ZyXEL Communications ES-116S Bedienungsanleitung

ES-116S

Ethernet Switch

User’s Guide

Version 1.00

Edition 1

11/2006

Table of Contents

ENGLISH 1

РУССКИЙ 13

ENGLISH

1 Introduction

The ES-116S is a 16-port switch that can be used to build

high-performance switched networks. The ES-116S is a

store-and-forward device that offers low latency for high-

speed networking.

1.1 Small Workgroup Application

The ES-116S can be used as a standalone switch to

which computers, servers and a printer are directly

connected to form a small workgroup.

2 Hardware Installation

The ES-116S is suitable for an office environment where

it can be placed on a desktop. If you want to mount it on a

wall instead, see section 5.

1Make sure the ES-116S is clean and dry.

ENGLISH

2Set the ES-116S on a smooth, leveled and sturdy flat

space strong enough to support the weight of the ES-

116S and the connected cables. Make sure there is a

power outlet nearby.

"Do NOT block the ventilation holes.

3 Rear Panel Connections

The RJ-45 ports and the power port are located on the

rear panel.

3.1 RJ-45 Auto-negotiating Ports

The 10Base-T/100Base-TX RJ-45 ports are auto-

negotiating and auto-crossover.

An auto-negotiating port can detect and adjust to the

optimum Ethernet speed (10/100Mpbs) and duplex mode

(full duplex or half duplex) of the connected device.

An auto-crossover (auto-MDI/MDI-X) port automatically

works with a straight-through or crossover Ethernet cable.

ENGLISH

"Make sure the cable length between

connections does not exceed 100 meters

(328 feet).

3.2 Power

Use the included power cable to connect your ES-116S to

a power source.

4 LEDs

The LEDs are located on the top panel.

The following table describes the LEDs.

LED Status Description

PWR OnThe ES-116Sis on and receiving power.

Off The ES-116S is not receiving power.

ENGLISH

5 Wall Mounting (optional)

See the product specifications for the size of screws to

use and how far apart to place them.

1Locate a high position on wall that is free of

obstructions. Use a sturdy wall.

2Drill two holes for the screws. Make sure the distance

between the centers of the holes matches what is

listed in the product specifications appendix.

"Be careful to avoid damaging pipes or

cables located inside the wall when drilling

holes for the screws.

3Do not screw the screws all the way into the wall.

Leave a small gap of about 0.5 cm between the heads

of the screws and the wall.

LINK/

ACT

On The port is connected to an Ethernet

network.

Blinking The port is receiving or transmitting data.

Off The port is not connected to an Ethernet

network.

LED Status Description

ENGLISH

4Make sure the screws are snugly fastened to the wall.

They need to hold the weight of the Prestige with the

connection cables.

5Align the holes on the back of the Prestige with the

screws on the wall. Hang the Prestige on the screws.

6 Product Specifications

The following table lists the specifications.

Ethernet Standard IEEE802.3 10BASE-T Ethernet

IEEE802.3u 100BASE-TX Fast Ethernet

ANSI/IEEE802.3 Auto-negotiation

IEEE802.3x Flow Control

Protocol CSMA/CD

Technology Store-and-Forward switching architecture

Supports broadcast storm control

Non-blocking Wire

Speed

3.2 Gbps

Transfer Rate Ethernet: 10Mbps (half duplex), 20Mbps (full

duplex)

Fast Ethernet: 100 Mbps (half duplex),

200Mbps (full duplex)

Data Forwarding

Rate

14880 pps for 10Base-T (Ethernet)

148800 pps for 100Base-T (Fast Ethernet)

Connector RJ-45; Auto-MDIX on all ports

MAC Address 8K MAC address table

ENGLISH

Certifications

Federal Communications Commission (FCC)

Interference Statement

This device complies with Part 15 of FCC rules. Operation

is subject to the following two conditions:

• This device may not cause harmful interference.

• This device must accept any interference received,

including interference that may cause undesired opera-

tions.

Memory Buffer 160 KB

Network Cable 10BASE-T: 100Ω2-pair UTP/STP Cat. 3, 4, 5

100BASE-TX: 100Ω2-pair UTP/STP Cat. 5

Power Supply External; 12 V, 1 A (100 - 240 V, 50 - 60 Hz)

Temperature Operating: 0ºC ~ 45ºC (32ºF ~ 122ºF)

Humidity Operating: 10% ~ 90% (Non-condensing)

Dimensions 293 (L) x 101.5 (W) x 33.7 (H) mm

Screw Size M3.5 * 15 mm (for wall mounting)

(not provided)

Distance Between

Holes

200 mm (center-to-center)

EMI & Safety FCC Class A, CE, C-Tick

ENGLISH

FCC Warning

This device has been tested and found to comply with the

limits for a Class A digital switch, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

commercial environment. This device generates, uses,

and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction

manual, may cause harmful interference to radio

communications. Operation of this device in a residential

area is likely to cause harmful interference in which case

the user will be required to correct the interference at his

own expense.

CE Mark Warning

This is a class A product. In a domestic environment this

product may cause radio interference in which case the

user may be required to take adequate measures.

Notices

Changes or modifications not expressly approved by the

party responsible for compliance could void the user's

authority to operate the equipment.

This Class A digital apparatus complies with Canadian

ICES-003.

ENGLISH

Cet appareil numérique de la classe A est conforme à la

norme NMB-003 du Canada.

Taiwanese BSMI (Bureau of Standards, Metrology

and Inspection) A Warning:

Viewing Certifications

Refer to the product page at www.zyxel.com.

Safety Warnings

"For your safety, be sure to read and follow

all warning notices and instructions.

• Do NOT use this product near water, for example, in a

wet basement or near a swimming pool.

• Do NOT expose your device to dampness, dust or cor-

rosive liquids.

ENGLISH

• Do NOT store things on the device.

• Do NOT install, use, or service this device during a thun-

derstorm. There is a remote risk of electric shock from

lightning.

• Connect ONLY suitable accessories to the device.

• Do NOT open the device or unit. Opening or removing

covers can expose you to dangerous high voltage points

or other risks. ONLY qualified service personnel should

service or disassemble this device. Please contact your

vendor for further information.

• Make sure to connect the cables to the correct ports.

• Place connecting cables carefully so that no one will

step on them or stumble over them.

• Always disconnect all cables from this device before

servicing or disassembling.

• Use ONLY an appropriate power adaptor or cord for

your device.

• Connect the power adaptor or cord to the right supply

voltage (for example, 110V AC in North America or

230V AC in Europe).

• Do NOT allow anything to rest on the power adaptor or

cord and do NOT place the product where anyone can

walk on the power adaptor or cord.

• Do NOT use the device if the power adaptor or cord is

damaged as it might cause electrocution.

• If the power adaptor or cord is damaged, remove it from

the power outlet.

Inhaltsverzeichnis

Sprachen:

Andere ZyXEL Communications Schalten Handbücher

ZyXEL Communications

ZyXEL Communications PLA4225 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Dimension ES-4024 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Dimension ES-4124 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications GS2200 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications GS1200-5HP Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications XGS2220 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ES-305 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Dimension GS-4024 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Dimension ES-3124PWR Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Dimension GS-2024 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ExtraSmart ES-1552 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Dimension GS-3012F Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications GS1100-16 - EDITION 1 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications XGS4700 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VES-1616 Handbuch

ZyXEL Communications

ZyXEL Communications MES-3728 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications GS-105B v2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications PMG5318-B20A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications GS1900-8 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ES-315 - V3.70 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Dimension Ethernet Switches Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications PLA-470 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Dimension GS-3012F Referenzhandbuch

ZyXEL Communications

ZyXEL Communications GS1100 Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung