ZyXEL Communications MAX218M Montageanleitung

MAX218M

Support Note

Version V1.0

Last Modified 2011/9/29

1. Firmware naming rule............................................................................................4

2. Hardware specification of WiMAX Indoor CPEs ....................................................4

3. What is the MTK chipset version of MAX218M?...................................................5

4. What is the flash capacity of MAX218M?..............................................................5

5. What are the possible device status values we can find on Web GUI?.................5

6. What is the maximum length of the username? ...................................................5

7. What do I do if I forget the password? ..................................................................5

8. How do we verify if the Firmware has been upgraded successfully?....................5

9. Does MAX218M support mass firmware update and what’s the procedure? ......5

10. Which bandwidths does MAX218M support?.......................................................6

11. What is the antenna type?.....................................................................................6

12. How many ROM files do we have? ........................................................................6

13. How to enable/disable ARQ/H-ARQ/PHS? ............................................................6

14. How to disable PKMv2 key authentication? ..........................................................6

15. How to enable/disable RootCA verification?.........................................................7

16. How to change the IDLE mode time interval? .......................................................7

17. What is the HANDOVER criterion?.........................................................................7

18. How to check the Connection ID and QoS information?.......................................7

19. How to check the current service flow? ................................................................8

20. How can we determine if the CPE is running in SISO or Matrix A/B mode? .........8

21. Does MAX218M support SNMPv2 or SNMPv3 MIB table? ...................................9

22. Does MAX218M support syslog facility?................................................................9

23. Does MAX218M support bridge mode? ..............................................................10

24. Does MAX218M support VLAN tagging? .............................................................10

25. Does MAX218M Support VPN?............................................................................10

26. Does MAX218M support IP-CS with bridge? (Huawei’s property) ......................10

27. How many preset frequencies does MAX218M support?...................................10

28. Does MAX218M support TR-069? How to debug TR-069 issues?.......................11

29. Does TR-069 support HTTP authentication modes: none, basic, digest?............11

30. Does MAX218M support OMA-DM? ...................................................................11

31. How to backup CPE configuration?......................................................................11

32. How to restore CPE configuration?......................................................................12

33. What are the Common error messages? .............................................................12

34. What to check if we are facing a Ranging error?.................................................15

35. How to check SBC-REQ/REG-REQ/DSA-REQ message from trace log? ...............15

36. How to change the connecting criteria to “by RSSI” or “by CINR”? ....................16

37. How to display the current connecting frequency?.............................................16

38. How to check the real time RSSI and CINR? ........................................................16

39. Why is the modulation being fixed at QPSK1/2, even at very good RSSI/CINR?..17

40. How do we check whether the CPE sends out an EAP request? .........................17

41. How do we know if the CPE uses EAP-TTLS or EAP-TLS? .....................................17

42. How to check current connected BS ID?..............................................................17

43. How to check the current downlink and uplink modulation? .............................18

44. Does MAX218M fully support MIMO mode? ......................................................18

45. Can we use static modulation for IOT test? .........................................................18

46. What is the Modulation CINR threshold criterion? .............................................18

47. How do we check neighbor BS?...........................................................................18

48. How to check maximum DL/UL traffic rate profile that ISPs assign to user? ......19

49. How to change WiMAX WAN MTU size? .............................................................19

50. How can we debug DHCP issues? (Discover/offer/request/ACK message.) ........20

51. How to debug VoIP issues? ..................................................................................20

52. Does MAX218M support multicast?....................................................................20

53. How to lock NAP ID? ............................................................................................20

54. How to import a device certificate?.....................................................................20

55. How to export the device certificate? .................................................................20

56. What is the operating design of NAT: NAT/Bridge + Ethernet/PPPoE/GRE

tunnel/EtherIP tunnel? ................................................................................................21

57. How to check firmware version by command? ...................................................21

1. Firmware naming rule

Firmware Naming rule:

2.00(XXX.Y)ZZ For Example: 2.00(TPD.0)b1

2.00 Current trunk source code version

XXX: TPD Specific customer FW ID for customization

Y: .0, .1 , .2 , .3 ... Initial specific customer FW ID version. Increases by 1 for

next FW ID version (.1, .2, .3 …); issued when the

customer requests new or enhanced features, and for bugs

fixed for next official FW.

ZZ: b1, b2, b3, …

Beta X FW version for customer or PQA verification.

Changes to D0 after obtaining customer approval. (When

applying to official FW).

2. Hardware specification of WiMAX Indoor CPEs

Indoor WiMAX CPE

WiMAX Chipset

Version TX Power Antenna Gain Interface Wi-Fi Chipset

MAX208M MT7117 26dBm 6dBi 1D N/A

MAX208M2W MT7119 26dBm 6dBi 2D+2VoIP+WiFi(11n)

Ralink 802.11

b/g/n

MAX218M MT7117 26dBm 6dBi 1D N/A

MAX218MW MT7117 26dBm 6dBi 2D+WiFi(11n) Ralink 802.11

b/g/n

MAX218M1W MT7119 26dBm 6dBi 2D+1VoIP+WiFi(11n)

Ralink 802.11

b/g/n

MAX218M2W MT7119 26dBm 6dBi 2D+2VoIP+WiFi(11n)

Ralink 802.11

b/g/n

3. What is the MTK chipset version of MAX218M?

MT7117

4. What is the flash capacity of MAX218M?

64M NAND flash.

5. What are the possible device status values we can find on Web GUI?

Web GUISystem StatusWiMAX

Device Status: Disconnected, Scanning, Ready, Connecting, Connected

Connection Status: Network Search, Network Entry, Normal

6. What is the maximum length of the username?

GUI Login Username: The maximum length of Login username is 16 bytes

EAP Username: Maximum length of EAP anonymous ID and username is 50 bytes

7. What do I do if I forget the password?

The default password is 1234.

If it does not work, you will have to reset to factory default by pressing the reset

button for 5 to 10 seconds.

You will lose your entire configurations when resetting to factory defaults.

8. How do we verify if the Firmware has been upgraded successfully?

All LEDs turn off and the device reboots automatically.

9. Does MAX218M support mass firmware update and what’s the procedure?

Yes, MAX218M supports Multiboot using the regular Multiboot upgrade

procedure.

10.Which bandwidths does MAX218M support?

5, 7, 10 MHz

11.What is the antenna type?

Indoor MAX218M (3.5 GHz) is equipped with an internal Omni directional

antenna.

12.How many ROM files do we have?

We will release a default ROM based on key account’s setting.

13.How to enable/disable ARQ/H-ARQ/PHS?

The chipset vendor, MTK, didn’t release the command to us.

14.How to disable PKMv2 key authentication?

PKMv2 authentication can be disabled at GUIWiMAXProfileAuthentication

Settings.

15.How to enable/disable RootCA verification?

To disable the Root CA verification in EAP procedure, go to

WiMAX Profile Authentication setting Options Ignore Cert

Verification.

16.How to change the IDLE mode time interval?

You can change the IDLE mode interval at WiMAXProfile Connection

Settings Idle Mode Interval.

17.What is the HANDOVER criterion?

BS will decide the HANDOVER by CINR level.

18.How to check the Connection ID and QoS information?

Web GUIWiMAXService Flowclick the service flow and it will show the

detailStatic Connection ParametersScheduling Type.

19.How to check the current service flow?

Web GUIWiMAXService Flowclick the Downlink or Uplink service flow

Static Connection ParametersScheduling Type.

20.How can we determine if the CPE is running in SISO or Matrix A/B mode?

Web GUIWiMAXLink Statistics check LinkMIMO A Burst or MIMO B

Burst

Ex. When the value of MIMO A Burst is increasing, it indicates CPE is running in

MIMO A mode. If neither of MIMO A and MIMO B is increasing, then CPE is

running in SISO mode.

21.Does MAX218M support SNMPv2 or SNMPv3 MIB table?

MAX218M supports both SNMPv2 and SNMPv3 standard MIBs.

Private MIBs are not supported.

22.Does MAX218M support syslog facility?

Yes, access it at Maintenance LOG Log Setting.

23.Does MAX218M support bridge mode?

Yes, at Network setting WAN Operation Mode. It must run in ETH-CS mode.

24.Does MAX218M support VLAN tagging?

Yes. MAX218M supports port-based VLAN.

25.Does MAX218M Support VPN?

MAX218M supports PPTP, L2TP, and IPsec.

In Web GUI navigate to Security PPTP, L2TP, IPsec.

26.Does MAX218M support IP-CS with bridge? (Huawei’s property)

MAX208M supports IP-CS with NAT and ETH-CS with bridge which are included in

WiMAX forum definition. The device does not support IP-CS with bridge mode.

27.How many preset frequencies does MAX218M support?

Inhaltsverzeichnis

Andere ZyXEL Communications Tor Handbücher

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL P1 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL 70 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications EX5501-B0 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-873HNU(B)-51B Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications USG310 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications PPC 10 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL 10W Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications p-870hw series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P870HNU-51B Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL 35 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660HW-Tx v3 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 661H Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VSG-1200 V2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG3625-T20A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VSG1432 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications AMG1202-T10B Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 662HW Series Montageanleitung

ZyXEL Communications

ZyXEL Communications Network Device P-2302 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications EX5510-B0 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-662H Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL USG Series Montage- und Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VFG6005 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Unified Security Gateway ZyWALL 300 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG3927-B50B Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung

RTA

RTA 460MCBC-N2E Technisches Datenblatt