2gig Technologies 2GIG-BRDG1-900 Bedienungsanleitung

2GIG-BRDG1-900

GO!BRIDGE IP COMMUNICATOR

INSTALLATION INSTRUCTIONS

TheGo!BridgeIPCommunicator™(2GIG‐BRDG1‐900)providesInternet

connectivitybetweenthemonitoringservice’sCentralStationandthe

Go!Control®Panel,whenthepanelisusedasahouseholdburglaralarm

system.

Itsupportsautomaticfirmwareupdates,providesinteractivesecurity

services,andincreasessupervisionusingsignal‐forwardingtotheCentral

Station.ForwirelesscommunicationwiththeControlPanel,the900MHz

TransceiverModule(2GIG‐XCVR)mustbeinstalledinthepanel.For

Internetaccess,theGo!Bridgemustbeconnectedtothelocalnetwork

routerusinganEthernetcable(notprovided).

Contents

Verifythatthepackageincludesthefollowing:

•1—Go!BridgeIPCommunicator

•1—5VDCUSBMini‐BPowerSupply

•1—Stand

• 1—PlasticPowerSupplyBracket(includesSelf‐AdhesiveBacking

andZipTie)

•1—WallSocketScrewforPowerSupplyBracket

• 2—PhillipsHeadScrewsandWallAnchors(tomountunitonwall)

•4—Self‐AdhesiveVinylBumpersforuseonunitorstand

Requirements

Beforeyouinstall,program,andtesttheGo!BridgeIPCommunicator,

ensurethecontrolpanelbeingpairedwiththeGo!BridgeIP

Communicatormeetstheserequirements:

•FirmwareVersion1.12(orhigher)

•2GIG‐XCVR900MHzTransceiver

IMPORTANT: ForcompliancewithUL1023:HouseholdBurglar‐

AlarmSystemUnits,theGo!Bridgemustbeinstalledinthe

sameroomastheInternetmodemorrouter.

NOTE: Toprotectdatasentviathelocalwirelessnetwork,itis

recommendedthatyouinstalltheGo!BridgeIPCommunicatoron

alocalnetworkwhereeitherWPA(Wi‐FiProtectedAccess)or

WPA2(Wi‐FiProtectedAccessII)encryptionisalreadyenabled.

Afterinstalling,programming,andtestingtheGo!BridgeIP

Communicator,youwillneedtoregisteranewcustomerwiththethird‐

partymonitoringservice.SeeRegistrationonpage3.

Figure 1 Go!Bridge Front View—LED Indicators and Learn Button

Powering ON the Go!Bridge IP Communicator

UsethesestepstopowerONtheGo!BridgeIPCommunicator:

1Attachthepowersupplytothebracket(provided)asfollows:

1a Insertthepowersupplyintotheenclosureontheplasticbracket.

SeeCinthefigurebelow.

1b Securethepowersupplytotheretainingbracketbythreadinga

ziptiethroughthebracket’sslots.SeeDinthefigurebelow.

1c Removethestripfromtheself‐adhesivebackingonthepower

supplybracket.

1d Affixtheadhesiveonthebrackettothewalloutlet.Thensecure

thebrackettotheoutletwiththewallsocketscrew(provided).

NOTE: AlwaysusetheprovidedpowersupplybracketintheUnited

States(andothercountrieswhereitisrequired).Canadadoesnot

requirethepowersupplyretainingbracket.

Figure 2 Power Supply and Bracket

2ConnecttheGo!Bridgetothepowersource.

NOTE: DonotconnectanEthernetcabletotheGo!BridgeIP

Communicatoratthistime.Youwillconnectthecablewhen

completingthestepsinProgrammingtheGo!BridgeIP

CommunicatorintotheControlPanel.

3(Optional)Placethestand(provided)onacounter,desktop,orother

flatsurface.SettheGo!BridgeIPCommunicatorinthestand.

NOTE: Toprotectsurfacesfromdamage,affixtheself‐adhesivevinyl

bumperstotheunitorstand.

4Verifythatthetwo(2)LEDsontheGo!BridgeIPCommunicator

illuminateinRED.SeeFigure1Go!BridgeFrontView—LEDIndicators

andLearnButtononpage1.

ANetworkLED

B900MHzLED

CLearnButton

A110VWallOutlet

BPlasticPowerSupplyBracketwithAdhesiveBacking

CACPowerSupply

DZipTie

Go!Bridge IP Communicator | Installation Instructions

NOTE: Ifthe900MHzLEDilluminatesinGREEN(thelowerLED),

verifythatthenetworkcableisnotconnectedtotheGo!Bridge

IPCommunicator.Ifthecableisdisconnectedanditisstill

illuminatedGREEN,usetheendofanopenpapercliptopress

andreleasetherecessedResetbutton.Thebuttonislocated

insidethesmallholeontheportsideoftheGo!BridgeIP

Communicator,directlyabovetheEthernetport.Thisrestores

thefactorysettings.SeeFigure3Go!BridgeIPCommunicator

RearView—PortsandRecessedResetButton.

Figure 3 Go!Bridge IP Communicator Rear View—Ports and

Recessed Reset Button

5AftertheGo!BridgeIPCommunicatorispoweredON,continuewith

ProgrammingtheGo!BridgeIPCommunicatorintotheControl

Panel.

Programming the Go!Bridge IP Communicator

into the Control Panel

UsethesestepstoplacethecontrolpanelandGo!BridgeIP

Communicatorinlearningmode.Thisgivesthecontrolpaneltheability

tolearnthenetworksettingstransmittedbytheGo!BridgeIP

Communicator.

NOTE: Toscrollbetweenoponsonthecontrolpanel,tapthe←

and→arrows.Tomovetothepreviousornextprompttapthe

↑and↓arrows.

1ConnectanEthernetcable(notincluded)totherouterand

Go!BridgeIPCommunicator.Donotplugthecableintotheuplink

port.

IMPORTANT: ForcompliancewithUL1023:HouseholdBurglar‐

AlarmSystemUnits,theGo!Bridgemustbeinstalledinthe

sameroomastheInternetmodemorrouter.

2EnsurethecontrolpanelispoweredON.ThentaptheHome 

button.

3Tapthesystemlogointhelower‐rightcornerofthecontrolpanel

Homescreen.

4AttheEnterYourCodescreen,enterthefour(4)‐digitmaster

installercodetogototheInstallerToolbox(1of2)screen.

5AttheInstallerToolbox(1of2)screen,tapSystemConfiguration.

6AttheQ1:SelectRFSensor#(01to48)screen,tapGoTo.

7AttheEnterQuestionNumber(2Digits)screen,enter92.

8AtQ92SelectNetworkDevice(0to1),tap→toscrollto(1)

Go!BridgeIPCommunicator.Thentap↓.

9AtQ:NetworkDeviceID(ReadOnly),tapLearn.Thisgivesthe

paneltheabilitytodiscovertheread‐onlynetworkdeviceID

transmittedbytheGo!BridgeIPCommunicator.

AtthePairwithXcvrDevicescreen,the“initiatinglearning

process”messageappears.

10 OntheGo!BridgeIPCommunicator,pressandreleasetheLearn

button(thisisthesmall,blackplasticbuttonontheLEDsideofthe

Go!BridgeIPCommunicatorbelowthe900MHzLED).Thistransmits

thedeviceIDtotheControlPanel.

Whenthe“learnoperationsucceeded”messageappearsandthe

paneldisplaystheType(Go!BridgeIPCommunicator)andID#,the

Go!BridgeIPCommunicatorandpanelarelinked.The900MHzLED

ontheGo!BridgeIPCommunicatoralsoflashesGREEN.

11 AtthePairwithXcvrDevicescreen,tapOK.Thentap↓to

continuewithConfiguringtheGo!BridgeIPCommunicatorSettings

below.

Configuring the Go!Bridge IP Communicator Settings

1AttheQ:SelectPort#(1to8)screen,entertheportnumberfor

thethird‐partymonitoringservices’server.Thentap↓.

2AtQ:Used(0to1),tap→toselectone(1)oftheseoptions:

•(0)Disabled(Recommended).Thisisthedefaultsetting.Most

userswillkeepthisportdisabled.ThentapNextandskipto

step3.

•(1)Enabled.Thentap↓.AttheQ:EnterPortValue(0‐65535)

screen,tap↓toacceptthedefaultportvalue.Next,attheQ:

EnterPortForwardIPAddressscreen,tap↓toacceptthe

addressconfiguredbytheprovider.Youcanconfigureupto

eight(8)ports.Ifyouarefinishedconfiguringports,tapNext.

3AttheSummaryofNetworkDevicescreen,tap↓.Verifythelistof

portnumbersandforwardIPaddressesappearsasprogrammed.

ThentapSkip.

4AtQ93EnterBroadbandNetworkFailureTime(1to255),enter

thedesirednumberofminutesthatmustpassbeforeanetwork

failuretriggerstheControlPaneltoissueatroublealert.The

defaultvalueis30minutes.Thentap↓.

NOTE: AtroublealertconsistsofanaudiblebeepandtheControl

Panel’sHomescreendisplaysatroublemessage.

5AtQ94SelectBroadbandNetworkFailureReport(0or1),tap→to

selectwhetherornottoreportthebroadbandnetworkfailureto

themonitoringservice:

•(1)Enabled.Thisisthedefaultsetting.Networkfailuresare

reportedtomonitoringservice.

•(0)Disabled.Networkfailuresarenotreported.

6TapEnd.

7AttheSummaryofSystemConfigurationscreen,verifythe

settings.ThentapSaveChanges.

8TapExittotheclosetheSystemConfigurationscreen.

LED Indicators

ThetabledetailstheLEDindicatorsontheGo!BridgeIPCommunicator.

ARecessedResetButton

BEthernetPort

CPowerSupplyPort

NetworkLED GlobeIcon

SolidGREEN Indicatesthepresenceofanexternalnetworkconnection.

FlashingGREEN NetworkcableispluggedinandIPaddressisactivelybeing

assigned.

SolidRED Networkcableunplugged.

900MHzLED IconLabeled“900MHz”

SolidGREEN LinkedandcommunicatingwiththeControlPanel.

FlashingGREEN LinkedtotheControlPanel.Communicationissuesexist.

SolidRED NotlinkedtotheControlPanel,turnssolidafteradevice

reset.

FlashingRED NotlinkedtotheControlPanel.

Go!Bridge IP Communicator | Installation Instructions

Verifying the Settings

InadditiontoverifyingthesettingsafterconfiguringtheGo!BridgeIP

Communicator,youcanalsoverifythesettingsatanytimeasfollows:

1AttheControlPanel’sHomescreen,tapSecurity.

2TapMenu.

3TapToolbox.

4IntheEnterYourCodetoAccesstheToolboxscreen,enterthe

masterusercode.

5Tap→toscrolltotheTo o l box(3of3)screen.ThentapGo!Bridge

IPCommunicatorStatus.

Asummaryscreendisplaysthefollowinginformation:

•NetworkConfiguration.Thenetworktypeconfiguration.

•IPAddress.TheIPAddressfortheGo!BridgeIPCommunicator.

Thisisa32‐bitnumericaddressthatidentifiesthedeviceonthe

network.

•SubnetMask.Thesubnetmaskforthenetwork.Alldevicesthat

arejoinedtoanetworkbelongtoasubnetwork.

•Gateway.TheIPAddressfortheaccesspointtotheexternal

network.Typically,thisistheIPAddressofthelocalnetwork

routerornodethatcontroltrafficforyourISP.

