ZyXEL Communications ZyXEL ZyWALL 10W Bedienungsanleitung

ZyWALL 10W

Internet Security Gateway

Quick Start Guide

Version 3.60

December 2002

ZyWALL 10W Internet Security Gateway

Use a Y-cable to connect

your administration

computer or a modem

(with a cable converter)

to the CON/AUX port.

Make sure the CON/AUX

switch is pushed to the

appropriate side.

Hardware Installation

Rear Panel and Connections

The Front Panel

Refer to the User’s Guide for LED descriptions.

The PWR and CON/AUX LEDs turn on.

The SYS LED blinks and turns steady on.

The SYS LED turns red if power is too low.

The LAN, WAN and WLAN LEDs turn on, if

they are properly connected.

Reset to

default

configuration

file. See User’s

Guide.

Connect to a computer/hub

using a straight-through/

crossover Ethernet cable.

The computer must have

Ethernet NIC (Network

Interface Card) installed.

Turn off your ZyWALL.

Remove the protective

cover plate from the slot

and insert an optional

PCMCIA wireless LAN

card into the slot.

Never force, bend or twist

the wireless LAN card

into the slot.

The wireless LAN is

disabled by default.

The ZyWALL wireless

LAN may not work if you

do not use ZyAIR

wireless PC cards.

Connect to

your cable/DSL

modem.

Connect a

grounded

wire to

ground the

ZyWALL.

Do this last. Connect to a power source

using the supplied power adapter.

ZyWALL 10W Internet Security Gateway

Internet Account Checklist

Your ISP (Internet Service Provider) should have given you most of the following information. You do not

need to fill in every blank.

REQUIRED INFORMATION

Your device’s WAN IP Address (if given): __________________

DNS Server IP Address (if given): Primary __________________, Secondary _________________

Encapsulation:

Ethernet Service Type: _______________________

User Name: ____________ Password: ____________

PPTP User Name: ____________ Password: ____________

Your WAN IP Address: ____________ PPTP Server IP Address: ___________

Connection ID (if required): ____________

PPPoE (PPPoE) Service Name: ____________

User Name: ____________ Password: ____________

Setting Up Your Computer IP Address

Skip this section if your computer is already set up to accept a dynamic IP

address. This is the default for most new computers.

Your computer must have a 10M/100M NIC (Network Interface Card) and TCP/IP installed. TCP/IP should

already be installed on computers using Windows NT/2000/XP, Macintosh OS 7 and later operating

systems.

Windows 2000/NT/XP

1. In Windows XP, click start, Control Panel. In Windows 2000/NT, click Start, Settings, Control

Panel.

2. In Windows XP, click Network Connections.

In Windows 2000/NT, click Network and Dial-up Connections.

3. Right-click Local Area Connection and then click Properties.

4. Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and click Properties.

ZyWALL 10W Internet Security Gateway

5. The Internet Protocol TCP/IP Properties screen opens (the General tab in Windows XP).

-To have your computer accept a dynamic IP address, click Obtain an IP address automatically.

-If you want a static IP address, click Use the following IP Address and fill in the IP address

(192.168.1.2 to 192.168.1.254), Subnet mask (255.255.255.0), and Default gateway

(192.168.1.1) fields.

6. Click Advanced. Remove any previously installed gateways in the IP Settings tab and click OK to

go back to the Internet Protocol TCP/IP Properties screen.

7. Click Obtain DNS server address automatically if you do not know your DNS server IP

address(es).

If you know your DNS server IP address(es), click Use the following DNS server addresses,

and type them in the Preferred DNS server and Alternate DNS server fields.

If you have more than two DNS servers, click Advanced, DNS and click Add.

8. Click OK to close the Internet Protocol (TCP/IP) Properties window.

9. Click OK to close the Local Area Connection Properties window.

Checking/Modifying Your Computer’s IP Address

1. In the computer, click Start, (All) Programs, Accessories and then Command Prompt.

2. In the Command Prompt window, type "ipconfig" and then press ENTER to verify that your

computer’s static IP address is in the correct subnet (192.168.1.2 to 192.168.1.254 if using the default

ZyWALL LAN IP address). Alternatively, to have the ZyWALL assign your computer a new IP address

(from the IP pool), make sure your ZyWALL is turned on, type "ipconfig/renew" and then press

ENTER.

Your computer can now communicate with the ZyWALL using the LAN port.

Refer to your User’s Guide for detailed IP address configuration for other computer operating systems.

Accessing Your ZyWALL

Configure your ZyWALL using:

 Web Configurator

 SMT (System Management Terminal). Access the SMT via:

o LAN or WAN using Telnet

o Console port using terminal emulation software

ZyWALL 10W Internet Security Gateway

Procedure For Web Configurator Configuration

1. Make sure your computer IP address and

the ZyWALL IP address are on the same

subnet. Refer to the TCP/IP section in your

User’s Guide.

2. Launch your web browser and enter

“192.168.1.1” as the URL.

3. Enter "1234" (default) as the password and

click Login. In some versions, the default

password appears automatically - if this is

the case, just click Login. You should see a

screen asking you to change your password

(highly recommended).

4. Either enter a new password (and retype it

to confirm) and click Login or click Ignore.

You should now see the MAIN MENU screen.

Click the help icon (located in the upper right

portion of most screens) for online HTML help.

Procedure For SMT Configuration via Console Port

Configure a terminal emulation communications

program as follows: VT100 terminal emulation,

no parity, 8 data bits, 1 stop bit, data flow set to

none, 9600 bps port speed. Press ENTER to

display the SMT password screen.

Procedure For SMT Configuration via Telnet

Launch a Telnet program. In Windows, click

Start and then Run. Type “Telnet” followed by a

space and the IP address of the ZyWALL,

(192.168.1.1 is the default) and click OK to

display the password screen.

Enter the password (1234 is the default), to

access the SMT main menu.

ZyWALL 10W Main Menu

Getting Started Advanced Management

1. General Setup 21. Filter and Firewall Setup

2. WAN Setup 22. SNMP Configuration

3. LAN Setup 23. System Password

4. Internet Access Setup 24. System Maintenance

26. Schedule Setup

27. VPN/IPSec Setup

Advanced Applications

11. Remote Node Setup

12. Static Routing Setup

15. NAT Setup

99. Exit

Enter Menu Selection Number:

ZyWALL 10W Internet Security Gateway

Configuring for Internet Access

Configuration Using Web Configurator Wizard

1. Click Wizard Setup in the main menu. Follow

the online instructions to configure the first

wizard setup screen and click Next.

2. Use the information in the previous Required

Information table to enter the related fields in

the following screen and click Next.

3. In the following screen, repeat step 2 and click

Finish to complete the wizard setup.

Configuration Using SMT Menu 4

1. Enter 4 in the main menu and press ENTER to

display Menu 4 – Internet Access Setup.

2. Use the information in the previous Required

Information table to fill in related fields in the

SMT screen shown.

Menu 4 - Internet Access Setup

ISP's Name= ChangeMe

Encapsulation= Ethernet

Service Type= Standard

My Login= N/A

My Password= N/A

IP Address Assignment= Dynamic

IP Address= N/A

IP Subnet Mask= N/A

Gateway IP Address= N/A

Network Address Translation= SUA Only

Press ENTER to Confirm or ESC to Cancel:

Press ENTER at the “Press ENTER to Confirm or ESC to

Cancel:” prompt to save your settings.

ZyWALL 10W Internet Security Gateway

Activating the Wireless LAN

The wireless LAN is disabled by default. Before you enable the wireless LAN you should configure some

security, for example, setting MAC address filters and/or 802.1X security; otherwise your LAN will be

vulnerable upon enabling it.

Setting MAC filters

Using the SMT Using the Web Configurator

Type 3 in the main menu and press ENTER.

Type 5 in Menu 3 – LAN Setup and press

ENTER. Refer to the User’s Guide to set up

MAC address filters.

Click ADVANCED in the main menu and then

WIRELESS LAN.

