3D Systems Cubify CUBEX Duo Bedienungsanleitung

1

CUBEX

Replacing a

Main Board

PCB

2

Contents

What you will need ..................................................................................................... 3

Removing the Case and floor panel. .......................................................................... 4

Removing the damaged Main Board PCB.................................................................. 6

Fitting the new Main Board PCB ................................................................................ 7

Re attaching the floor panel and case........................................................................ 8

3

What you will need

Replacement Main Board PCB

3mm Hex Driver

2.5mm Hex Driver

4

Before beginning this process please ensure that the print pad is raised to the

top of the machine, all cartridges and the jet wipe have been removed from the

machine and that you have made a note of your Z height and offset settings as

these settings will not be present on the new PCB. Unplug the CubeX from

mains power.

Removing the Case and floor panel.

Using the 3mm hex driver remove the 8 case bolts (4 either side of the machine).

Unplug the CubeX screen.

5

Lift the case up off the CubeX.

Using the 3mm hex driver undo the 5 bolts holding the floor panel to the machine.

Lift the front of the floor panel and cable tie it to the bed arms. This will allow you

access to the Main Board PCB.

6

Removing the damaged Main Board PCB

Before removing the Main board PCB, label each of the looms that are plugged into

it. The PCB is marked to tell you which loom is plugged into which connector.

Remove the Looms and unplug the power supply from the main board PCB.

Gently pull up on the main board PCB to slide it off of the rubber ties holding it in

place.

7

Using the 2.5mm hex driver, undo the bolts holding the Print Jet driver boards to the

Main Board PCB and remove the Print Jet driver boards. (Note the amount of Print

Jet driver boards will correspond with the amount of Print Jets present on your

CubeX printer)

Fitting the new Main Board PCB

Plug the Extruder Driver boards into the new Main Board PCB and fasten with bolts.

8

Pull the rubber ties up through the holes on the main board PCB to fasten it to the

CubeX.

Plug the looms and power supply back into their corresponding connectors.

Re attaching the floor panel and case.

Cut the cable tie holding the floor panel in place and gently lower it down.

9

Using the 3mm hex driver re attach the 5 bolts that hold the floor panel.

Slide the case onto the CubeX and plug in the CubeX screen.

Using the 3mm Driver re attach the 8 case bolts.

10

You may now power up your CubeX.

You will need to re activate your CubeX using the activation code associated

with your CubeX. You will also need to re set your Z height and offsets, if you

did not make a note of these settings you can find instructions on how to set

them in the CubeX users guide.

Andere Handbücher für Cubify CUBEX Duo

3

Inhaltsverzeichnis

Andere 3D Systems 3D-Drucker Handbücher

3D Systems

3D Systems CUBE Bedienungsanleitung

3D Systems

3D Systems ProJet 660Pro Bedienungsanleitung

3D Systems

3D Systems Cubify CUBEX Duo Bedienungs- und Sicherheitshinweise

3D Systems

3D Systems ProJet 4500 Bedienungsanleitung

3D Systems

3D Systems ProJet 1200 Bedienungsanleitung

3D Systems

3D Systems Cubify CUBEX Duo Bedienungsanleitung

3D Systems

3D Systems Cube 3rd Generation Bedienungsanleitung

3D Systems

3D Systems ProJet 4500 Bedienungsanleitung

3D Systems

3D Systems CubePro Bedienungsanleitung

3D Systems

3D Systems PostCure 1050 Bedienungsanleitung

3D Systems

3D Systems NextDent 5100 Bedienungsanleitung

3D Systems

3D Systems ProJet 4500 Bedienungsanleitung

3D Systems

3D Systems CUBE Bedienungsanleitung

3D Systems

3D Systems ProJet MJP 3600 Bedienungsanleitung

3D Systems

3D Systems ProX 800 Bedienungsanleitung

3D Systems

3D Systems CUBE Bedienungsanleitung

3D Systems

3D Systems iPro 8000 SLA Center Bedienungsanleitung

3D Systems

3D Systems ProX DMP 100 Bedienungsanleitung

3D Systems

3D Systems projet mjp 2500 Bedienungsanleitung

3D Systems

3D Systems CUBE Bedienungsanleitung

3D Systems

3D Systems CubeX Bedienungsanleitung

3D Systems

3D Systems CUBE Bedienungsanleitung

3D Systems

3D Systems Cubify CUBEX Duo Stücklistenhandbuch

3D Systems

3D Systems ProX 950 Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch