3D Systems Geomagic Touch Bedienungsanleitung

Haptic Device

Geomagic Touch

Quick Start Guide

3D Systems, Inc. 2

GEOMAGIC TOUCH QUICK START GUIDE

This quick start guide is a high-level overview of the steps you need to take to install, connect, and start to use the Geomagic Touch

haptic device. For detailed information, see the Geomagic Touch User Guide available on the http://support.geomagic.com website.

EXISTING USERS:

Remove any previous version of the PHANToM Device Driver that is installed on the computer:

• Win 7 or Win 8: Control Panel > Programs and Features > Uninstall a program

Delete all older setup les in the following location: C:\Users\Public\Documents\SensAble\

PERFORM THE FOLLOWING STEPS:

1. Go to http://support.geomagic.com to download and install the latest version of the Geomagic Touch Device Driver. (Go to http://

support.geomagic.com, from Products select Scanners and Hardware, then select the Touch device and Downloads).

2. After the device driver has installed, select the option in the installer to Restart Your Computer.

3. For a computer with no internet connection, follow the Driver Installation instructions found on page 2 of the Ethernet Adapter

manual (included with your adapter).

4. Connect the Ethernet Adapter, if you have not already installed the driver – wait a few minutes for the driver to be automatically

installed (you must have internet connection).

5. Connect the Geomagic Touch Device (Ethernet cable and power supply) as shown below. Connect the Ethernet cable to the

Adapter and then to either the ETH 1 or ETH 2 ports on the device. This is the 3D recommended connection. For alternative

connections check Appendix B: Alternate Connections in the Geomagic Touch User Guide.

6. Check the Network Status Indicator on the Windows 7 or 8 taskbar.

USB Port Ethernet Adapter Port ETH 1 or ETH 2

3D Systems, Inc. 3

If you see this rotating icon, wait (this may take up to 3 minutes).

Proceed when one of the icons below appears:

Geomagic Touch connected without network connection

Geomagic Touch connected with network connection

7. Double-click the Geomagic Touch Setup icon on your desktop or click Start>All Programs>3D Systems>Geomagic

Touch>Geomagic Touch Setup.

• Make sure the Device Model is set to Touch.

• Set Interface to LAN port.

• Set Host Name to match the Geomagic Touch serial number (located on the bottom of the device) to the corresponding device in this

list (this could take up to 3 minutes depending on your network connection).

8. Click the Pairing button in the Geomagic Touch Setup window.

3D Systems, Inc. 4

9. Press the Pairing button on the back of the device.

You must press the Pairing button before the Green progress bar times out – you have about 15 seconds (see image below).

If the progress bar times out before you have pressed the Pair button – repeat step 8.

3D Systems, Inc. 5

When the computer and device have been successfully paired – the notice below will appear.

10. Click OK, then press the Apply and OK buttons in the Geomagic Touch Setup dialog.

11. On the Desktop, click to open the Geomagic Touch Diagnostic or click Start>All Programs>3D Systems>Geomagic

Touch>Geomagic Touch Diagnostic.

12. Click the Next arrow in the bottom right of the dialog or click the Select tab to move on to the next step.

13. The Select tab initializes the Geomagic Touch device and begins to run to the Servoloop. Click the Next arrow when the six

remaining test tabs appear in the dialog to move on to the Calibration stage.

14. You will have to move the stylus through the complete range of motion to properly calibrate the device. Once each axis is

calibrated, its icon will turn Green (see image) when the device is properly calibrated.

15. Complete the remaining Geomagic Touch tests. When complete, click the red X in the top right corner to exit the Geomagic Touch

Diagnostic.

Go to http://support.geomagic.com to download the Geomagic Touch Device Guide.

Andere Handbücher für Geomagic Touch

Inhaltsverzeichnis

Andere 3D Systems 3D-Drucker Handbücher

3D Systems

3D Systems ZPRINTER 150 Bedienungsanleitung

3D Systems

3D Systems BFB-3000 Bedienungsanleitung

3D Systems

3D Systems Viper Pro SLA iPro 8000 Bedienungsanleitung

3D Systems

3D Systems ProJet 1200 Bedienungsanleitung

3D Systems

3D Systems FabPro 1000 Handbuch

3D Systems

3D Systems wematter Gravity Bedienungsanleitung

3D Systems

3D Systems ProJet 4500 Bedienungsanleitung

3D Systems

3D Systems Cubify CUBEX Duo Bedienungsanleitung

3D Systems

3D Systems CUBE Bedienungsanleitung

3D Systems

3D Systems ProJet 1200 Bedienungsanleitung

3D Systems

3D Systems CubePro Bedienungsanleitung

3D Systems

3D Systems wematter Density Bedienungsanleitung

3D Systems

3D Systems ProX 800 Bedienungsanleitung

3D Systems

3D Systems ProX 950 Bedienungsanleitung

3D Systems

3D Systems sPro Bedienungsanleitung

3D Systems

3D Systems CubePro Stücklistenhandbuch

3D Systems

3D Systems ProJet 660Pro Bedienungsanleitung

3D Systems

3D Systems CubeX Bedienungsanleitung

3D Systems

3D Systems CubePro Handbuch

3D Systems

3D Systems PROJET 3500 Referenzhandbuch

3D Systems

3D Systems ProJet 4500 Bedienungsanleitung

3D Systems

3D Systems Cubify CUBEX Duo Bedienungs- und Sicherheitshinweise

3D Systems

3D Systems ProJet 6000 Bedienungsanleitung

3D Systems

3D Systems ProX DMP 100 Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch