ZyXEL Communications ZyWALL 1050 Bedienungsanleitung

ZyWALL 1050

Internet Security Appliance

Quick Start Guide

Version 2.00

7/2007

Edition 1

DEFAULT LOGIN

LAN Port 1

IP Address http://192.168.1.1

User Name admin

Password 1234

CONTENTS

ENGLISH 2

DEUTSCH 9

ESPAÑOL 16

FRANÇAIS 23

ITALIANO 30

日本語 37

РУССКИЙ 44

简体中文 51

繁體中文 57

ENGLISH

1 Checking the Package Contents

2 Rack-mounted Installation

Mount the ZyWALL in a 19-inch rack or place it on a sturdy, flat surface.

Note: Leave 10 cm of clearance at the sides and 20 cm in the rear.

1Align one bracket with the holes on one side of the ZyWALL and secure it with the included bracket

screws. Similarly, attach the other bracket.

2After attaching both mounting brackets, position the ZyWALL in the rack by lining up the holes in the

brackets with the appropriate holes on the rack. Secure the ZyWALL to the rack with the rack-mounting

screws.

Your package should

include one of each

of the following:

• ZyWALL 1050

•Powercord

• Rack-mounting kit

• RJ-45 Ethernet cable

• RS-232 console Y-cable

• Printed Quick Start Guide

• Configuration Reference Card

• Compact disk (CD)

ENGLISH

3 Connecting the Hardware

Make sure that the power switch on the rear panel is turned off before you make the hardware connections.

1It is recommended that you configure the ZyWALL before using it to protect your network. Use an Ethernet

cable to connect a computer to port 1.

2Use another Ethernet cable(s) to connect port 2 and/or port 3to an Ethernet jack with Internet access.

3Use the included power cord to connect the power socket on the rear panel to a power outlet.

4Push the power switch to the on position and look at the front panel. The PWR light turns on. The SYS light

blinks during system testing and initialization and then stays on when the system is ready.

4 Web Login

1Launch your web browser and go to http://192.168.1.1 (the

ZyWALL automatically redirects you to https://

192.168.1.1).

ENGLISH

2Click Yes to proceed if you get a security alert or

certificate screen.

3Enter admin as the user name and 1234 as

the password. Click Login.

4It is strongly recommended that you change the

password. Type and retype a new password, and click

Apply.

ENGLISH

5 Installation Setup Wizard

Use an installation setup wizard to connect to the Internet and register the ZyWALL and/or activate trial

services, like IDP and content filter.

Note: Use the installation wizard only for initial configuration starting from the default configuration.

Changes you make in the installation wizard may not be applied if you have already changed the

ZyWALL’s configuration.

The Status screen

opens. Click the

Wizard icon in the

upper right corner.

•INSTALLATION SETUP, ONE ISP sets up a sin-

gle Internet connection for ge2.

•INSTALLATION SETUP, TWO ISP sets up Inter-

net connections for ge2 and ge3.

ENGLISH

6 Default Settings and Port Details

The ZyWALL is configured for the following network topology by default.

The wizard screens vary depending on the

encapsulation type you use. Refer to information

provided by your ISP and the web help screens to

know what to enter in each field. You can leave fields

blank if you don’t have that information.

ENGLISH

Note: The USB ports, extension card slots, and hard disk slot are reserved for future use.

7 Troubleshooting

Port Interface Zone IP Address and DHCP Settings Suggested Use With Default Settings

1ge1 LAN 192.168.1.1, DHCP server enabled Protected LAN

2, 3ge2, ge3 WAN DHCP clients Connections to the Internet

4, 5 ge4, ge5 DMZ None, DHCP server disabled Public servers (such as web, e-mail and

FTP)

DIAL BACKUP aux None None Auxiliary modem

CONSOLE N/A None None Local management

Label Type Cable to Use

1~5 RJ-45 8-wire Category 5e or above Ethernet cable

DIAL BACKUP, CONSOLE RS-232 RS-232

Problem Corrective Action

None of the LEDs

turn on.

Make sure that you have the power cord connected to the ZyWALL and plugged in to an

appropriate power source. Make sure you have the ZyWALL turned on. Check all cable

connections.

If the LEDs still do not turn on, you may have a hardware problem. In this case, you should

contact your local vendor.

ENGLISH

8 Procedure to View a Product’s Certification(s)

1Go to www.zyxel.com.

2Select your product from the drop-down list box on the ZyXEL home page to go to that product's page.

3Select the certification you wish to view from this page.

Cannot access

the ZyWALL from

the LAN.

Check the cable connection between the ZyWALL and your computer or switch. Refer to

section 3 for details.

Ping the ZyWALL from a LAN computer. Make sure your computer’s Ethernet card is

installed and functioning properly. Also make sure that its IP address is in the same subnet

as the ZyWALL’s.

In the computer, click Start, (All) Programs, Accessories and then Command Prompt. In

the Command Prompt window, type "ping" followed by the ZyWALL’s LAN IP address

(192.168.1.1 is the default) and then press [ENTER]. The ZyWALL should reply.

If you’ve forgotten the ZyWALL’s password, use the RESET button. Press the button in for

about 5 seconds (or until the PWR LED starts to blink), then release it. It returns the ZyWALL

to the factory defaults (password is 1234, LAN IP address 192.168.1.1 etc.; see your User’s

Guide for details).

If you’ve forgotten the ZyWALL’s IP address, you can use the commands through the

console port to check it. Connect your computer to the CONSOLE port using a console

cable. Your computer should have a terminal emulation communications program (such as

HyperTerminal) set to VT100 terminal emulation, no parity, 8 data bits, 1 stop bit, no flow

control and 115200 bps port speed.

Cannot access

the Internet.

Check the ZyWALL’s connection to the Ethernet jack with Internet access. Make sure the

Internet gateway device (such as a DSL modem) is working properly.

Check ge2’s status in the Status screen. Use the installation setup wizard again and make

sure that you enter the correct settings.

Problem Corrective Action

DEUTSCH

1 Prüfen des Packungsinhalts

2 Rackmontage

Montieren Sie die ZyWALL an einem 19"-Rack oder stellen Sie es auf eine stabile Unterlage.

Hinweis: Lassen Sie seitlich 10 cm und hinten 20 cm Platz.

1Richten Sie eine Halterung an den Löchern an der Seite der ZyWALL aus und schrauben Sie sie mit den

mitgelieferten Montageschrauben fest. Verfahren Sie ebenso mit der zweiten Halterung.

2Wenn Sie beide Montagehalterungen befestigt haben, richten Sie die ZyWALL im so im Rack aus, dass

die entsprechenden Schraublöcher übereinander stehen. Befestigen Sie den ZyWALL mit den

Befestigungsschrauben am Rack.

Prüfen Sie ob alle

Teile vorhanden

sind:

• ZyWALL 1050

• Netzkabel

• Rackmontage-Zubehör

• RJ-45-Ethernetkabel

• Y-Kabel für RS-232-Konsole

• Kurzanleitung in Druckform

• Konfigurationskarte

•CD

DEUTSCH

3 Anschließen der Hardware

Stellen Sie sicher, dass der Netzschalter an der Rückseite des Geräts ausgeschaltet ist, bevor Sie die

ZyWALL in Betrieb nehmen.

1Es wird empfohlen, die ZyWALL zu konfigurieren, bevor Sie sie zum in Ihrem Netzwerk einsetzen.

Schließen Sie einen Computer mit einem Ethernetkabel an Port 1 an.

2Schließen Sie an Port 2 und/oder Port 3Ihren Router mit Internetzugriff an.

3Schliessen Sie den Netzanschluss des Geräts (an der Rückseite) mit dem mitgelieferten Netzkabel an

eine Netzsteckdose an.

4Schalten Sie den Ein/Aus-Schalter in die Position On und sehen Sie sich das vordere Bedienfeld an. Die

PWR-LED beginnt zu leuchten. Die SYS-LED blinkt während des Systemtests und der Initialisierung, und

sie leuchtet, wenn der Test abgeschlossen und das System bereit ist.

4 Anmelden im Internet

1Starten Sie Ihren Internetbrowser und rufen Sie die Seite

http://192.168.1.1 auf (der ZyWALL leitet Sie automatisch

zur Seite https://192.168.1.1 weiter).

Andere Handbücher für ZyWALL 1050

Inhaltsverzeichnis

Sprachen:

Andere ZyXEL Communications Firewall Handbücher

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL IDP 10 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL 110 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL 35 Handbuch

ZyXEL Communications

ZyXEL Communications ZyWALL SEM-DUAL Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWall Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWall Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL 1050 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWall ATP series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL 5 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL 110 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL 1050 Handbuch

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL 35 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications USG40 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL 1050 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL 35 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL 35 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ADSL 2+ Security Gateway Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL 110 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL 5 Handbuch

ZyXEL Communications

ZyXEL Communications ZyWall Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL SSL 10 Handbuch

ZyXEL Communications

ZyXEL Communications ZyWALL/USG Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL 5 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL 110 Series Bedienungsanleitung

Beliebte Firewall Handbücher anderer Marken

Cisco

Cisco S190 Bedienungsanleitung

Fortinet

Fortinet FortiGate Voice Series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 2300 Bedienungsanleitung

SecureLogix

SecureLogix ETM System Bedienungsanleitung

NETGEAR

NETGEAR ProSafe FVX538 Bedienungsanleitung

Lanner

Lanner FW-8877 Bedienungsanleitung

Huawei

Huawei USG6000 Series Installations- und Betriebshandbuch

H3C

H3C SecPath F5000-AI-15 Bedienungsanleitung

Nexcom

Nexcom DNA 1150 Bedienungsanleitung

Fortinet

Fortinet FortiGate-60 series Bedienungsanleitung

Cisco

Cisco 3110 Handbuch

Draytek

Draytek Vigor2860 Series Bedienungsanleitung

Lanner electronics

Lanner electronics FW-7650 Series Bedienungsanleitung

Swisscom

Swisscom Internet Backup Bedienungsanleitung

SonicWALL

SonicWALL NSa 5700 Bedienungsanleitung

DPtech

DPtech FW1000 SERIES Bedienungsanleitung

FEITIAN

FEITIAN MultiPass FIDO Bedienungsanleitung

EBLOCKER

EBLOCKER PRO Bedienungsanleitung