Click the MAC Filter tab. Follow the on-line

help to set up MAC filters.

Setting 802.1X Security Using the Web Configurator

Follow the on-line help to set up 802.1X security using the WIRELESS LAN screens.

Enable the Wireless LAN

Using SMT Menu 3.5 Using the Web Configurator

Press SPACE BAR to select Yes in the Enable

Wireless LAN field and press ENTER.

Refer to the User’s Guide to enable WEP and

set up WEP keys.

Menu 3.5 - Wireless LAN Setup

Enable Wireless LAN= Yes

ESSID= Wireless

Hide ESSID= No

Channel ID= CH01 2412MHz

RTS Threshold= 2432

Frag. Threshold= 2432

WEP= Disable

Default Key= N/A

Key1= N/A

Key2= N/A

Key3= N/A

Key4= N/A

Edit MAC Address Filter= No

Press ENTER to Confirm or ESC to Cancel:

Select the checkbox

to activate wireless

LAN.

Follow the on-line help

to enable WEP and set

up WEP keys.

Click Apply.

ZyWALL 10W Internet Security Gateway

Troubleshooting

PROBLEM CORRECTIVE ACTION

None of the LEDs turn

on when you turn on the

ZyWALL.

Make sure that you have the correct power adapter connected to the ZyWALL and plugged

in to an appropriate power source.

If the error persists, you may have a hardware problem. In this case, you should contact

your local vendor.

Cannot access the

ZyWALL from the LAN.

Check the cable connection between the ZyWALL and your computer or hub. Refer to the

Rear Panel and Connections section for details.

Make sure your NIC (Network Interface Card) is installed and functioning properly.

Cannot ping any

computer on the LAN.

If the 10/100M LAN LEDs are off, check the cable connection between the ZyWALL and

your computer or hub.

Verify that the IP address and the subnet mask of the ZyWALL and the computers are on

the same subnet.

The WAN IP is provided after the ISP verifies the MAC address, host name or user ID.

Find out the verification method used by your ISP and configure the corresponding fields.

If the ISP checks the WAN MAC address, click MAINTENANCE and then DHCP Table to

display the ZyWALL 's WAN MAC address. Send it to the ISP.

If the ISP does not allow you to use a new MAC address, click ADVANCED, WAN and then

the MAC tab. Clone the MAC from the LAN as the WAN. ZyXEL recommends that you

configure this menu even if your ISP presently does not require MAC address

authentication.

If the ISP checks the host name, enter your computer’s name (refer to the Wizard Setup

section in the User’s Guide) in the System Name field in the first screen of the WIZARD

SETUP.

Cannot get a WAN IP

address from the ISP.

If the ISP checks the user ID, click ADVANCED, WAN and the ISP tab. Check your service

type, user name, and password.

Check the ZyWALL’s connection to the cable/xDSL device.

Check whether your cable/xDSL device requires a crossover or straight-through cable.

Cannot access the

Internet.

Click ADVANCED and then WAN and verify your settings.

Andere Handbücher für ZyXEL ZyWALL 10W

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ZyXEL Communications Tor Handbücher

ZyXEL Communications

ZyXEL Communications P-660HW-T - V2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 792H Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Unified Security Gateway ZyWALL 300 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG1312-T20A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VFG6005 Kurzanleitung

ZyXEL Communications

ZyXEL Communications P-2302R-P1 Series Handbuch

ZyXEL Communications

ZyXEL Communications EMG6726-B10A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications PMG5622GA Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications UAG5100 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL 2WE Montageanleitung

ZyXEL Communications

ZyXEL Communications Prestige 314 PLUS Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VSG1435-B101 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL 10W Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-661HNU Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications AMG1302-T10A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyWALL USG-1000 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications EMG2306-R10A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660HN-51 - Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-2302HWUDL-P1 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VSG1435-B101 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL USG100-Plus Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications AMG1302-T series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG3625-T50B Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ISG50 Montage- und Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung

RTA

RTA 460MCBC-N2E Technisches Datenblatt