•MACAddress.ThisistheMediaAccessControl(MAC)Address.

ItisaphysicaladdressthatisencodedtotheGo!BridgeIP

Communicatorduringthemanufacturingprocess.

Testing

TheGo!BridgeIPCommunicatorteststhenetworkconnectiontothe

third‐partymonitoringservice.AreportshowsifGo!BridgeIP

Communicatorhassuccessfullyconnected(orfailedtoconnect)tothe

externalserver.

Registration

ToregistertheGo!BridgeIPCommunicatorwiththemonitoringservice,

refertoyourspecificprovider’sregistrationinstructions.

SPECIFICATIONS

Important Note

ShouldthelocalnetworkloseInternetaccessduetoapoweroutageor

interruption,theGo!BridgeIPCommunicatorisnotequippedwitha

backupbatterysystem.Tobestprepareforpowerfailuresandtoensure

thesecuritysystemmaintainsInternetaccesswiththemonitoring

serviceforlife‐safetycommunicationsduringpowerfailures,thelocal

networkmusthaveadedicatedUninterruptedPowerSupply(UPS)or

backupbatterysolutionfromathird‐partymanufacturerinplace.

LinearLLCdoesnotsupply,provide,recommend,ortesttheGo!Bridge

withanyUPSorbatterybackupsolution.Itisalsoassumedthatowner’s

InternetServiceProvider(ISP)maintainsabackupbattery(orpower

generator)fortheirremotenetworkequipment.

REGULATORY INFORMATION

Wireless Product Notice

Radiocontrolsprovideareliablecommunicationslinkandfillan

importantneedinportablewirelesssignaling;however,therearesome

limitationswhichmustbeobserved.

•ForUnitedStatesInstallationsOnly:Theradiosarerequiredto

complywithFCCRulesandRegulationsasPart15devices.As

such,theyhavelimitedtransmitterpowerandthereforelimited

range(approximately400ft.).

•Areceivercannotrespondtomorethanone(1)transmitted

signalatatimeandmaybeblockedbyradiosignalsthatoccur

onorneartheiroperatingfrequencies,regardlessofcode

settings.

• ChangesormodificationstothedevicemayvoidFCC

compliance.

•Infrequentlyusedradiolinksshouldbetestedregularlyto

protectagainstundetectedinterferenceorfault.

•Ageneralknowledgeofradioanditsvagariesshouldbegained

priortoactingasawholesaledistributorordealer,andthese

factsshouldbecommunicatedtotheendusers.

FCC Notice

ThisdevicecomplieswithPart15oftheFCCRules.Operationissubject

tothefollowingtwoconditions:

1Thisdevicemaynotcauseharmfulinterference,and

2Thisdevicemustacceptanyinterferencereceived,including

interferencethatmaycauseundesiredoperation.

Thisequipmenthasbeentestedandfoundtocomplywiththelimitsfor

ClassBDigitalDevice,pursuanttoPart15oftheFCCRules.Theselimits

aredesignedtoprovidereasonableprotectionagainstharmful

interferenceinaresidentialinstallation.Thisequipmentgeneratesand

canradiateradiofrequencyenergyand,ifnotinstalledandusedin

accordancewiththeinstructions,maycauseharmfulinterferenceto

radiocommunications.However,thereisnoguaranteethat

interferencewillnotoccurinaparticularinstallation.Ifthisequipment

doescauseharmfulinterferencetoradioortelevisionreception,which

canbedeterminedbyturningtheequipmentoffandon,theuseris

encouragedtotrytocorrecttheinterferencebyone(1)ormoreofthe

followingmeasures.

•Reorientorrelocatethereceivingantenna

•Increasetheseparationbetweentheequipmentandreceiver

•Connecttheequipmentintoanoutletonacircuitdifferent

fromthattowhichthereceiverisconnected

•Consultthedealeroranexperiencedradio/TVtechnicianfor

help

Anychangesormodificationsnotexpresslyapprovedbytheparty

responsibleforcompliancecouldvoidtheuser’sauthoritytooperate

theequipment.

WirelessSignalRange 500ft(152.4m),openair,withWirelessControlPanel

Transceiver SiliconLabsSI1001‐E‐GM2

TransceiverFrequency 25channelfrequency‐hoppingspreadspectrum,403

kHzchannelspacing(910.2‐920.275MHz)

ModulationType GFSKmodulation,128kpbs

RFPower +19dBmMaximum

Ethernet 10/100BaseT

Dimensions(LxWxH) 6.24x4.5x1in(159x114x25cm)

Weight 9.6oz

HousingMaterial Cycoloy™ResinC2800(RatedtoUL94V‐0:

FlammabilityStandard)

Color White

OperatingTemperature ‐32°Fto120°F,(0°Cto+49°C)

RelativeHumidity 5‐95%Non‐Condensing

OperatingVoltage 5VDC

Certification ETL,FCC,IC,IFETEL,andNOM

Go!Bridge IP Communicator | Installation Instructions

Industry Canada (IC) Compliance

ThisdevicecomplieswithIndustryCanadalicense‐exemptRSS

standard(s).Operationissubjecttothefollowingtwoconditions:(1)

thisdevicemaynotcauseinterference,and(2)thisdevicemustaccept

anyinterference,includinginterferencethatmaycauseundesired

operationofthedevice.

Repairstocertifiedequipmentshouldbemadebyanauthorized

Canadianmaintenancefacilitydesignatedbythesupplier.Anyrepairsor

alterationsmadebytheusertothisequipment,orequipment

malfunctions,maygivethetelecommunicationscompanycauseto

requesttheusertodisconnecttheequipment.

Usersshouldensurefortheirownprotectionthattheelectricalground

connectionsofthepowerutility,telephonelinesandinternalmetallic

waterpipesystem,ifpresent,areconnectedtogether.Thisprecaution

maybeparticularlyimportantinruralareas.

WARNING: Usersshouldnotattempttomakesuchconnections

themselves,butshouldcontacttheappropriateelectric

inspectionauthority,orelectrician,asappropriate.

LIMITED WARRANTY

ThisLinearproductiswarrantedagainstdefectsinmaterialand

workmanshipfortwo(2)years.Thiswarrantyextendsonlytowholesale

customerswhobuydirectfromLinearLLCorthroughLinearLLC’s

normaldistributionchannels.LinearLLCdoesnotwarrantthisproduct

toconsumers.Consumersshouldinquirefromtheirsellingdealerasto

thenatureofthedealer’swarranty,ifany.

TherearenoobligationsorliabilitiesonthepartofLinearLLCfor

consequentialdamagesarisingoutoforinconnectionwithuseor

performanceofthisproductorotherindirectdamageswithrespectto

lossofproperty,revenue,orprofit,orcostofremoval,installation,or

reinstallation.Allimpliedwarrantiesforfunctionality,arevalidonly

untilthewarrantyexpires.ThisLinearLLCWarrantyisinlieuofallother

warrantiesexpressedorimplied.

2GIGbyLinear

1950CaminoVidaRoble,Suite150

Carlsbad,CA92008USA

FortechnicalsupportintheUSAandCanada:

Dial:855‐2GIG‐TECH(855‐244‐4832)

Email:2gigtechsupport@linearcorp.com

Visitwebsitefortechnicalsupporthoursofoperation

FortechnicalsupportoutsideoftheUSAandCanada:

Contactyourregionaldistributor

Visitdealer.2gig.comforalistofdistributorsinyourregion

77‐000044‐001Rev.E

Inhaltsverzeichnis

Andere 2gig Technologies Netzwerk-Router Handbücher

2gig Technologies

2gig Technologies 2GIG BRDG1 900 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise