp with the mounting bracket.

7.Tighten the screws of the 4 clips in order to tighten the clamping of the clips with the mounting bracket and the

ceiling, and then cover the metal mesh.

Bracket

Metal Mesh

φ220mm

Bracket

Ceiling

Interfaces and Instructions

To reset factory defaults, press and hold the RST button for 10 seconds (5 seconds for IP address announcements)

and release, now you should hear voice prompts “Resetting factory defaults, rebooting…”, it means the speaker will

now reset.

Reset button

Ethernet interface

System LED indicator

RST

SYS

ETH0

COM

BTN

MIC+

VOL-

DC24V-

MIC-

VOL+

DC24V+

RST

SYS

ETH0

COM

BTN

MIC+

VOL-

DC24V-

MIC-

VOL+

DC24V+

Positive terminal of 24V DC input

Negative terminal of 24V DC input

Press To Talk Button

Volume Control+

Volume Control-

Audio In-

Audio In+

NO output of dry contact relay

COM input of dry contact relay

NC output of dry contact relay

Méthode d'installation 1

1. Découpez un trou dans le plafond de 210 ± 5 mm de diamètre.

2. Connectez le câble réseau et l'alimentation (si PoE n'est pas activé sur le câble réseau), et tout autre câblage si

nécessaire.

3. Détachez le treillis métallique (adsorbé par des aimants).

4.Ajustez les clips et placez l'extrémité arrière du haut-parleur de plafond dans le trou de montage, ajustez à nouveau

les clips pour pouvoir ﬁxer le plafond.

5. Serrez les vis aﬁn de resserrer le serrage des clips avec le plafond, puis couvrez le treillis métallique.

φ210mm

Plafond

Maille en métal

1.Pour installer le haut-parleur de plafond avec des supports de montage, veuillez d'abord ﬁxer les deux

plaques sur l'anneau en plastique.

Méthode d'installation 2

Français

Andere Handbücher für SC15

Inhaltsverzeichnis

Sprachen:

Andere Zycoo Sprecher Handbücher

Zycoo

Zycoo SH30 Bedienungsanleitung

Zycoo

Zycoo SL50 Bedienungsanleitung

Zycoo

Zycoo SC15 Bedienungsanleitung

Zycoo

Zycoo SQ10 Bedienungsanleitung

Zycoo

Zycoo SQ10 Bedienungsanleitung

Zycoo

Zycoo SC15 Bedienungsanleitung

Zycoo

Zycoo SL30 Bedienungsanleitung

Zycoo

Zycoo SC10 Bedienungsanleitung

Zycoo

Zycoo SC15 Bedienungsanleitung

Zycoo

Zycoo SW15 Bedienungsanleitung

Zycoo

Zycoo SC10 Bedienungsanleitung

Zycoo

Zycoo SC15 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung